Hanifi Küçüksarıyıldız
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hanifi Küçüksarıyıldız has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bekir Güney
Karamanoglu Mehmetbey University
5 shared publications - Kazım Çarman
Selcuk Universitesi
3 shared publications - Eyüb Canli
Selcuk Universitesi
2 shared publications - İbRahim Mutlu
Faculty of Technology, Afyon Kocatepe University, Afyonkarahisar, Türkiye
2 shared publications - Hüseyin Kaya
Karamanoğlu Mehmetbey Üniversitesi
1 shared publication - Kadir Sabanci
Karamanoğlu Mehmetbey Üniversitesi
1 shared publication
Latest Publications
- 29 September 2026
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 11 (3) , 2205-2229
MATLAB-Based analysis of energy recovery performance of regenerative braking systems under different driving conditions in electric vehicles
The limited battery capacity of electric vehicles has made the development of effective energy management strategies essential for improving energy efficiency and extending driving range. Regenerative braking systems contribute to this objective by converting the vehicle's kinetic energy during braking into electrical energy and storing it in the battery. In this study, the effects of different driving conditions on regenerative braking performance were comparatively investigated using a unified MATLAB-based computational model applied to four different electric vehicle segments. Four vehicle models, namely Small EV, Sedan EV, SUV EV, and Large SUV, were evaluated under four representative driving scenarios: urban, intercity, highway, and hilly-road driving. The model was used to calculate energy recovery efficiency, recovered energy, net energy consumption, specific energy consumption, and battery utilization ratio. The results showed that the energy recovery efficiency reached approximately 20% under urban driving conditions, whereas it decreased to approximately 3% during highway driving. Although an increase in vehicle mass resulted in a higher amount of recovered energy, it also led to greater overall energy consumption. The observed variations across driving scenarios were generally greater than the differences among vehicle segments. The main contribution of this study is the comprehensive evaluation of energy management performance by comparing different electric vehicle segments under identical computational and driving conditions. Furthermore, the proposed MATLAB-based computational model provides a practical and systematic framework for comparatively evaluating regenerative braking and energy management performance under different vehicle and driving conditions.
- 29 September 2026
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 11 (3) , 2205-2229
MATLAB-Based analysis of energy recovery performance of regenerative braking systems under different driving conditions in electric vehicles
The limited battery capacity of electric vehicles has made the development of effective energy management strategies essential for improving energy efficiency and extending driving range. Regenerative braking systems contribute to this objective by converting the vehicle's kinetic energy during braking into electrical energy and storing it in the battery. In this study, the effects of different driving conditions on regenerative braking performance were comparatively investigated using a unified MATLAB-based computational model applied to four different electric vehicle segments. Four vehicle models, namely Small EV, Sedan EV, SUV EV, and Large SUV, were evaluated under four representative driving scenarios: urban, intercity, highway, and hilly-road driving. The model was used to calculate energy recovery efficiency, recovered energy, net energy consumption, specific energy consumption, and battery utilization ratio. The results showed that the energy recovery efficiency reached approximately 20% under urban driving conditions, whereas it decreased to approximately 3% during highway driving. Although an increase in vehicle mass resulted in a higher amount of recovered energy, it also led to greater overall energy consumption. The observed variations across driving scenarios were generally greater than the differences among vehicle segments. The main contribution of this study is the comprehensive evaluation of energy management performance by comparing different electric vehicle segments under identical computational and driving conditions. Furthermore, the proposed MATLAB-based computational model provides a practical and systematic framework for comparatively evaluating regenerative braking and energy management performance under different vehicle and driving conditions.
- 15 September 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (5) , 2224-2231
Development and Experimental Validation of a Full-Scale Brake Disc/Pad Test Rig for Passenger Vehicles
Brake systems are among the most critical safety components in passenger vehicles, making the accurate evaluation of braking performance essential during the design and development process. This study presents the development of a low-cost, multifunctional brake test rig capable of evaluating the performance of disc–pad friction pairs under controlled laboratory conditions. The test rig consists of a hydraulic braking unit, an electric motor drive system, a frequency inverter, a hydraulic control unit, and a data acquisition system. Braking tests were performed using an OEM ventilated brake disc and pad set at an equivalent vehicle speed of 100 km/h under a hydraulic braking pressure of 20 bar. Vehicle speed, friction coefficient, and brake disc temperature were continuously monitored throughout the experiments. The results showed that the developed test rig provided stable and repeatable braking cycles. The coefficient of friction varied between 0.03 and 0.36, while the brake disc temperature gradually increased from approximately 60 °C to 80 °C during repeated braking cycles. The developed system successfully reproduced braking characteristics under the specified laboratory conditions and provides a practical, reliable, and cost-effective platform for brake performance evaluation and future friction material investigations.
- 15 September 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (5) , 2224-2231
Development and Experimental Validation of a Full-Scale Brake Disc/Pad Test Rig for Passenger Vehicles
Brake systems are among the most critical safety components in passenger vehicles, making the accurate evaluation of braking performance essential during the design and development process. This study presents the development of a low-cost, multifunctional brake test rig capable of evaluating the performance of disc–pad friction pairs under controlled laboratory conditions. The test rig consists of a hydraulic braking unit, an electric motor drive system, a frequency inverter, a hydraulic control unit, and a data acquisition system. Braking tests were performed using an OEM ventilated brake disc and pad set at an equivalent vehicle speed of 100 km/h under a hydraulic braking pressure of 20 bar. Vehicle speed, friction coefficient, and brake disc temperature were continuously monitored throughout the experiments. The results showed that the developed test rig provided stable and repeatable braking cycles. The coefficient of friction varied between 0.03 and 0.36, while the brake disc temperature gradually increased from approximately 60 °C to 80 °C during repeated braking cycles. The developed system successfully reproduced braking characteristics under the specified laboratory conditions and provides a practical, reliable, and cost-effective platform for brake performance evaluation and future friction material investigations.
- 31 May 2026
- Published by Uluslararasi Muhendislik Arastirma ve Gelistirme Dergisi in Uluslararası Muhendislik Arastirma ve Gelistirme Dergisi
- Vol. 18 (3) , 16-27
Experimental Investigation of the Effect of Air Filter Contamination on Exhaust Emissions in a Spark-Ignition Internal Combustion Engine
In this study, the effects of air filter contamination levels on exhaust emissions in a spark-ignition internal combustion engine were experimentally investigated. The experiments were conducted under three different air filter conditions: clean, moderately dirty, and dirty, and at engine speeds of approximately 1000, 2000, 3000, and 4000 min-1. As part of the experimental measurements, CO, HC, CO2, and O2 emissions were measured using an exhaust gas analyzer.Experimental results have shown that air filter contamination has a significant effect on emissions, particularly at low engine speeds. Under dirty air filter conditions, CO and HC emissions were found to increase by approximately 10-15% and 20-30%, respectively, at low and medium speeds. As engine speed increased, CO emissions decreased by approximately 45-60% and HC emissions decreased by approximately 40-50%, depending on the filter condition. CO2 emissions were found to increase with speed and reached values approximately 10% higher at 4000 min-1 under clean air filter conditions. In contrast, O2 emissions were found to decrease with increasing engine speed under all filter conditions. This demonstrates that air filter maintenance is a parameter that should be considered in terms of emission control and reducing environmental impacts under real-world operating conditions.
- 31 May 2026
- Published by Uluslararasi Muhendislik Arastirma ve Gelistirme Dergisi in Uluslararası Muhendislik Arastirma ve Gelistirme Dergisi
- Vol. 18 (3) , 16-27
Experimental Investigation of the Effect of Air Filter Contamination on Exhaust Emissions in a Spark-Ignition Internal Combustion Engine
In this study, the effects of air filter contamination levels on exhaust emissions in a spark-ignition internal combustion engine were experimentally investigated. The experiments were conducted under three different air filter conditions: clean, moderately dirty, and dirty, and at engine speeds of approximately 1000, 2000, 3000, and 4000 min-1. As part of the experimental measurements, CO, HC, CO2, and O2 emissions were measured using an exhaust gas analyzer.Experimental results have shown that air filter contamination has a significant effect on emissions, particularly at low engine speeds. Under dirty air filter conditions, CO and HC emissions were found to increase by approximately 10-15% and 20-30%, respectively, at low and medium speeds. As engine speed increased, CO emissions decreased by approximately 45-60% and HC emissions decreased by approximately 40-50%, depending on the filter condition. CO2 emissions were found to increase with speed and reached values approximately 10% higher at 4000 min-1 under clean air filter conditions. In contrast, O2 emissions were found to decrease with increasing engine speed under all filter conditions. This demonstrates that air filter maintenance is a parameter that should be considered in terms of emission control and reducing environmental impacts under real-world operating conditions.
- 21 January 2026
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (1) , 263-273
Experimental Analysis of Balance-Induced Vibrations in Vehicle Shafts
Extensive research has been conducted in recent years to mitigate damages caused by undesired vibrations in motor vehicles used for transportation. Vibrations occurring in highly active moving components of vehicles not only lead to discomfort in driving comfort but also reduce the material’s service life, causing fatigue and structural damage. Rotating elements in vehicles, such as the shaft (cardan shaft), crankshaft, and gears, can be sources of problems. In this study, vibrations resulting from an imbalance problem in the vehicle shaft were experimentally investigated, and the effects of balancing on the vehicle shaft were evaluated. For this purpose, vibration data were measured at three different points on a vehicle. Vibrations generated by the shaft under different road conditions and vehicle speeds were recorded and compared before and after balancing. The results of the study demonstrated a one-third reduction in vibration amplitude at the point beneath the driver's seat, which is directly associated with the comfort of both driver and passengers. Specifically, under the most demanding conditions (80 km·h⁻¹ speed and an uneven road surface), the vibration amplitude induced by the unbalanced driveshaft reached a high value of 2198 µm; after balancing, a reduction of approximately 65–70% in this amplitude was achieved at the measurement point under the driver's seat. In contrast, no significant difference was observed in the vibrations measured at the engine block and the luggage compartment. The findings indicate that vibrations originating from the vehicle driveshaft can be substantially mitigated through proper balancing.
- 21 January 2026
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (1) , 263-273
Experimental Analysis of Balance-Induced Vibrations in Vehicle Shafts
Extensive research has been conducted in recent years to mitigate damages caused by undesired vibrations in motor vehicles used for transportation. Vibrations occurring in highly active moving components of vehicles not only lead to discomfort in driving comfort but also reduce the material’s service life, causing fatigue and structural damage. Rotating elements in vehicles, such as the shaft (cardan shaft), crankshaft, and gears, can be sources of problems. In this study, vibrations resulting from an imbalance problem in the vehicle shaft were experimentally investigated, and the effects of balancing on the vehicle shaft were evaluated. For this purpose, vibration data were measured at three different points on a vehicle. Vibrations generated by the shaft under different road conditions and vehicle speeds were recorded and compared before and after balancing. The results of the study demonstrated a one-third reduction in vibration amplitude at the point beneath the driver's seat, which is directly associated with the comfort of both driver and passengers. Specifically, under the most demanding conditions (80 km·h⁻¹ speed and an uneven road surface), the vibration amplitude induced by the unbalanced driveshaft reached a high value of 2198 µm; after balancing, a reduction of approximately 65–70% in this amplitude was achieved at the measurement point under the driver's seat. In contrast, no significant difference was observed in the vibrations measured at the engine block and the luggage compartment. The findings indicate that vibrations originating from the vehicle driveshaft can be substantially mitigated through proper balancing.
- 31 December 2025
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 9 (4) , 618-625
Investigation of the Effect of Internal Combustion Engine Exhaust Gases on Workshop Air Quality and the Importance of Ventilation Systems
This study investigates the effect of exhaust gases emitted from a diesel engine operated on a workbench in the Motor Workshop of the Technical Sciences Vocational School at Karamanoğlu Mehmetbey University on the air quality of the workshop environment. The study also emphasizes the importance of using ventilation systems in such enclosed settings. In the experimental study, the concentrations of carbon monoxide (CO), carbon dioxide (CO₂), hydrocarbons (HC), nitrogen oxides (NOₓ) and benzene (C₆H₆) gases released into the workshop environment during engine operation were measured. The measurements were carried out in two different situations. In the first situation, an octopus-arm ventilation system was connected to the engine's exhaust manifold, while in the second situation, the ventilation system was not operated. The gas concentrations obtained in both situations were compared with the limit values specified in national and international occupational health and safety standards. The study found that when the ventilation system was operating, harmful gas levels remained below the limit values; however, when the ventilation was turned off, some gases, primarily CO and HC, exceeded the short-term exposure limits. These findings demonstrate that the use of effective ventilation systems in engine operation applications is critical for occupational health and safety
- 31 December 2025
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 9 (4) , 618-625
Investigation of the Effect of Internal Combustion Engine Exhaust Gases on Workshop Air Quality and the Importance of Ventilation Systems
This study investigates the effect of exhaust gases emitted from a diesel engine operated on a workbench in the Motor Workshop of the Technical Sciences Vocational School at Karamanoğlu Mehmetbey University on the air quality of the workshop environment. The study also emphasizes the importance of using ventilation systems in such enclosed settings. In the experimental study, the concentrations of carbon monoxide (CO), carbon dioxide (CO₂), hydrocarbons (HC), nitrogen oxides (NOₓ) and benzene (C₆H₆) gases released into the workshop environment during engine operation were measured. The measurements were carried out in two different situations. In the first situation, an octopus-arm ventilation system was connected to the engine's exhaust manifold, while in the second situation, the ventilation system was not operated. The gas concentrations obtained in both situations were compared with the limit values specified in national and international occupational health and safety standards. The study found that when the ventilation system was operating, harmful gas levels remained below the limit values; however, when the ventilation was turned off, some gases, primarily CO and HC, exceeded the short-term exposure limits. These findings demonstrate that the use of effective ventilation systems in engine operation applications is critical for occupational health and safety
- 20 July 2025
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 27 (1) , 429-439
Performance Analysis of Rectifier Circuits for Claw-Pole Synchronous Generators: A Comparative Simulation
- 20 July 2025
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 27 (1) , 429-439
Performance Analysis of Rectifier Circuits for Claw-Pole Synchronous Generators: A Comparative Simulation
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 57 (4) , 485-501
Investigation of microstructural and tribological properties of a commercial brake pad
In this study, micro and macro characterization of commercial brake pad by SEM, EDX, XRD and FTIR tests and determination of braking performance according to SAE J661 Test Procedure were aimed. The microstructure and spectrographic properties of the pad were compared with wear, density, surface roughness and hardness tests. In the study, it was determined that fibers, iron powders, oxides, vermiculite, graphite, barite and resin were homogeneously distributed in the microstructure and confirmed by the presence of :29 elements by EDX analysis. X-ray diffraction analysis revealed different morphologies and crystal forms in the test sample. The interaction of organic and inorganic compounds and functional groups of different elements were studied by FTIR analysis. In braking tests, the highest hot and cold coefficients of friction were 0.48 and 0.58, respectively, and the pad quality was determined as class G.
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 57 (4) , 485-501
Open AccessInvestigation of microstructural and tribological properties of a commercial brake pad
In this study, micro and macro characterization of commercial brake pad by SEM, EDX, XRD and FTIR tests and determination of braking performance according to SAE J661 Test Procedure were aimed. The microstructure and spectrographic properties of the pad were compared with wear, density, surface roughness and hardness tests. In the study, it was determined that fibers, iron powders, oxides, vermiculite, graphite, barite and resin were homogeneously distributed in the microstructure and confirmed by the presence of :29 elements by EDX analysis. X-ray diffraction analysis revealed different morphologies and crystal forms in the test sample. The interaction of organic and inorganic compounds and functional groups of different elements were studied by FTIR analysis. In braking tests, the highest hot and cold coefficients of friction were 0.48 and 0.58, respectively, and the pad quality was determined as class G.
- Open Access
- 3 September 2023
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 26 (3) , 694-706
TARIMSAL TRAKTÖRLERLE YAPILAN YOL İÇİ TAŞIMACILIKTA KULLANICI BÖLÜMÜ YAPISININ HAVA AKIŞI DİRENCİ AÇISINDAN DENEYSEL İNCELENMESİ
Bu çalışmada bir rüzgâr tüneli kullanılarak ölçeklendirilmiş tarımsal traktör modellerine etki eden hava akışı direnci deneysel olarak tespit edilmiştir. Traktör modelleri aynı şekle sahiptir fakat kullanıcının bulunduğu bölümde üç farklı tasarım denenmiştir. Bunlar kabinle kuşatılmış platform, güneşlikli platform ve devrilme sırasında kullanıcıyı koruyacak koruma çubuklu platformdur. Böylece kullanıcı bölümünün tasarımına bağlı olarak yol içi taşımacılıkta traktörlerin maruz kaldığı hava direnci değişimleri ilk defa deneysel olarak belirlenmiş olmaktadır. Geometrik benzerlik esaslarına göre rüzgâr tünelinde kullanılan traktör modelleri 1:13 oranında hazırlanmıştır. Rüzgâr tüneli testlerinde kinematik ve dinamik benzerlik sağlanamamakta fakat Reynolds sayısı bağımsızlığı elde edilebilmektedir. Rüzgâr tüneli hava akış hızı aralığında farklı hava hızlarında deneyler yapılarak bir Reynolds sayısı aralığı taranmıştır. Bu aralıkta modellere etki eden aerodinamik direnç kuvvetleri ve traktörlerin simetri ekseninde hava akışı kaynaklı basınç dağılımları ölçülmüştür. Elde edilen ölçümlerden boyutsuz aerodinamik direnç katsayısı ve basınç katsayısı değerleri hesaplanmıştır. Hesaplamalara göre kabin kullanımı aerodinamik direnci %3-15 aralığında arttırmaktadır. Düşük hızlarda kabin kullanımı kaynaklı direnç artış yüzdesi fazlayken yüksek hızlarda azalmaktadır. Kabin kullanımı sonucunda akışa dik traktör ön izdüşüm alanı artmaktadır. Fakat aerodinamik dirençteki artış ön iz düşüm alanındaki artışa göre bir mertebe daha düşüktür. Kabin kullanımının iş güvenliği açısından sağladıkları da düşünüldüğünde kabin kullanımı kaynaklı aerodinamik direnç artışının kabul edilebilir bir maliyet olduğu anlaşılmaktadır. Çalışma sonuçlarının tarımsal traktörlerle yol içi taşımacılıkta enerji tüketiminin ayrıştırılmasına katkı sağlaması beklenmektedir.
- 3 September 2023
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 26 (3) , 694-706
Open AccessTARIMSAL TRAKTÖRLERLE YAPILAN YOL İÇİ TAŞIMACILIKTA KULLANICI BÖLÜMÜ YAPISININ HAVA AKIŞI DİRENCİ AÇISINDAN DENEYSEL İNCELENMESİ
Bu çalışmada bir rüzgâr tüneli kullanılarak ölçeklendirilmiş tarımsal traktör modellerine etki eden hava akışı direnci deneysel olarak tespit edilmiştir. Traktör modelleri aynı şekle sahiptir fakat kullanıcının bulunduğu bölümde üç farklı tasarım denenmiştir. Bunlar kabinle kuşatılmış platform, güneşlikli platform ve devrilme sırasında kullanıcıyı koruyacak koruma çubuklu platformdur. Böylece kullanıcı bölümünün tasarımına bağlı olarak yol içi taşımacılıkta traktörlerin maruz kaldığı hava direnci değişimleri ilk defa deneysel olarak belirlenmiş olmaktadır. Geometrik benzerlik esaslarına göre rüzgâr tünelinde kullanılan traktör modelleri 1:13 oranında hazırlanmıştır. Rüzgâr tüneli testlerinde kinematik ve dinamik benzerlik sağlanamamakta fakat Reynolds sayısı bağımsızlığı elde edilebilmektedir. Rüzgâr tüneli hava akış hızı aralığında farklı hava hızlarında deneyler yapılarak bir Reynolds sayısı aralığı taranmıştır. Bu aralıkta modellere etki eden aerodinamik direnç kuvvetleri ve traktörlerin simetri ekseninde hava akışı kaynaklı basınç dağılımları ölçülmüştür. Elde edilen ölçümlerden boyutsuz aerodinamik direnç katsayısı ve basınç katsayısı değerleri hesaplanmıştır. Hesaplamalara göre kabin kullanımı aerodinamik direnci %3-15 aralığında arttırmaktadır. Düşük hızlarda kabin kullanımı kaynaklı direnç artış yüzdesi fazlayken yüksek hızlarda azalmaktadır. Kabin kullanımı sonucunda akışa dik traktör ön izdüşüm alanı artmaktadır. Fakat aerodinamik dirençteki artış ön iz düşüm alanındaki artışa göre bir mertebe daha düşüktür. Kabin kullanımının iş güvenliği açısından sağladıkları da düşünüldüğünde kabin kullanımı kaynaklı aerodinamik direnç artışının kabul edilebilir bir maliyet olduğu anlaşılmaktadır. Çalışma sonuçlarının tarımsal traktörlerle yol içi taşımacılıkta enerji tüketiminin ayrıştırılmasına katkı sağlaması beklenmektedir.
- 24 August 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (3) , 6658-6680
Impact assessment of new generation high-speed agricultural tractor aerodynamics on transportation fuel consumption and related phenomena
New generation agricultural tractors contribute to transportation by increased travel speeds. There is not any available aerodynamic data on the authentic agricultural tractor form. On-road transportation by tractors is between 8 and 30% of their operational time. In this work, two agricultural tractors are modelled via computational fluid dynamics for nine different speeds to determine aerodynamic resistances. Constant speed travel scenarios are analyzed. Corresponding speeds are 5 and 10 to 80 km/h with 10 km/h increments. Reynolds number changes between 1.6 × 105 and 2.98 × 106. The characteristic lengths are taken as the square root of the streamwise projected area of the tractor geometries. Aerodynamic forces exerted on the tractors change between 3 and 746 N. The calculated drag coefficients are found as independent from Reynolds number and are 0.6 and 0.78 for the two different types of driver compartments. The approximated aerodynamic related fuel consumptions for 1-h changes between 0.002 and 8.28 lt/s which correspond to 0.001 to 5.76 kg/s carbon emission. A potential improvement in decreasing aerodynamic resistance about 20% is discussed by spatial data. Since the conducted work is being regarded as the first instance in the literature, it is estimated that several consecutive reports will be triggered.
- 24 August 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (3) , 6658-6680
Impact assessment of new generation high-speed agricultural tractor aerodynamics on transportation fuel consumption and related phenomena
New generation agricultural tractors contribute to transportation by increased travel speeds. There is not any available aerodynamic data on the authentic agricultural tractor form. On-road transportation by tractors is between 8 and 30% of their operational time. In this work, two agricultural tractors are modelled via computational fluid dynamics for nine different speeds to determine aerodynamic resistances. Constant speed travel scenarios are analyzed. Corresponding speeds are 5 and 10 to 80 km/h with 10 km/h increments. Reynolds number changes between 1.6 × 105 and 2.98 × 106. The characteristic lengths are taken as the square root of the streamwise projected area of the tractor geometries. Aerodynamic forces exerted on the tractors change between 3 and 746 N. The calculated drag coefficients are found as independent from Reynolds number and are 0.6 and 0.78 for the two different types of driver compartments. The approximated aerodynamic related fuel consumptions for 1-h changes between 0.002 and 8.28 lt/s which correspond to 0.001 to 5.76 kg/s carbon emission. A potential improvement in decreasing aerodynamic resistance about 20% is discussed by spatial data. Since the conducted work is being regarded as the first instance in the literature, it is estimated that several consecutive reports will be triggered.
- 31 December 2021
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 5 (4) , 436-444
Prediction of Specific Fuel Consumption of 60 HP 2WD Tractor Using Artificial Neural Networks
In this study, specific fuel consumption was determined at different axle load, tire pressure and drawbar force for a 60 HP tractor. In addition, the results were also estimated with the help of Artificial Neural Networks (ANN), which is one of the machine learning methods. The testings were carried out on the Tractor Draft Test Track. In the study; three different drive tire inner pressures (P) (160 kPa, 120 kPa and 80 kPa), four different dynamic axle loads (W) (1796 daN, 2076 daN, 2276 daN, 2476 daN) and four different traction forces (500 daN,1000 daN, 1500 daN, 2000 daN) were tested. Specific fuel consump-tion values varied between 290.7-542.1 g/kWh depending on the draft force in the testings Despite the 38% increase in the axle load, a 3.5% decrease occurred in the specific fuel consumption values. Specific fuel consumption values in-creased when increased tire inner pressure. Specific fuel consumption in-creased by 1.03% when a 100% increase in tire pressure. In ANN, the most suc-cessful model was determined by trying different training algorithms, transfer functions and the number of neurons in the hidden layer. In the most successful network model, MAE, RMSE values for the prediction of specific fuel consump-tion were found to be 0.005331, 0.007551 respectively.
- 31 December 2021
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 5 (4) , 436-444
Prediction of Specific Fuel Consumption of 60 HP 2WD Tractor Using Artificial Neural Networks
In this study, specific fuel consumption was determined at different axle load, tire pressure and drawbar force for a 60 HP tractor. In addition, the results were also estimated with the help of Artificial Neural Networks (ANN), which is one of the machine learning methods. The testings were carried out on the Tractor Draft Test Track. In the study; three different drive tire inner pressures (P) (160 kPa, 120 kPa and 80 kPa), four different dynamic axle loads (W) (1796 daN, 2076 daN, 2276 daN, 2476 daN) and four different traction forces (500 daN,1000 daN, 1500 daN, 2000 daN) were tested. Specific fuel consump-tion values varied between 290.7-542.1 g/kWh depending on the draft force in the testings Despite the 38% increase in the axle load, a 3.5% decrease occurred in the specific fuel consumption values. Specific fuel consumption values in-creased when increased tire inner pressure. Specific fuel consumption in-creased by 1.03% when a 100% increase in tire pressure. In ANN, the most suc-cessful model was determined by trying different training algorithms, transfer functions and the number of neurons in the hidden layer. In the most successful network model, MAE, RMSE values for the prediction of specific fuel consump-tion were found to be 0.005331, 0.007551 respectively.