HAHairul Arsyad

Hairul Arsyad

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hairul Arsyad has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Efek tegangan dan konsentrasi larutan asam sulfat pada Pembentukan burned anodizing pada proses anodisasi aluminum Foil

    by Hairul Arsyad, Nurkhofifah Marsing

    The surface engineering process involving electrochemical methods is the anodization process. Anodization is an electrochemical process that produces anodic oxide on the surface that can change the surface proper-ties. In the anodization process, burned anodizing and surface cracking during the anodizing process hurt the surface quality. This study tries to see the formation of an aluminum oxide layer that causes burned an-odizing and surface cracking by adjusting the voltage and concentration of the solution. This study uses aluminum foil as a sample and graphite as an electrode. Anodization is carried out by providing a voltage range of 8 to 16 volts at two H2SO4 solution 2M and 3M concentrations. Observations of surface character-istics include micro and macro surface structures, surface roughness, and surface morphology. Calculations of the burned area are also carried out for each treatment. The test results show that the percentage of burned area increases with increasing voltage and concentration. The smallest burned area percentage was obtained with a value of 4% for samples at a voltage of 8 Volts and a solution concentration of 2M. In con-trast, the maximum value was obtained, reaching 95% of the area burned on the surface for samples of 16 Volts at a concentration of 3 M. However, a tendency was obtained to decrease surface roughness with in-creasing anodization voltage in both the non-burned and burned areas. From the test results using SEM, it was also found that surface cracks occurred in addition to being burned on the surface

  • Open Access

    The influence of zinc content and sintering temperature on microstructure, hardness and corrosion potential of Mg-Zn-Ca alloy

    by Hairul Arsyad, Lukmanul Hakim Arma, R Rudi, Y Yuliana

    Mg-Zn-Ca alloy, a material widely recognized for its potential as a biomaterial, has been the focus of our research. In this work, powder metallurgy was used to create three alloys with mass fractions: 89Mg-10Zn-1Ca, 93Mg-6Zn-1Ca, and 97Mg-2Zn-1Ca wt.%. Powders were mixed in the mentioned parts where magnesium served as the substrate. The compaction pressure applied to the sample was 200 MPa. The sintering process was then conducted at two temperature levels, 500?C and 600?C, in an argon gas environment. Hardness and microstructural observations were conducted on the samples. Electrochemical corrosion tests were performed using a potentiometer. Additionally, the potential of hydrogen (pH) value in simulated body fluid was evaluated. The results indicated that the alloy with the highest zinc content of 10% at a sintering temperature of 600?C exhibited the best potential as an implant material, showing the highest hardness test results and the lowest corrosion rate.

  • Open Access

    Development of a fuzzy logic model for predicting the quality of micro friction stir spot welding (µFSSW) using particle swarm optimization

    by Hairul Arsyad, Semuel Boron Membala, Agus Widyianto, Muhammad Syahid, Lukmanul Hakim Arma, Rudi Rudi, Saiful Mangngenre, Rudi

    Micro Friction Stir Spot Welding (µFSSW) is crucial in microelectronics and precision manufacturing. It requires a comprehensive understanding of the complex connections between various parameters to achieve the highest quality welds. This study aims to improve the prediction of µFSSW weld quality by incorporating advanced optimization techniques. Fuzzy Logic Optimization is used to model uncertainties, and Particle Swarm Optimization (PSO) is employed to fine-tune parameters for improved accuracy. The fuzzy logic system utilizes Gaussian functions as membership functions, organized with nine rule bases. The results clearly demonstrate that the fuzzy logic model greatly enhances accuracy when combined with Particle Swarm Optimization. The refined model improves precision for pin diameter, shoulder diameter, Thermo-Mechanically Affected Zone (TMAZ) area, and cross-tensile strength. The PSO-optimized model shows lower accuracy in predicting plunge depth and shear tensile strength. The ongoing decline in Root Mean Square Error (RMSE) values highlights the complexity of the results. The optimization significantly improves the model’s ability to predict specific weld quality metrics, as demonstrated by the pin diameter’s reduced RMSE value of 0.07. The collective results showcase an optimized Fuzzy Logic System (FLS) model adept at accurately predicting µFSSW weld quality, demonstrating adaptability across diverse conditions. The discernible increase in accuracy, reaching up to 76 % following the optimization of the fuzzy logic model with PSO, serves as a testament to the efficacy of the employed methodologies in advancing the precision and reliability of µFSSW weld quality predictions Точкове зварювання мікротертям з перемішуванням (µFSSW) має вирішальне значення в мікроелектроніці та прецизійному виробництві. Для досягнення найвищої якості зварних швів необхідне всебічне розуміння складних зв’язків між різними параметрами. Дане дослідження спрямоване на покращення прогнозування якості зварного шва µFSSW шляхом впровадження передових методів оптимізації. Оптимізація з використанням нечіткої логіки застосовується для моделювання невизначеностей, а метод рою часток (PSO) використовується для точного налаштування параметрів для підвищення точності. Система нечіткої логіки використовує гауссові функції в якості функцій приналежності, організованих за допомогою дев’яти баз правил. Результати чітко демонструють, що у поєднанні з методом рою часток модель нечіткої логіки значно підвищує точність. Удосконалена модель підвищує точність визначення діаметра штифта, діаметра заплечика, зони термомеханічного впливу (TMAZ) і межі міцності при поперечному розтягуванні. Модель, оптимізована за допомогою PSO, показує нижчу точність прогнозування глибини занурення та межі міцності при розтягуванні при зсуві. Триваюче зниження значень середньоквадратичної помилки (RMSE) підкреслює складність результатів. Оптимізація значно покращує здатність моделі прогнозувати конкретні показники якості зварного шва, про що свідчить зменшене значення RMSE діаметра штифта 0,07. Сукупні результати демонструють оптимізовану модель системи нечіткої логіки (FLS), здатну точно прогнозувати якість зварного шва µFSSW, демонструючи адаптивність у різних умовах. Помітне збільшення точності, що досягає 76 % після оптимізації моделі нечіткої логіки за допомогою PSO, служить свідченням ефективності використовуваних методик в підвищенні точності і надійності прогнозування якості зварних швів µFSSW

  • Open Access

    Optimization of resistance spot welding with surface roughness dissimilar mild steel with stainless steel

    by Ariyanto Ariyanto, Muhammad Setiawan Sukardin, Ilyas Renreng, Hairul Arsyad, Muhammad Syahid, Muhammad Alwi

    Resistance spot welding plays a critical role in the manufacture dissimilar material industry. However, there are differences in mechanical properties between mild steel and satinless steel so as to reduce the quality of welded joints. In order for differences in mechanical properties to be corrected, surface roughness was treated. The aim of this study was to optimize the welding parameters of DRSW with surface roughness by analysis using the Taguchi and Anova Methods. In this study discusses about investigates the Resistance spot welding parameters on weld geometry, mechanical properties, and SEM EDS on dissimilar materials of mild steel and stainless steel. The material thickness of the mild steel and stainless steel are 1 mm, respectively. The process parameters of the resistance spot welding joint used, example; surface roughness, current, welding time, and electrode force. Quality welding joint test results include weld geometry, mechanical properties, and SEM EDS. Weld geometry testing to determine the weld nugget profile. The mechanical properties test was shear tensile test, while the SEM EDS included macrostruture and microstructure observations. The results showed the highest nugget diameter 6.65 mm highest shear tensile strength 7.66 kN. The most influential parameter is current by 75.08 %, then surface roughness by 12.35 %. The highest tensile strength has fewer defects. Surface roughness treatment before welding is very good to make welding quality joints between mild steel and quality stainless steel increase. Surface roughness treatment was very good to be included when making welding procedures for welding engineers for welding processes resistance spot welding dissimilar mild steel with stainless steel.


  • Open Access

    Effect of anodizing on aluminum alloy 2024 with boric sulfate acid in medium 3.5 % NaCl

    by Muhammad Zuchry, Ilyas Renreng, Hairul Arsyad, Lukmanul Hakim Arma

    The utilization of metal materials finds widespread applications in various industries, including the aircraft industry, where aluminum alloys are commonly employed. However, metal materials are prone to corrosion under specific conditions, necessitating the implementation of corrosion prevention methods to decelerate the material's corrosion rate. Corrosion is a process in which the quality of metal deteriorates due to environmental influences. An effective approach to inhibit corrosion is through anodizing, which involves applying a protective coating to the metal surface, preventing direct contact with the surrounding environment. In this research, the focus was on studying the corrosion rate of aluminum alloy 2024 using Boric Sulfate Acid Anodizing (BSAA) at 10 volts and immersion times of 10, 15, and 20 minutes, followed by sealing with acetic acid in a corrosive environment containing 3.5 % NaCl. The main goals were to evaluate the effectiveness of anodizing with and without sealing in lowering the rate of aluminum corrosion, to compare the effectiveness of anodizing with and without sealing, and to create adsorption models using Langmuir adsorption. Through the examination of the potentiodynamic approach, it was shown that anodizing had an inhibitory impact that was strengthened by sealing. The maximum efficiency of 76 % was attained after 20 minutes of anodizing and sealing at 10 volts. A correlation value of 0.7487 from the Langmuir adsorption modeling was also obtained, pointing to an advantageous adsorption behavior. This research demonstrates how effectively anodizing for aluminum alloy 2024 works with and without sealing, especially in a 3.5 % NaCl-corrosive environment


  • Open Access

    Sealing effect on corrosion resistance of boric sulfuric acid anodizing on AA2024

    by Muhammad Zuchry, Ilyas Renreng, Hairul Arsyad, Lukmanul Hakim Arma, Agus Widyianto

    Aluminum is widely used due to its excellent properties, lightweight and thermal conductivity. However, when used in aircraft applications, it can cause corrosion and sticking, compromising safety. To address this issue, anodizing is used to improve aluminum's corrosion resistance and adhesion. In this study, the AA2024 material was anodized using the boron-sulfuric acid anodization (BSAA) process, followed by a sealing process using acetic acid. This sealing process forms an oxide layer on the aluminum's surface, which reduces the corrosion rate. The study investigated the effects of anodization voltage and time on the results of BSAA anodization through quantitative and qualitative measurements, including corrosion resistance, potentiodynamic polarization, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results showed that samples anodized with a gasket could reduce the corrosion rate by up to 85 % compared to those without a gasket and substrate. The most significant reduction in corrosion rates occurred at an anodization voltage of 10 V and an anodization time of 15 min. The potentiodynamic test results indicated that the Tafel plot during sealing lies in the cathodic region where the corrosion current density decreases with increasing voltage. SEM observations revealed that the anodizing process could provide an oxide layer on the samples' surface, while the sealing process creates a smooth surface. EDS analysis showed that an oxide compound was formed in an oxide bond state after the sample surface was subjected to the sealing treatment. Overall, the study demonstrates the effectiveness of BSAA anodization in improving corrosion resistance and highlights the importance of considering the anodization parameters


  • Open Access

    Suppression of corrosion on stainless steel 303 with automatic impressed current cathodic protection (a-ICCP) method in simulated seawater

    by Hamsir Hamsir, Onny Sutresman, Hairul Arsyad, Muhammad Syahid, Agus Widyianto

    One effective method to slow down metal corrosion rate is the impressed current cathodic protection (ICCP) system. The ICCP system is suitable for coastal applications such as piping systems and offshore structures. In this application, metal surfaces tend to be exposed to seawater. Specific concentrations of seawater can accelerate the occurrence of corrosion of metals, even though they are stainless steel types. This study applied the automatic ICCP system to stainless steel 303. Stainless steel 303 will be immersed in simulated seawater at several concentrations of NaCl (27 ppt, 31 ppt, and 35 ppt). The specimens were immersed in NaCl solution for three weeks or about 504 hours at a constant temperature of 38 °C. After the sample has been soaked, quantitative and qualitative measurements were carried out. Quantitative measures include average weight loss, corrosion rate, and potential value. At the same time, the qualitative measurements include macroscopic, Scanning Electron Microscopy (SEM), and Energy Dispersive X-Ray Spectroscopy (EDS). Based on quantitative measures, it was found that the difference in average weight loss and corrosion rate for each NaCl concentration was not very significant. The difference of each parameter is less than 0.1 % and 0.22 %, respectively. The potential value quickly reaches a steady state at NaCl concentrations of 27 ppt and 31 ppt in less than 10 seconds. The results of the SEM test showed a change in the metal structure. The oxygen (O) content in the metal after the EDS test showed a decrease in this element up to 35 % at a NaCl concentration of 35 ppt. The decrease in oxygen (O) can slow down the corrosion rate in metals when exposed to seawater.


  • Open Access

    Indentifying the effect of micro friction stir spot welding (µFSSW) parameters on weld geometry, mechanical properties, and metallography on dissimilar materials of AZ31B and AA1100

    by Semuel Boron Membala, Onny Sutyono Sutresman, Hairul Arsyad, Muhammad Syahid, Agus Widyianto

    Micro-friction stir spot welding (µFSSW) is one type of welding that is suitable for joining lightweight materials. One of the challenges in joining lightweight materials with µFSSW is that the material is easily perforated, or the join is not strong enough, so it is necessary to select the right µFSSW parameters. In this article discusses about investigates the micro-Friction Stir Spot Welding (µFSSW) parameters on weld geometry, mechanical properties, and metallography on dissimilar materials of AZ31B and AA1100. The material thickness of the AZ31B and AA100 is 0.5 mm and 0.32 mm, respectively. The µFSSW tool is made of high-speed steel (HSS) with a pin diameter of 0.25 mm and a shoulder diameter of 0.5 mm. The constant process parameters of the µFSSW joint used, i. e., plunge depth, dwell time plunge rate, and high tool rotational speed of 33,000 rpm. Welding test results include weld geometry, mechanical properties, and metallography. Weld geometry testing to determine the weld nugget diameter. The mechanical properties test was shear tensile test and cross tensile test, while the metallographic test included macrostructure and microstructure observations. The results of the FSSW weld geometry show that at a dwell time of 700 milliseconds and a plunge depth of 600 microns, the weld pin diameter and weld shoulder diameter are close to the pin diameter and the diameter of the shoulder tool used. Dwell time and plunge depth has a significant effect on tensile strength. The maximum shear and cross loads achieved were 387±17 N and 29±2 N, respectively. Intermetallic compounds (IMC) are observed at the interface of the two materials, while a dwell time of 700 milliseconds give the effect of cracks on the inside of the weld


  • Open Access

    Sodium bicarbonate treatment of coir fiber on wettability and shear strength of coir fiber-epoxy composite

    by Bakri Bakri, A E E Putra, I Renreng, H Arsyad, A A Mochtar

    This research presented the influence of treated coir fiber with sodium bicarbonate on wettability and interfacial shear strength (IFSS) of coir fiber-epoxy composite. Coir fibers were immersed in the solution of sodium bicarbonate with three different densities (8wt%, 10wt%, and 12wt %) for 24 hours and 120 hours. Epoxy resin was utilized as a matrix of composite. Wettability and IFSS of coir fiber-matrix adhesion were evaluated. Fiber wettability to the matrix was performed by measuring the droplet contact angle. In addition, the IFSS of coir fiber - epoxy matrix was investigated by pull out method. The surface morphology of interfacial bonding between fiber and matrix after pull out testing was evaluated by scanning electron microscopy (SEM). The results show that fiber surface wettability was influenced by sodium bicarbonate where the contact angle decrease after treatment. It suggests that good wetting of fiber and matrix. While the density of 12 wt% sodium bicarbonate for 120 hours possessed the highest interfacial shear strength of fiber-epoxy adhesion compared with other densities.