Muhammad Zuchry
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Muhammad Zuchry has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Hairul Arsyad
Hasanuddin University, Indonesia
2 shared publications - Ilyas Renreng
Hasanuddin University, Indonesia
2 shared publications - Lukman Hakim
Universitas Ahmad Dahlan
2 shared publications - Agus Widyianto
Universitas Negeri Yogyakarta, Sleman, INDONESIA
1 shared publication
Latest Publications
- Open Access
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (6 (124)) , 45-50
Effect of anodizing on aluminum alloy 2024 with boric sulfate acid in medium 3.5 % NaCl
The utilization of metal materials finds widespread applications in various industries, including the aircraft industry, where aluminum alloys are commonly employed. However, metal materials are prone to corrosion under specific conditions, necessitating the implementation of corrosion prevention methods to decelerate the material's corrosion rate. Corrosion is a process in which the quality of metal deteriorates due to environmental influences. An effective approach to inhibit corrosion is through anodizing, which involves applying a protective coating to the metal surface, preventing direct contact with the surrounding environment. In this research, the focus was on studying the corrosion rate of aluminum alloy 2024 using Boric Sulfate Acid Anodizing (BSAA) at 10 volts and immersion times of 10, 15, and 20 minutes, followed by sealing with acetic acid in a corrosive environment containing 3.5 % NaCl. The main goals were to evaluate the effectiveness of anodizing with and without sealing in lowering the rate of aluminum corrosion, to compare the effectiveness of anodizing with and without sealing, and to create adsorption models using Langmuir adsorption. Through the examination of the potentiodynamic approach, it was shown that anodizing had an inhibitory impact that was strengthened by sealing. The maximum efficiency of 76 % was attained after 20 minutes of anodizing and sealing at 10 volts. A correlation value of 0.7487 from the Langmuir adsorption modeling was also obtained, pointing to an advantageous adsorption behavior. This research demonstrates how effectively anodizing for aluminum alloy 2024 works with and without sealing, especially in a 3.5 % NaCl-corrosive environment
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (6 (124)) , 45-50
Open AccessEffect of anodizing on aluminum alloy 2024 with boric sulfate acid in medium 3.5 % NaCl
The utilization of metal materials finds widespread applications in various industries, including the aircraft industry, where aluminum alloys are commonly employed. However, metal materials are prone to corrosion under specific conditions, necessitating the implementation of corrosion prevention methods to decelerate the material's corrosion rate. Corrosion is a process in which the quality of metal deteriorates due to environmental influences. An effective approach to inhibit corrosion is through anodizing, which involves applying a protective coating to the metal surface, preventing direct contact with the surrounding environment. In this research, the focus was on studying the corrosion rate of aluminum alloy 2024 using Boric Sulfate Acid Anodizing (BSAA) at 10 volts and immersion times of 10, 15, and 20 minutes, followed by sealing with acetic acid in a corrosive environment containing 3.5 % NaCl. The main goals were to evaluate the effectiveness of anodizing with and without sealing in lowering the rate of aluminum corrosion, to compare the effectiveness of anodizing with and without sealing, and to create adsorption models using Langmuir adsorption. Through the examination of the potentiodynamic approach, it was shown that anodizing had an inhibitory impact that was strengthened by sealing. The maximum efficiency of 76 % was attained after 20 minutes of anodizing and sealing at 10 volts. A correlation value of 0.7487 from the Langmuir adsorption modeling was also obtained, pointing to an advantageous adsorption behavior. This research demonstrates how effectively anodizing for aluminum alloy 2024 works with and without sealing, especially in a 3.5 % NaCl-corrosive environment
- Open Access
- 30 April 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (122)) , 43-52
Sealing effect on corrosion resistance of boric sulfuric acid anodizing on AA2024
Aluminum is widely used due to its excellent properties, lightweight and thermal conductivity. However, when used in aircraft applications, it can cause corrosion and sticking, compromising safety. To address this issue, anodizing is used to improve aluminum's corrosion resistance and adhesion. In this study, the AA2024 material was anodized using the boron-sulfuric acid anodization (BSAA) process, followed by a sealing process using acetic acid. This sealing process forms an oxide layer on the aluminum's surface, which reduces the corrosion rate. The study investigated the effects of anodization voltage and time on the results of BSAA anodization through quantitative and qualitative measurements, including corrosion resistance, potentiodynamic polarization, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results showed that samples anodized with a gasket could reduce the corrosion rate by up to 85 % compared to those without a gasket and substrate. The most significant reduction in corrosion rates occurred at an anodization voltage of 10 V and an anodization time of 15 min. The potentiodynamic test results indicated that the Tafel plot during sealing lies in the cathodic region where the corrosion current density decreases with increasing voltage. SEM observations revealed that the anodizing process could provide an oxide layer on the samples' surface, while the sealing process creates a smooth surface. EDS analysis showed that an oxide compound was formed in an oxide bond state after the sample surface was subjected to the sealing treatment. Overall, the study demonstrates the effectiveness of BSAA anodization in improving corrosion resistance and highlights the importance of considering the anodization parameters
- 30 April 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (122)) , 43-52
Open AccessSealing effect on corrosion resistance of boric sulfuric acid anodizing on AA2024
Aluminum is widely used due to its excellent properties, lightweight and thermal conductivity. However, when used in aircraft applications, it can cause corrosion and sticking, compromising safety. To address this issue, anodizing is used to improve aluminum's corrosion resistance and adhesion. In this study, the AA2024 material was anodized using the boron-sulfuric acid anodization (BSAA) process, followed by a sealing process using acetic acid. This sealing process forms an oxide layer on the aluminum's surface, which reduces the corrosion rate. The study investigated the effects of anodization voltage and time on the results of BSAA anodization through quantitative and qualitative measurements, including corrosion resistance, potentiodynamic polarization, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results showed that samples anodized with a gasket could reduce the corrosion rate by up to 85 % compared to those without a gasket and substrate. The most significant reduction in corrosion rates occurred at an anodization voltage of 10 V and an anodization time of 15 min. The potentiodynamic test results indicated that the Tafel plot during sealing lies in the cathodic region where the corrosion current density decreases with increasing voltage. SEM observations revealed that the anodizing process could provide an oxide layer on the samples' surface, while the sealing process creates a smooth surface. EDS analysis showed that an oxide compound was formed in an oxide bond state after the sample surface was subjected to the sealing treatment. Overall, the study demonstrates the effectiveness of BSAA anodization in improving corrosion resistance and highlights the importance of considering the anodization parameters