Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Wai Tuck Chow has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Hybrid Gripper with Passive Jamming Fingers and Cable-Driven Joints for Enhanced Payload Capacity and Misalignment Tolerance

    by Douglas See Zheng Yu, Wai Tuck Chow, Bin Zhu

    Inspired by the human hand, this work presents a hybrid rigid–soft gripper that achieves passive adaptability through a self-resetting granular jamming pouch integrated onto a 3-DOF cable-driven rigid skeleton. Seven fingertip configurations (rigid tip, different jamming particles, and TPU-only) were evaluated across five object geometries. The jamming pouch configurations showed a clear advantage over rigid fingertips and a modest improvement over TPU-only fingertips when grasping flat or smoothly curved surfaces, while demonstrating substantially superior performance for objects with sharp protrusions, lips, undercuts, or deformable edges, where enhanced conformability and geometric interlocking markedly improved payload capacity and lateral offset tolerance. The passive self-reset mechanism remained reliable over 1000 cycles. These results demonstrate that the hybrid design effectively combines the advantages of rigid and soft grippers, achieving superior overall grasping performance while balancing adaptability and payload without pneumatic actuation, with strong potential for applications in logistics, food handling, and mobile robotics.

  • A multi-stage-based discretized jumping control algorithm of wheel-legged jumping robots

    by Xuefei Liu, Yi Sun, Youzhi Xu, Shutao Wu, Wai Tuck Chow, Aihong Ji

  • Open Access

    Lightweight and Low-Cost Cable-Driven SCARA Robotic Arm with 9 DOF

    by Yuquan Shi, Wai Tuck Chow, Thomas M. Kwok, Yilong Wang

    This paper presents the design and testing of a lightweight, low-cost robotic arm with an extended vertical range. The 9-degree-of-freedom (DOF) system comprises a 6-DOF arm and a 3-DOF gripper. To minimize weight, the six wrist and gripper joints are cable-driven, with all actuators relocated to the shoulder assembly. As a result, the wrist and gripper only weigh 222 g and 113 g, respectively, significantly reducing the inertia on the end effector. The arm utilizes a SCARA-configuration that slides along a tower for extended vertical reach. A key innovation is a closed-section frame that attaches the arm to the tower, in which the bending and torsional loads from the payload can be directly transferred onto the static structure. In contrast to conventional design, this design does not require the shoulder motor to take the bending load directly. Instead, the motor only needs to overcome the rolling friction of the reaction load. Experimental results demonstrate that this approach reduces the required motor torque by a factor of 30. Consequently, the prototype can manipulate a 3 kg payload at a 0.5 m lateral reach while weighing only 4.5 kg, costing USD 1200, and consuming a maximum of 11.1 W of power.


  • Open Access

    A Wearable Stiffness-Rendering Haptic Device with a Honeycomb Jamming Mechanism for Bilateral Teleoperation

    by Thomas M. Kwok, Bohan Zhang, Wai Tuck Chow

    This paper addresses the challenge of providing kinesthetic feedback in bilateral teleoperation by designing a wearable, lightweight (20 g), and compact haptic device, the HJ-Haptic, utilizing a honeycomb jamming mechanism for object stiffness rendering. The HJ-Haptic device can vary its stiffness, from 1.15 N/mm to 2.64 N/mm, using a 30 kPa vacuum pressure. We demonstrate its implementation in a teleoperation framework, enabling operators to adjust grip force based on a reliable haptic feedback on object stiffness. A three-point flexural test on the honeycomb jamming mechanism and teleoperated object-grasping tasks were conducted to evaluate the device’s functionality. Our experiments demonstrated a small RMSE and strong correlations in teleoperated motion, stiffness rendering, and interaction force feedback. The HJ-Haptic effectively adjusts its stiffness in response to real-time gripper feedback, mimicking the sensation of direct object grasping with hands. The device’s use of vacuum pressure ensures operator safety by preventing dangerous outcomes in case of gas leakage or material failure. Incorporating the HJ-Haptic into the teleoperation framework provided the reliable perception of object stiffness and stable teleoperation. This study highlights the potential of the honeycomb jamming mechanism for enhancing haptic feedback in various applications, including teleoperation scenarios, as well as interactions with extended-reality environments.


  • Open Access

    V-Spline Design for Enhanced Performance in Turbine Blade Internal Cooling

    by Symus Say, Adamya Singh Dhaker, Wai Tuck Chow

    Past experiments have consistently shown that V-shaped rib turbulators are among the best in heat transfer performance. While there is literature on the V rib design in various experimental studies, there is no literature that shows the V rib design applied on any current turbine blades. Instead, the straight and angled rib design are used. The V rib only offers a marginally better heat transfer performance over the angled rib, but it has a severe stress concentration at the rib tip. In this research, multiple design augmentations were analyzed, with the addition of a spline at the center of the V exhibiting alleviation of the tip stress concentration. The results show that the presence of the spline not only resolves the fatigue issues but also increases the heat transfer performance by 4.3% and 8.2% against the V rib and angled rib design, respectively. With a better heat transfer performance, the creep analysis shows that the turbine blade with a V-spline rib design can operate at temperatures 203 °C hotter than an angled rib at the same fluid power. Given the dependence of engine thermal efficiency on turbine inlet temperature, this simple design shows good potential for heat transfer augmentation.


  • Open Access

    A Decoupling Module Based on a Geometrical-Balance Mechanism for Mitigating Cable Length Variation in Cable-Driven Applications

    by Van Pho Nguyen, Sunil Bohra Dhyan, Wai Tuck Chow

    Cable-driven mechanisms are increasingly popular in applications requiring low-inertia operation. However, issues like cable loosening, which leads to reduced durability and stability with long-term use, have not been fully addressed in previous studies. This paper presents a novel design for a decoupling mechanism based on the geometrical-balance principle. The mechanism incorporates three pulleys—main, minor, and guiding—mounted on a parallelogram structure. The cable passes over these pulleys and an elbow pulley with constant tension, maintained through a balance between the pulleys’ radii and the cable’s thickness and radius. A theoretical model was developed to estimate deviations in the cable tension within this design, considering general geometric parameters and friction coefficients. In the experimental setup, the main pulley had a radius of 15 mm, while the minor, guiding, and elbow pulleys had radii of 7 mm, and a 1 mm radius Dyneema cable was used. The results demonstrated that the decoupling mechanism maintained a consistent cable length and tension with minimal deviation as the two links rotated from small to large angles. Furthermore, a strong correlation between the theoretical estimates and experimental validation confirmed that the cable tension remained stable at both ends when the decoupling mechanism was integrated into the original system. This research improves the stability and durability of cable-driven mechanisms while offering a compact, accurate solution adaptable to a wide range of applications, including robotics, machinery, and other devices.


  • Open Access

    Soft Robotic Honeycomb-Velcro Jamming Gripper Design

    by Yu Cheng Chung, Wai Tuck Chow, Van Pho Nguyen

    In this paper, using a honeycomb-velcro structure to generate a novel jamming gripper is explored. Each finger of the gripper consists of multi-layers with a honeycomb sandwich structure acting as a core wrapped by a fabric sheet and sealed by a latex membrane. This structure can transit between unjammed (flexible) and jammed (rigid) states thanks to the vacuum pressure. Various materials of honeycomb structure, fabric, and reinforcements are investigated to seek optimal combinations for making the jamming fingers. Then, such fingers are deployed in experiments to evaluate the stiffness and the surface friction with different loads in terms of with or without vacuum. Vacuum pressure boosts the stiffness and friction of all the jamming fingers compared with the without-vacuum case. Attached to a gripper, the jamming finger shows good performance in diverse manipulation with food, a metal component, a toy, a can, and a bottle. Furthermore, the variable-stiffness finger under vacuum pressure can be utilized to perform assembly and installation operations such as pushing a bolt into an aligned hole.


  • Open Access

    Low-Cost Cable-Driven Robot Arm with Low-Inertia Movement and Long-Term Cable Durability

    by Van Pho Nguyen, Wai Tuck Chow, Sunil Bohra Dhyan, Bohan Zhang, Boon Siew Han, Hong Yee Alvin Wong

    Our study presents a novel design for a cable-driven robotic arm, emphasizing low cost, low inertia movement, and long-term cable durability. The robotic arm shares similar specifications with the UR5 robotic arm, featuring a total of six degrees of freedom (DOF) distributed in a 1:1:1:3 ratio at the arm base, shoulder, elbow, and wrist, respectively. The three DOF at the wrist joints are driven by a cable system, with heavy motors relocated from the end-effector to the shoulder base. This repositioning results in a lighter cable-actuated wrist (weighing 0.8 kg), which enhances safety during human interaction and reduces the torque requirements for the elbow and shoulder motors. Consequently, the overall cost and weight of the robotic arm are reduced, achieving a payload-to-body weight ratio of 5:8.4 kg. To ensure good positional repeatability, the shoulder and elbow joints, which influence longer moment arms, are designed with a direct-drive structure. To evaluate the design’s performance, tests were conducted on loading capability, cable durability, position repeatability, and manipulation. The tests demonstrated that the arm could manipulate a 5 kg payload with a positional repeatability error of less than 0.1 mm. Additionally, a novel cable tightener design was introduced, which served dual functions: conveniently tightening the cable and reducing the high-stress concentration near the cable locking end to minimize cable loosening. When subjected to an initial cable tension of 100 kg, this design retained approximately 80% of the load after 10 years at a room temperature of 24 °C.


  • Soft Robotic Honeycomb Jamming Gripper Design

    by Yu Cheng Chung, Wai Tuck Chow

    Jamming grippers, based on the principles of granular material jamming, have gathered significant attention over the years. Jamming grippers can perform well in grasping objects of different shapes and sizes. However, such designs tend to be bulky and often not suitable to take bending loads. In this paper, a novel idea of using a honeycomb structure in a jamming gripper is being explored. Using honeycomb as the jamming material, it is possible to design a slender and lightweight finger for dexterous gripping. The bending stiffness of the finger can be varied by modulating the air pressure within the membrane, allowing the honeycomb sandwich structure to transit between unjammed (flexible) and jammed (rigid) states. Various materials of honeycomb structure, fabric and reinforcement were explored to find a suitable combination of materials for the gripper. Experiments were conducted on the gripper and the honeycomb jamming gripper displayed great grasping capabilities.