SLSergio Vela Liñán

Sergio Vela Liñán

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sergio Vela Liñán has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of a capping layer on ultrashort pulse laser removal of thin oxide films

    by Maximilian Spellauge, Sergio Vela Liñán, Pau Estarlich, Gerard Masmitja, Cristobal Voz, Philipp Schmid, Constanze Eulenkamp, David Canteli, Carlos Molpeceres Álvarez, Miguel Morales Furió, et al.

    Laser-based selective thin film removal is a key process in microelectronics manufacturing, where functional layers must be removed with high precision while preserving the integrity of the underlying substrate. In many technologically relevant systems, thin films are covered by additional capping layers, whose influence on the removal mechanisms remains poorly understood. In this work, we investigate the selective laser removal of VOx and AZO-capped VOx thin films deposited on silicon using time-resolved pump–probe microscopy in combination with final state crater analysis. For both systems, thin film removal is governed by indirectly induced ablation, whereby laser energy is predominantly absorbed in the silicon substrate, leading to stress-driven film lift-off. At higher fluences, the onset of phase explosion induces substrate damage and prevents selective thin film removal. The presence of the AZO capping layer reduces the processing fluence window for selective thin film removal by approximately 30%, enhances the confinement of the molten substrate and suppresses silicon substrate removal. In addition, residual fragments of the capping layer remain on the surface after processing. These findings demonstrate that capping layers significantly alter both the process window and the underlying removal dynamics and must therefore be carefully considered in the design and optimization of laser-based thin film removal processes.

  • Development and validation of numerical models for laser ablation with ultrashort pulses

    by Sergio Vela Liñán

    During the last decades, laser ablation has become a major research field due to its wide-ranging industrial and scientific applications. This doctoral thesis addresses the numerical simulation of USP ablation, aiming to deepen the theoretical understanding of underlying physical phenomena and to support process optimization. Structured in seven chapters, the thesis follows a logical progression from fundamentals to novel model development and validation: Chapter 1 reviews the fundamentals of laser ablation, beginning with a historical overview and the description of pulses following a Gaussian beam. It then discusses heat conduction models applicable to different pulse durations, notably the Two-Temperature Model (TTM) for femtosecond (fs) pulses. Key ablation mechanismssuch as spallation and phase explosionare described, and various modelling approaches (hydrodynamic, molecular dynamics) are reviewed. The absorption of laser radiation by different material types (metals, semiconductors, dielectrics) is discussed, followed by an overview of key USP ablation applications. Chapter 2 describes the experimental and numerical methodologies. Firstly, the femtosecond and nanosecond laser systems, along with diagnostic tools such as confocal and scanning electron microscopy, are detailed. Then, experimental procedures for determining ablation thresholds and crater geometries such as the Liu method and depth-based fitting are explained. The chapter also introduces the numerical and mathematical tools used in simulations, including finite difference methods and polylogarithms. Chapter 3 focuses on nanosecond ablation modelling using both COMSOL Multiphysics and MATLAB. The variation of the materials thermal parameters which temperature has been considered, and ablation is modelled by removing material once vaporization temperature is reached. The simulated crater diameters are compared with experimental measurements for the particular case of copper oxide thin films, showing strong agreement. Chapter 4 presents a new analytical solution for the electron heat capacity in s-band metals, within the free electron gas model (FEG) framework. The calculations employ a special type of functions called polylogarithms. Our new solution shows good agreement with more complex DFT calculations, making it suitable for numerical simulations of USP ablation later in this thesis. Moreover, a cubic approximation for the low-temperature regime is also derived from the exact solution for faster computation. Chapter 5 presents a novel MATLAB code which numerically solves the TTM equations using finite difference methods, in order to calculate the temperature evolution of an aluminium target irradiated by a fs pulse. All relevant thermal and optical parameters are treated as temperature dependent, and ablation is modelled by the consideration of the phase explosion condition. The model predictions are validated against both our own experiments and published data, showing strong agreement between experiments and simulations. Chapter 6 develops and validates the Threshold Refined Model (TRM) for predicting ablation efficiency of ultra-short pulses. By incorporating an initial ablation depth, $d_0$, the model accounts for spallation and reconciles the differences between different experimental threshold determination methods. The TRM was tested against a broad set of experimental data for metals, semiconductors, dielectrics and biological tissues, demonstrating consistent improvements over preexisting models, such as the Furmanski-Neueschwander model (FNM). Finally, Chapter 7 concludes the thesis and outlines future work lines. Future research avenues include extending the MATLAB simulation code to multi-pulse ablation, incorporating the hyperbolic TTM for even shorter pulse durations, and refining the TRM model for broader applicability. RESUMEN Durante las últimas décadas, la ablación láser con pulsos ultracortos se ha convertido en un importante campo de investigación por sus múltiples aplicaciones industriales y científicas. Esta tesis doctoral aborda la simulación numérica de este fenómeno, con el objetivo de profundizar en la comprensión teórica de los procesos físicos implicados y contribuir a la optimización de sus aplicaciones. Estructurada en siete capítulos, la tesis sigue una secuencia lógica: El capítulo 1 repasa los fundamentos de la ablación láser, comenzando con una visión histórica. Después, se analizan los distintos modelos de conducción térmica, destacando el modelo de dos temperaturas (TTM) para pulsos de femtosegundos (fs). También se describen los fenómenos físicos clave en la ablación, como la espalación y la explosión de fase, se resumen diversas técnicas de modelización (hidrodinámica, dinámica molecular), y se discuten los mecanismos de absorción en distintos materiales (metales, semiconductores y dieléctricos). Finalmente, se ofrece una visión general de las principales aplicaciones. El capítulo 2 describe las metodologías experimentales y numéricas. Se detallan los sistemas láser de fs y ns empleados, junto con herramientas de medida como la microscopía confocal y electrónica de barrido. Posteriormente, se explican los procedimientos experimentales para determinar los umbrales de ablación y las geometrías de los cráteres, como el método de Liu y la evaluación de profundidades. También se detallan las herramientas matemáticas y numéricas utilizadas en las simulaciones, como métodos de diferencias finitas y polilogaritmos. El capítulo 3 se centra en el modelado de la ablación por ns empleando COMSOL Multiphysics y MATLAB. Para estas duraciones de pulso, la ablación se modeliza haciendo desaparecer material al alcanzar la...

  • Open Access

    Numerical simulation of femtosecond laser ablation of Aluminium

    by S. Vela, M. Morales, D. Munoz-Martin, C. Molpeceres


  • Open Access

    Photo-assisted spin transport in double quantum dots with spin–orbit interaction

    by David Fernández-Fernández, Jordi Picó-Cortés, Sergio Vela Liñán, Gloria Platero

    We investigate the effect of spin–orbit interaction on the intra- and interdot particle dynamics of a double quantum dot (QD) under ac electric fields. The former is modeled as an effective ac magnetic field that produces electric-dipole spin resonance transitions, while the latter is introduced via spin-flip tunneling amplitudes. We observe the appearance of non-trivial spin-polarized dark states (DSs), arising from an ac-induced interference between photo-assisted spin-conserving and spin-flip tunneling processes. These DSs can be employed to precisely measure the spin–orbit coupling in QD systems. Furthermore, we show that the interplay between photo-assisted transitions and spin-flip tunneling enables the system to operate as a highly tunable spin filter. Finally, we investigate the operation of the system as a resonant flopping-mode qubit for arbitrary ac voltage amplitudes, allowing for high tunability and enhanced qubit control possibilities.