İbRahim Mutlu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
İbRahim Mutlu has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Bekir Güney
Karamanoglu Mehmetbey University
5 shared publications - Furkan Akbulut
Hitit Üniversitesi , Department of Motor Vehicles and Transportation Technology, Çorum, Türkiye
5 shared publications - İbRahim Yavuz
Afyon Kocatepe University
3 shared publications - Faruk Emre Aysal
Department of Mechanical Engineering, Faculty of Engineering, Giresun University, 28200 Giresun, Türkiye
2 shared publications - Hanifi Küçüksarıyıldız
Karamanoğlu Mehmetbey Üniversitesi
2 shared publications - Mustafa Arikan
Afyon Kocatepe University
2 shared publications
Latest Publications
- 7 August 2026
- Published by Elsevier in Next Research
- Vol. 12
Evaluation of passenger car brake disc performance criteria using the WASPAS multi-criteria decision-making technique
- 7 August 2026
- Published by Elsevier in Next Research
- Vol. 12
Evaluation of passenger car brake disc performance criteria using the WASPAS multi-criteria decision-making technique
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Experimental and numerical analysis of the effect of strut orientation on the bending and compression behavior of FBCCZ lattice structure
In this study, the mechanical behavior and energy absorption performance of FBCCZ and FBCCY lattice structures with identical relative density were investigated experimentally and numerically under compression and three-point bending loading conditions. The lattice specimens were fabricated using stereolithography and subjected to compression and bending experiments according to ASTM standards. Finite element analyses were performed using ANSYS Static Structural and LS-DYNA solvers, and a mesh convergence study was conducted to verify the reliability of the numerical model. The experimental and numerical results demonstrated that strut orientation significantly affects deformation behavior, load-carrying capacity, and energy absorption capability of the lattice structures. Under compressive loading, FBCCZ-oriented specimens exhibited approximately 30.9% higher experimental energy absorption and 33.4% higher numerical energy absorption compared to FBCCY-oriented specimens. In contrast, FBCCY-oriented structures demonstrated superior load-carrying and energy absorption behavior under three-point bending conditions. Different collapse mechanisms were also observed depending on strut orientation; collapse initiated from the top region in FBCCY structures, whereas deformation began from the bottom region in FBCCZ structures. The numerical analyses showed good agreement with the experimental results under both loading conditions. The results indicate that strut orientation should be considered a crucial design parameter for lightweight lattice structures under different loading conditions.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Open AccessExperimental and numerical analysis of the effect of strut orientation on the bending and compression behavior of FBCCZ lattice structure
In this study, the mechanical behavior and energy absorption performance of FBCCZ and FBCCY lattice structures with identical relative density were investigated experimentally and numerically under compression and three-point bending loading conditions. The lattice specimens were fabricated using stereolithography and subjected to compression and bending experiments according to ASTM standards. Finite element analyses were performed using ANSYS Static Structural and LS-DYNA solvers, and a mesh convergence study was conducted to verify the reliability of the numerical model. The experimental and numerical results demonstrated that strut orientation significantly affects deformation behavior, load-carrying capacity, and energy absorption capability of the lattice structures. Under compressive loading, FBCCZ-oriented specimens exhibited approximately 30.9% higher experimental energy absorption and 33.4% higher numerical energy absorption compared to FBCCY-oriented specimens. In contrast, FBCCY-oriented structures demonstrated superior load-carrying and energy absorption behavior under three-point bending conditions. Different collapse mechanisms were also observed depending on strut orientation; collapse initiated from the top region in FBCCY structures, whereas deformation began from the bottom region in FBCCZ structures. The numerical analyses showed good agreement with the experimental results under both loading conditions. The results indicate that strut orientation should be considered a crucial design parameter for lightweight lattice structures under different loading conditions.
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 57 (4) , 485-501
Investigation of microstructural and tribological properties of a commercial brake pad
In this study, micro and macro characterization of commercial brake pad by SEM, EDX, XRD and FTIR tests and determination of braking performance according to SAE J661 Test Procedure were aimed. The microstructure and spectrographic properties of the pad were compared with wear, density, surface roughness and hardness tests. In the study, it was determined that fibers, iron powders, oxides, vermiculite, graphite, barite and resin were homogeneously distributed in the microstructure and confirmed by the presence of :29 elements by EDX analysis. X-ray diffraction analysis revealed different morphologies and crystal forms in the test sample. The interaction of organic and inorganic compounds and functional groups of different elements were studied by FTIR analysis. In braking tests, the highest hot and cold coefficients of friction were 0.48 and 0.58, respectively, and the pad quality was determined as class G.
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 57 (4) , 485-501
Open AccessInvestigation of microstructural and tribological properties of a commercial brake pad
In this study, micro and macro characterization of commercial brake pad by SEM, EDX, XRD and FTIR tests and determination of braking performance according to SAE J661 Test Procedure were aimed. The microstructure and spectrographic properties of the pad were compared with wear, density, surface roughness and hardness tests. In the study, it was determined that fibers, iron powders, oxides, vermiculite, graphite, barite and resin were homogeneously distributed in the microstructure and confirmed by the presence of :29 elements by EDX analysis. X-ray diffraction analysis revealed different morphologies and crystal forms in the test sample. The interaction of organic and inorganic compounds and functional groups of different elements were studied by FTIR analysis. In braking tests, the highest hot and cold coefficients of friction were 0.48 and 0.58, respectively, and the pad quality was determined as class G.
- Open Access
- 30 December 2024
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 14 (2) , 59-66
The impact of mixed fuels containing pyrolysis oil, diesel, n-butanol and 2-EHN on emissions and performance of diesel engine
The environmental impactof fossil fuels and their limited availability increase the need for research into alternative energy sources. In this research, pyrolysis oil (PO) was obtained from waste sour cherry kernels. PO cannot be used directly as fuel in diesel engines because of its negative fuel properties, such as low energy density, high viscosity, high water content, and low cetane number. Therefore, PO was blended with diesel at various weight proportions (wt%) using n-butanol (NB) as cosolvent, and 2-ethylhexyl nitrate (2-EHN) as cetane improver. Blended fuels containing 40 wt% diesel i.e., D2 (Diesel 40% / PO 0% / NB 55% / 2-EHN %5), D3 (Diesel 40 / PO 5% / NB 50% / 2-EHN 5%) and D4 (Diesel 40% / PO 15% / NB 40% / 2-EHN 5%) were identified as optimal blend compositions regarding the physicochemical characteristics of fuel. These fuels were tested for engine performance and emission characteristics at engine speeds of 1500, 1800, 2400, 3000 and 3600 rpm under full engine load (10 Nm) in a single-cylinder diesel engine. All data (i.e. cylinder pressure, engine torque and performance changes, heat release rate, and emission characteristics) were recorded using a Kistler KiBox data acquisition system. The engine tests showed a decrease in NOx, HC and soot emissions when blended fuels (D2, D3 and D4) were compared to D1 (Diesel 100% / PO 0% / NB 0% / 2-EHN 0%). The lower NOx emissions in the blended fuels are explained by the PO's water content. Water raises the specific heat capacity of the fuel-air mixture while reducing the internal cylinder temperature. Additionally, the high latent heat of evaporation of n-butanol may contribute to reduce NOx emissions. In addition, the decrease in HC emissions may be caused by the increase in the oxygen ratio of blended fuels, while the decrease in soot emissions may be caused by the low C/H ratio and high oxygen content of blended fuels. To conclude, blends of PO, diesel n-butanol, and 2-EHN can be used as biofuels in diesel engine applications.
- 30 December 2024
- Published by Instituto Colombiano del Petroleo in Ct&f - Ciencia, Tecnología Y Futuro
- Vol. 14 (2) , 59-66
Open AccessThe impact of mixed fuels containing pyrolysis oil, diesel, n-butanol and 2-EHN on emissions and performance of diesel engine
The environmental impactof fossil fuels and their limited availability increase the need for research into alternative energy sources. In this research, pyrolysis oil (PO) was obtained from waste sour cherry kernels. PO cannot be used directly as fuel in diesel engines because of its negative fuel properties, such as low energy density, high viscosity, high water content, and low cetane number. Therefore, PO was blended with diesel at various weight proportions (wt%) using n-butanol (NB) as cosolvent, and 2-ethylhexyl nitrate (2-EHN) as cetane improver. Blended fuels containing 40 wt% diesel i.e., D2 (Diesel 40% / PO 0% / NB 55% / 2-EHN %5), D3 (Diesel 40 / PO 5% / NB 50% / 2-EHN 5%) and D4 (Diesel 40% / PO 15% / NB 40% / 2-EHN 5%) were identified as optimal blend compositions regarding the physicochemical characteristics of fuel. These fuels were tested for engine performance and emission characteristics at engine speeds of 1500, 1800, 2400, 3000 and 3600 rpm under full engine load (10 Nm) in a single-cylinder diesel engine. All data (i.e. cylinder pressure, engine torque and performance changes, heat release rate, and emission characteristics) were recorded using a Kistler KiBox data acquisition system. The engine tests showed a decrease in NOx, HC and soot emissions when blended fuels (D2, D3 and D4) were compared to D1 (Diesel 100% / PO 0% / NB 0% / 2-EHN 0%). The lower NOx emissions in the blended fuels are explained by the PO's water content. Water raises the specific heat capacity of the fuel-air mixture while reducing the internal cylinder temperature. Additionally, the high latent heat of evaporation of n-butanol may contribute to reduce NOx emissions. In addition, the decrease in HC emissions may be caused by the increase in the oxygen ratio of blended fuels, while the decrease in soot emissions may be caused by the low C/H ratio and high oxygen content of blended fuels. To conclude, blends of PO, diesel n-butanol, and 2-EHN can be used as biofuels in diesel engine applications.
- Open Access
- 30 June 2024
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 8 (2) , 167-178
Experimental Comparison of Manufacturing Parameters in Automotive Friction Materials
In this study, a fixed automotive friction material content was determined and the mechanical and tribological effects of manufacturing parameters on friction materials were investigated. Parameters; pre-forming time (1-3-5 min) and pre-forming pressure (8-10-12 MPa), hot pressing time (5-10-15 min) hot pressing pressure (8-10-12 MPa) and hot pressing temperature (125-150-175 °C), curing time (4-8-12 h) and curing temperature (120-150-180 °C) were determined. The friction test of the produced samples was carried out under 0.551 MPa pressure and 7 m/s rotation speed for 90 min. In addition, the average COF, friction stability, specific wear rate, density and hardness values of the samples were calculated. According to the results obtained, the average COF value increased as the pre-forming time and pressure increased. The lowest specific wear rate among all specimens was calculated as 7.622x10-6 cm3/Nm in PFP-12 specimen. With the increase in hot pressing time, the tribological properties of friction materials improved. The highest friction stability among all samples was calculated as 79.42% in the HPT-15 sample. Although there was an increase in the average COF value with increasing hot pressing pressure and temperature, the specific wear rates increased in these parameters. The highest average COF value among all samples was obtained in the CT-12 sample with a value of 0.553. The specific wear rate increased with the increase in curing time and temperature. The highest specific wear rate among all samples was calculated 10,743x10-6 cm3/Nm in the CTe-180 sample. Finally, it has been suggested that 3 min for pre-forming time, 12 MPa for pre-forming pressure; 15 min for hot pressing time, 12 MPa for hot pressing pressure, and 150°C for hot pressing temperature; and a curing time of 8 h and curing temperature of 150 °C may be sufficient.
- 30 June 2024
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 8 (2) , 167-178
Open AccessExperimental Comparison of Manufacturing Parameters in Automotive Friction Materials
In this study, a fixed automotive friction material content was determined and the mechanical and tribological effects of manufacturing parameters on friction materials were investigated. Parameters; pre-forming time (1-3-5 min) and pre-forming pressure (8-10-12 MPa), hot pressing time (5-10-15 min) hot pressing pressure (8-10-12 MPa) and hot pressing temperature (125-150-175 °C), curing time (4-8-12 h) and curing temperature (120-150-180 °C) were determined. The friction test of the produced samples was carried out under 0.551 MPa pressure and 7 m/s rotation speed for 90 min. In addition, the average COF, friction stability, specific wear rate, density and hardness values of the samples were calculated. According to the results obtained, the average COF value increased as the pre-forming time and pressure increased. The lowest specific wear rate among all specimens was calculated as 7.622x10-6 cm3/Nm in PFP-12 specimen. With the increase in hot pressing time, the tribological properties of friction materials improved. The highest friction stability among all samples was calculated as 79.42% in the HPT-15 sample. Although there was an increase in the average COF value with increasing hot pressing pressure and temperature, the specific wear rates increased in these parameters. The highest average COF value among all samples was obtained in the CT-12 sample with a value of 0.553. The specific wear rate increased with the increase in curing time and temperature. The highest specific wear rate among all samples was calculated 10,743x10-6 cm3/Nm in the CTe-180 sample. Finally, it has been suggested that 3 min for pre-forming time, 12 MPa for pre-forming pressure; 15 min for hot pressing time, 12 MPa for hot pressing pressure, and 150°C for hot pressing temperature; and a curing time of 8 h and curing temperature of 150 °C may be sufficient.
- Open Access
- 31 December 2023
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 7 (4) , 309-315
Investigation of Tribological Properties of Brake Friction Materials Developed from Industrial Waste Products
Various international initiatives on environmental issues and the need to protect the environment are promoting the use of industrial waste in a variety of applications, including automotive brake pads. These studies show that the reuse of industrial waste can help to reduce the environmental impact. The development of environmentally friendly and cost-effective composites for use in a variety of engineering applications is the need of the century. The use of industrial waste in composite production is a possible solution for both problems. In this study, the potential use of talc, quartz and ceramic waste FFC fracture as a friction modifier in brake friction materials and its performance properties in accordance with industry requirements were investigated. The tribological, physical and mechanical properties of the brake pads were measured, and the friction surface morphology was investigated by scanning electron microscopy. According to the results obtained, the highest specific wear rate was observed in the FM3 sample. The FM2 sample with the highest hardness and average friction coefficient showed the lowest wear. FM4, FM5 and FM6 samples with high talc and quartz content exhibited low coefficient of friction characteristics compared to other samples.
- 31 December 2023
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 7 (4) , 309-315
Open AccessInvestigation of Tribological Properties of Brake Friction Materials Developed from Industrial Waste Products
Various international initiatives on environmental issues and the need to protect the environment are promoting the use of industrial waste in a variety of applications, including automotive brake pads. These studies show that the reuse of industrial waste can help to reduce the environmental impact. The development of environmentally friendly and cost-effective composites for use in a variety of engineering applications is the need of the century. The use of industrial waste in composite production is a possible solution for both problems. In this study, the potential use of talc, quartz and ceramic waste FFC fracture as a friction modifier in brake friction materials and its performance properties in accordance with industry requirements were investigated. The tribological, physical and mechanical properties of the brake pads were measured, and the friction surface morphology was investigated by scanning electron microscopy. According to the results obtained, the highest specific wear rate was observed in the FM3 sample. The FM2 sample with the highest hardness and average friction coefficient showed the lowest wear. FM4, FM5 and FM6 samples with high talc and quartz content exhibited low coefficient of friction characteristics compared to other samples.
- 27 September 2023
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 11 (3) , 673-684
Investigation of Measurement Accuracy of Chassis Dynamometers Used in Used Automotive Sector
Şasi dinamometreleri motor, güç aktarma organları ve şasi bileşenlerinin test edilmesi amacıyla kullanılmaktadır. Taşıt tipi, boyutları ve ağırlığı gibi temel faktörlerin yanı sıra test cihazı yapısı, yazılımı ve ölçüm yöntemlerine göre sistem üzerinde farklı parametreler incelenebilmektedir. Test sistemi üzerinde kullanılan ekipman ve tasarım yapısına bağlı olarak ölçüm hassasiyeti değişmektedir. Günümüzde ikinci el araç kontrollerinde oto ekspertiz firmaları tarafından yaygın olarak gerçekleştirilen şasi dinamometre testlerinin doğruluğu ve güvenilirliği bir tartışma konusudur. Bu çalışmada, piyasada kullanılan şasi dinamometrelerinin ölçüm doğruluklarının araştırılması için üç farklı taşıt, iki farklı oto ekspertiz firmasında test edilmiştir. Testlerde common rail yakıt enjeksiyonuna sahip, turboşarjlı, Euro 5 emisyon normlarına uygun dizel motora ve manuel vites kutusuna sahip taşıtlar kullanılmıştır. Şasi dinamometrelerinde gerçekleştirilen tüm testlerde belirlenen standart adımlar izlenmiş olup testler basınç ve sıcaklık kaynaklı sapmaların önlenmesi için aynı lokasyondaki firmalarda gerçekleştirilmiştir. Test sonuçlarında taşıtlara ait maksimum güç ve maksimum güç devri, maksimum tork ve maksimum tork devri, ayrıca bu değerlerin fabrika verilerinden sapma miktarları elde edilmiştir. Firmalara ait test sonuçları kendi arasında ve fabrika verileri ile karşılaştırıldığında güç-tork eğrileri, maksimum güç-tork değerleri ve bu değerlerin ortaya çıktığı motor devirlerinde önemli ölçüde sapmalar oluştuğu tespit edilmiştir.
- 27 September 2023
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 11 (3) , 673-684
Investigation of Measurement Accuracy of Chassis Dynamometers Used in Used Automotive Sector
Şasi dinamometreleri motor, güç aktarma organları ve şasi bileşenlerinin test edilmesi amacıyla kullanılmaktadır. Taşıt tipi, boyutları ve ağırlığı gibi temel faktörlerin yanı sıra test cihazı yapısı, yazılımı ve ölçüm yöntemlerine göre sistem üzerinde farklı parametreler incelenebilmektedir. Test sistemi üzerinde kullanılan ekipman ve tasarım yapısına bağlı olarak ölçüm hassasiyeti değişmektedir. Günümüzde ikinci el araç kontrollerinde oto ekspertiz firmaları tarafından yaygın olarak gerçekleştirilen şasi dinamometre testlerinin doğruluğu ve güvenilirliği bir tartışma konusudur. Bu çalışmada, piyasada kullanılan şasi dinamometrelerinin ölçüm doğruluklarının araştırılması için üç farklı taşıt, iki farklı oto ekspertiz firmasında test edilmiştir. Testlerde common rail yakıt enjeksiyonuna sahip, turboşarjlı, Euro 5 emisyon normlarına uygun dizel motora ve manuel vites kutusuna sahip taşıtlar kullanılmıştır. Şasi dinamometrelerinde gerçekleştirilen tüm testlerde belirlenen standart adımlar izlenmiş olup testler basınç ve sıcaklık kaynaklı sapmaların önlenmesi için aynı lokasyondaki firmalarda gerçekleştirilmiştir. Test sonuçlarında taşıtlara ait maksimum güç ve maksimum güç devri, maksimum tork ve maksimum tork devri, ayrıca bu değerlerin fabrika verilerinden sapma miktarları elde edilmiştir. Firmalara ait test sonuçları kendi arasında ve fabrika verileri ile karşılaştırıldığında güç-tork eğrileri, maksimum güç-tork değerleri ve bu değerlerin ortaya çıktığı motor devirlerinde önemli ölçüde sapmalar oluştuğu tespit edilmiştir.
- Open Access
- 30 March 2023
- Published by International Journal of Automotive Engineering and Technologies in International Journal of Automotive Engineering and Technologies
- Vol. 12 (1) , 16-21
The effect of sintering time on the tribological properties of automotive brake pads
In this study, the effect of sintering temperature on the physical, chemical and tribological effects of sintered automotive friction materials was investigated. Using the powder metallurgy method, 3 different samples were produced with the codes A1, A6 and A11. Mixing, pressing and sintering processes were applied respectively as production steps. Mixing time is 90 minutes, speed is 15 rpm. The pressing pressure is 250 MPa and the duration is 1 min. The sintering temperature was 800 °C and the sintering time was 1, 6 and 11 hours, respectively. The sintering process was carried out in the sintering mold using Argon gas. As the sintering time increased, it was observed that there was an increase in the time-dependent friction coefficients of the samples. Increasing the sintering time also increased the density of the samples. As the sintering time increased, the gap in the sample decreased, as it provided better bonding of the dustsers.
- 30 March 2023
- Published by International Journal of Automotive Engineering and Technologies in International Journal of Automotive Engineering and Technologies
- Vol. 12 (1) , 16-21
Open AccessThe effect of sintering time on the tribological properties of automotive brake pads
In this study, the effect of sintering temperature on the physical, chemical and tribological effects of sintered automotive friction materials was investigated. Using the powder metallurgy method, 3 different samples were produced with the codes A1, A6 and A11. Mixing, pressing and sintering processes were applied respectively as production steps. Mixing time is 90 minutes, speed is 15 rpm. The pressing pressure is 250 MPa and the duration is 1 min. The sintering temperature was 800 °C and the sintering time was 1, 6 and 11 hours, respectively. The sintering process was carried out in the sintering mold using Argon gas. As the sintering time increased, it was observed that there was an increase in the time-dependent friction coefficients of the samples. Increasing the sintering time also increased the density of the samples. As the sintering time increased, the gap in the sample decreased, as it provided better bonding of the dustsers.
- 30 June 2022
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 6 (2) , 172-177
Investigation of the Effect of Side Mirror Forms on Ahmed Body with CFD Method
The purpose of this study is to investigate the air resistance effect of different side mir-ror models on automobiles. The Ahmed Body model with 250 slant angle is taken as ref-erence for use as automobile geometry. Ahmed body is a simplified geometry model used for aerodynamic analysis of land vehicles. Side mirror models with the same front projection area were modeled using Solidworks. CFD simulation was performed with ANSYS Fluent 19.2. Realizable k-ε model is used as turbulence model and pressure-based type is used as solver type. In this study, the mesh quality was checked in terms of skewness and showed conformity. CD value obtained by numerical analysis is compati-ble with experimental data. Then, a comparison was made by adding side mirrors to the Ahmed Body model. As a result of the analysis, the display of the velocity and pressure distribution caused by the change of form around the mirror models and total CD values were determined.
- 30 June 2022
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 6 (2) , 172-177
Investigation of the Effect of Side Mirror Forms on Ahmed Body with CFD Method
The purpose of this study is to investigate the air resistance effect of different side mir-ror models on automobiles. The Ahmed Body model with 250 slant angle is taken as ref-erence for use as automobile geometry. Ahmed body is a simplified geometry model used for aerodynamic analysis of land vehicles. Side mirror models with the same front projection area were modeled using Solidworks. CFD simulation was performed with ANSYS Fluent 19.2. Realizable k-ε model is used as turbulence model and pressure-based type is used as solver type. In this study, the mesh quality was checked in terms of skewness and showed conformity. CD value obtained by numerical analysis is compati-ble with experimental data. Then, a comparison was made by adding side mirrors to the Ahmed Body model. As a result of the analysis, the display of the velocity and pressure distribution caused by the change of form around the mirror models and total CD values were determined.
- 1 September 2021
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 10 (3) , 314-320
The ANN analysis and Taguchi method optimisation of the brake pad composition
In this study, the Taguchi optimisation technique was utilised to establish the composition of an asbestos-free brake pad. As a result of optimisation outputs, 18 various compositions were obtained. The produced specimens according to outputs were subjected to friction assessment and screening tests to evaluate their average friction coefficient and friction surface temperature. By assessing the results, the composition of brake pads, which can be used in vehicle brakes, was determined. The experimental results were also examined by variance analysis to demonstrate effect factors. Furthermore, when the test results were evaluated in terms of the friction coefficient, wear rate and temperature of the brake disc, a high coefficient of friction, a moderate wear rate and an acceptable temperature of the brake disc were obtained in sample 13. The composition of sample 13, which has the highest friction coefficient, is 3 g brass powder, 9 g cashew, 9 g carbon fibre, 9 g copper dust and 9 g graphite. Lastly, the average friction coefficients of brake pads were estimated through artificial neural network (ANN) analysis. With respect to the results, it was discovered that the generated ANN model promises a high ratio estimation capacity.
- 1 September 2021
- Published by Emerald Publishing in Emerging Materials Research
- Vol. 10 (3) , 314-320
The ANN analysis and Taguchi method optimisation of the brake pad composition
In this study, the Taguchi optimisation technique was utilised to establish the composition of an asbestos-free brake pad. As a result of optimisation outputs, 18 various compositions were obtained. The produced specimens according to outputs were subjected to friction assessment and screening tests to evaluate their average friction coefficient and friction surface temperature. By assessing the results, the composition of brake pads, which can be used in vehicle brakes, was determined. The experimental results were also examined by variance analysis to demonstrate effect factors. Furthermore, when the test results were evaluated in terms of the friction coefficient, wear rate and temperature of the brake disc, a high coefficient of friction, a moderate wear rate and an acceptable temperature of the brake disc were obtained in sample 13. The composition of sample 13, which has the highest friction coefficient, is 3 g brass powder, 9 g cashew, 9 g carbon fibre, 9 g copper dust and 9 g graphite. Lastly, the average friction coefficients of brake pads were estimated through artificial neural network (ANN) analysis. With respect to the results, it was discovered that the generated ANN model promises a high ratio estimation capacity.