Sare Çelik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sare Çelik has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Yılmaz Gür
Department of Mechanical Engineering, Balikesir University, Balikesir, Türkiye
3 shared publications - Ruhan Benlikaya
Composite Researches, Training and Simulation Application and Research Center Balikesir University Balikesir Türkiye
2 shared publications - Ali Oral
Balikesir University, Faculty of Engineering
1 shared publication - Alper Gündoğmuş
Balikesir Universitesi
1 shared publication - Enver Atik
Manisa Celal Bayar Üniversitesi
1 shared publication - Kutay Şirin
Department of Mechanical Engineering Balikesir University Balikesir Türkiye
1 shared publication
Latest Publications
- 20 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (16) , 14431-14443
Enhanced Self‐Healing in Glass Fiber‐Reinforced Epoxy Composites via Vascular Channels: Utilizing Ethyl‐2‐Cyanoacrylate and Interface Optimization
The latent matrix micro‐cracking remains a critical challenge for fiber‐reinforced composites in high‐performance applications. Bio‐inspired self‐healing materials address this by enabling autonomous repair and mechanical restoration. In this study, the vascular channels made from glass tubes filled with ethyl‐2‐cyanoacrylate (ECA) as a healing agent were integrated into glass fiber‐reinforced epoxy composites. To strengthen the weak glass‐resin interface, a stearic acid‐hexane solution was used to coat the glass tubes. Rhodamine B acted as a fluorescent tracer to visualize ECA penetration into the fractured regions of the composites. Neat composite specimens, alongside those containing empty and ECA‐filled vascular channels, were subjected to damage under various impact energies. The self‐healing capabilities of the relevant specimens at room temperature were thoroughly investigated using three‐point bending tests, FTIR, and SEM analyses. These analyses confirmed the morphological and structural distribution of ECA in the specimens and its self‐healing efficiency. Furthermore, the highest healing efficiency (62.68%) was achieved for the specimens with 1.2 vol% ECA subjected to an 18 J impact. Quantitative microscopic analysis of the SEM images revealed that this performance is governed by the formation of optimal crack apertures and controlled vascular fragmentation, which facilitate the effective capillary delivery of the healing agent.
- 20 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (16) , 14431-14443
Enhanced Self‐Healing in Glass Fiber‐Reinforced Epoxy Composites via Vascular Channels: Utilizing Ethyl‐2‐Cyanoacrylate and Interface Optimization
The latent matrix micro‐cracking remains a critical challenge for fiber‐reinforced composites in high‐performance applications. Bio‐inspired self‐healing materials address this by enabling autonomous repair and mechanical restoration. In this study, the vascular channels made from glass tubes filled with ethyl‐2‐cyanoacrylate (ECA) as a healing agent were integrated into glass fiber‐reinforced epoxy composites. To strengthen the weak glass‐resin interface, a stearic acid‐hexane solution was used to coat the glass tubes. Rhodamine B acted as a fluorescent tracer to visualize ECA penetration into the fractured regions of the composites. Neat composite specimens, alongside those containing empty and ECA‐filled vascular channels, were subjected to damage under various impact energies. The self‐healing capabilities of the relevant specimens at room temperature were thoroughly investigated using three‐point bending tests, FTIR, and SEM analyses. These analyses confirmed the morphological and structural distribution of ECA in the specimens and its self‐healing efficiency. Furthermore, the highest healing efficiency (62.68%) was achieved for the specimens with 1.2 vol% ECA subjected to an 18 J impact. Quantitative microscopic analysis of the SEM images revealed that this performance is governed by the formation of optimal crack apertures and controlled vascular fragmentation, which facilitate the effective capillary delivery of the healing agent.
- Open Access
- 17 January 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (1) , 015522
An investigation from raw components to composite: 3D printed Voronoi lattice core structured sandwich composite with woven glass fiber-epoxy outer layer
A key emerging trend in mechanical engineering design involves adopting strategies that build lightweight lattice geometries, particularly for sandwich structures. These structures are characterized by low mass, a significant surface area to volume ratio, high porosity, and suitable mechanical behavior. This study focuses on the fabrication and investigation of thermoplastic polyurethane (TPU) Voronoi lattice core (V-core) structured sandwich composite with woven glass fiber (WGF)-Epoxy outer layer. The TPU V-Core structure was fabricated using the Fused Filament Fabrication (FFF) three dimensional (3D) printing method. Fourier Transform Infrared Spectroscopy (FTIR), Raman Spectroscopy, and Thermogravimetric Fourier Transform Infrared Spectroscopy (TG-FTIR) analyses were used to examine the interactions between the components within the sandwich composite structure. The experimental results demonstrated that the investigated structure has intricate interactions at the interface between the WGF-Epoxy outer layer and the V-core structure. The thermal stability and thermal degradation pathway of the composite and its components were also examined. In addition, three-point bending (TPB) tests were conducted on the sandwich composite and also on the core structures with plain rectangular prism and Voronoi lattice to assess their mechanical behavior.
- 17 January 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (1) , 015522
Open AccessAn investigation from raw components to composite: 3D printed Voronoi lattice core structured sandwich composite with woven glass fiber-epoxy outer layer
A key emerging trend in mechanical engineering design involves adopting strategies that build lightweight lattice geometries, particularly for sandwich structures. These structures are characterized by low mass, a significant surface area to volume ratio, high porosity, and suitable mechanical behavior. This study focuses on the fabrication and investigation of thermoplastic polyurethane (TPU) Voronoi lattice core (V-core) structured sandwich composite with woven glass fiber (WGF)-Epoxy outer layer. The TPU V-Core structure was fabricated using the Fused Filament Fabrication (FFF) three dimensional (3D) printing method. Fourier Transform Infrared Spectroscopy (FTIR), Raman Spectroscopy, and Thermogravimetric Fourier Transform Infrared Spectroscopy (TG-FTIR) analyses were used to examine the interactions between the components within the sandwich composite structure. The experimental results demonstrated that the investigated structure has intricate interactions at the interface between the WGF-Epoxy outer layer and the V-core structure. The thermal stability and thermal degradation pathway of the composite and its components were also examined. In addition, three-point bending (TPB) tests were conducted on the sandwich composite and also on the core structures with plain rectangular prism and Voronoi lattice to assess their mechanical behavior.
- Open Access
- 1 July 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (7) , 075305
Tensile behaviour of continuous carbon fibre reinforced composites fabricated by a modified 3D printer
This study aims to highlight the impact of low-volume (7.5%) continuous carbon fibre reinforcement in three different polymer matrices and the effects of post-processing under hot pressing on the mechanical properties of the structures. A fused deposition modelling (FDM) printer’s print head was modified to directly extrude the polymer matrix and continuous carbon fibre tow together. Both pure and carbon fibre-reinforced samples were cured under hot pressing at 100 °C and 10 kN pressure for 15 min. All samples underwent tensile and hardness tests, and the microstructure of fractured samples was analysed using a scanning electron microscope. The results indicate that continuous carbon fibre reinforcement and hot pressing are crucial for enhancing the mechanical performance of 3D-printed objects.
- 1 July 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (7) , 075305
Open AccessTensile behaviour of continuous carbon fibre reinforced composites fabricated by a modified 3D printer
This study aims to highlight the impact of low-volume (7.5%) continuous carbon fibre reinforcement in three different polymer matrices and the effects of post-processing under hot pressing on the mechanical properties of the structures. A fused deposition modelling (FDM) printer’s print head was modified to directly extrude the polymer matrix and continuous carbon fibre tow together. Both pure and carbon fibre-reinforced samples were cured under hot pressing at 100 °C and 10 kN pressure for 15 min. All samples underwent tensile and hardness tests, and the microstructure of fractured samples was analysed using a scanning electron microscope. The results indicate that continuous carbon fibre reinforcement and hot pressing are crucial for enhancing the mechanical performance of 3D-printed objects.
- 16 January 2023
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 25 (1) , 1-12
The effect of processing parameters on the wear properties Al6061/GNP composites produced by hot pressing
In the present study, the effect of graphene nanoplatelet (GNP) reinforcement in Aluminum material at different rates was investigated on tribological properties. In this scope, the samples were produced by the hot press under determining different production parameters. The wear characteristics of the composites were determined using the ball-on disc wear test method. Ball on disc wear test showed that the Al6061/GNPs composite which was produced with the addition of 1 wt% GNPs, a sintering temperature of 600 °C, and a sintering time of 45 min, had the best wear resistance. Thanks to the GNPs reinforcement, a 61 % reduction in wear rate was achieved when compared to the non-reinforced Al material. The effects of the production parameters on the friction coefficient were investigated using the Taguchi method and it was determined that the most important parameter affecting the friction coefficients of the composites was the wt % GNPs addition. The results showed that the addition of GNPs is an important reinforcing material that reduces the wear rate when added to the structure at certain rates.
- 16 January 2023
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 25 (1) , 1-12
The effect of processing parameters on the wear properties Al6061/GNP composites produced by hot pressing
In the present study, the effect of graphene nanoplatelet (GNP) reinforcement in Aluminum material at different rates was investigated on tribological properties. In this scope, the samples were produced by the hot press under determining different production parameters. The wear characteristics of the composites were determined using the ball-on disc wear test method. Ball on disc wear test showed that the Al6061/GNPs composite which was produced with the addition of 1 wt% GNPs, a sintering temperature of 600 °C, and a sintering time of 45 min, had the best wear resistance. Thanks to the GNPs reinforcement, a 61 % reduction in wear rate was achieved when compared to the non-reinforced Al material. The effects of the production parameters on the friction coefficient were investigated using the Taguchi method and it was determined that the most important parameter affecting the friction coefficients of the composites was the wt % GNPs addition. The results showed that the addition of GNPs is an important reinforcing material that reduces the wear rate when added to the structure at certain rates.
- 4 July 2021
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 23 (2) , 402-413
AZ31B-H24 magnezyum alaşımının sürtünme karıştırma yöntemiyle kaynak edilebilirliğinin incelenmesi
Magnezyum ve alaşımları, hafifliği ve yüksek spesifik mukavemeti nedeni ile endüstride kullanımı oldukça yaygın olan metal olup otomotiv ve uzay-uçak sanayilerindeki mühendislik uygulamalarında ön plana çıkmıştır. Magnezyum alaşımının yanıcı ve düşük ergime sıcaklığına sahip olması bu alaşımların ergitme yöntemleriyle kaynaklı birleştirilmesinde sorunlar oluşturmaktadır. Sürtünme karıştırma kaynağı, düşük işlem sıcaklığı, iyi mekanik özellikler sağlaması gibi avantajları nedeni ile magnezyum alaşımlarına uygulanabilir bir birleştirme metodudur. Çalışmada, AZ31B-H24 magnezyum alaşım levhalarının sürtünme karıştırma kaynak yöntemi ile kaynak edilebilirliği incelenmiştir. Çalışmada, sürtünme karıştırma kaynak parametreleri olarak 1000, 1400 dev/dak dönme hızları; 16, 25, 40, 50 mm/dak ilerleme hızları ve 15, 20 mm omuz çapları seçilerek bu parametrelerde kaynaklama işlemi yapılmıştır. Sürtünme karıştırma kaynağı uygulanan parçaların mekanik özellik tespiti için çekme ve mikro sertlik ölçme testleri uygulanmış, mikro yapı incelemeleri için kaynaklı yapının optik görüntüleri incelenmiş ve XRD analizleri yapılmıştır. Çekme deneyi sonucunda, kaynaklı bağlantıların mukavemeti ana malzemeye göre %75,88’lik bir kaynak dayanım değeri sağlamıştır.
- 4 July 2021
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 23 (2) , 402-413
AZ31B-H24 magnezyum alaşımının sürtünme karıştırma yöntemiyle kaynak edilebilirliğinin incelenmesi
Magnezyum ve alaşımları, hafifliği ve yüksek spesifik mukavemeti nedeni ile endüstride kullanımı oldukça yaygın olan metal olup otomotiv ve uzay-uçak sanayilerindeki mühendislik uygulamalarında ön plana çıkmıştır. Magnezyum alaşımının yanıcı ve düşük ergime sıcaklığına sahip olması bu alaşımların ergitme yöntemleriyle kaynaklı birleştirilmesinde sorunlar oluşturmaktadır. Sürtünme karıştırma kaynağı, düşük işlem sıcaklığı, iyi mekanik özellikler sağlaması gibi avantajları nedeni ile magnezyum alaşımlarına uygulanabilir bir birleştirme metodudur. Çalışmada, AZ31B-H24 magnezyum alaşım levhalarının sürtünme karıştırma kaynak yöntemi ile kaynak edilebilirliği incelenmiştir. Çalışmada, sürtünme karıştırma kaynak parametreleri olarak 1000, 1400 dev/dak dönme hızları; 16, 25, 40, 50 mm/dak ilerleme hızları ve 15, 20 mm omuz çapları seçilerek bu parametrelerde kaynaklama işlemi yapılmıştır. Sürtünme karıştırma kaynağı uygulanan parçaların mekanik özellik tespiti için çekme ve mikro sertlik ölçme testleri uygulanmış, mikro yapı incelemeleri için kaynaklı yapının optik görüntüleri incelenmiş ve XRD analizleri yapılmıştır. Çekme deneyi sonucunda, kaynaklı bağlantıların mukavemeti ana malzemeye göre %75,88’lik bir kaynak dayanım değeri sağlamıştır.
- 29 January 2021
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 23 (1) , 200-209
3 boyutlu yazıcı ile üretilen ABS ve karbon fiber takviyeli ABS kompozitlerde üretim parametrelerinin mekanik özelliklere etkisi
Son yıllarda 3 boyutlu yazıcı teknolojisi ile parça üretimi hızla yaygınlaşmıştır. Geleneksel üretim yöntemlerine göre son derece karmaşık yapıya sahip parçalar çok kısa sürede, düşük maliyetle, hemen hemen hiçbir atık olmadan kolayca üretilebilmektedir. En yaygın olarak kullanılan 3 boyutlu yazıcı yöntemi ise ergiterek biriktirme yöntemidir (EBY). Ancak bu yöntemle sadece akrolonitril-butadien stiren (ABS) veya polilaktik asit (PLA) gibi termoplastikler kullanılarak üretim yapılabilmektedir. Son yıllarda, istenilen malzeme özelliklerinin elde edilmesi için takviyeli termoplastikler kullanılarak, EBY teknolojisi ile çalışan 3 üç boyutlu yazıcılar ile üretim yapılmaya başlanmıştır. Bu çalışmada ABS ve kırpılmış karbon elyafı takviyeli ticari ABS kompozit filamentler kullanılarak EBY teknolojili 3 boyutlu yazıcı ile üretilen ve farklı yazdırma yönleri ve farklı içyapı doldurma açılarına sahip çekme testi numunelerinin çekme testi sonuçları karşılaştırılmıştır. Çekme testi numuneleri ISO 527-2 Type-1A standardı referans alınarak 3 boyutlu yazıcıda yazdırılmıştır. Test numunelerinin içyapılarının 3 boyutlu yazıcı ile yazdırılması esnasında baskı kafasının izlediği yolun x ekseni ile yaptığı açılar 0o/90o ile +45o/−45o arasında değiştirilerek farklı içyapı doldurma açılarının mekanik özellikler üzerinde etkisi araştırılmıştır. Ayrıca mekanik özelliklerin test parçasının üretim platformu üzerine yerleştirme biçiminin etkisini tespit etmek amacıyla da test numuneleri platform üzerine yatay ve yan kenar şeklinde yerleştirilerek yazdırılmıştır. Normal ABS, aynı doldurma açısına ve aynı yönde üretilen karbon fiber takviyeli ABS'den daha iyi mekanik özelliklere sahip olduğu görülmüştür.
- 29 January 2021
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 23 (1) , 200-209
3 boyutlu yazıcı ile üretilen ABS ve karbon fiber takviyeli ABS kompozitlerde üretim parametrelerinin mekanik özelliklere etkisi
Son yıllarda 3 boyutlu yazıcı teknolojisi ile parça üretimi hızla yaygınlaşmıştır. Geleneksel üretim yöntemlerine göre son derece karmaşık yapıya sahip parçalar çok kısa sürede, düşük maliyetle, hemen hemen hiçbir atık olmadan kolayca üretilebilmektedir. En yaygın olarak kullanılan 3 boyutlu yazıcı yöntemi ise ergiterek biriktirme yöntemidir (EBY). Ancak bu yöntemle sadece akrolonitril-butadien stiren (ABS) veya polilaktik asit (PLA) gibi termoplastikler kullanılarak üretim yapılabilmektedir. Son yıllarda, istenilen malzeme özelliklerinin elde edilmesi için takviyeli termoplastikler kullanılarak, EBY teknolojisi ile çalışan 3 üç boyutlu yazıcılar ile üretim yapılmaya başlanmıştır. Bu çalışmada ABS ve kırpılmış karbon elyafı takviyeli ticari ABS kompozit filamentler kullanılarak EBY teknolojili 3 boyutlu yazıcı ile üretilen ve farklı yazdırma yönleri ve farklı içyapı doldurma açılarına sahip çekme testi numunelerinin çekme testi sonuçları karşılaştırılmıştır. Çekme testi numuneleri ISO 527-2 Type-1A standardı referans alınarak 3 boyutlu yazıcıda yazdırılmıştır. Test numunelerinin içyapılarının 3 boyutlu yazıcı ile yazdırılması esnasında baskı kafasının izlediği yolun x ekseni ile yaptığı açılar 0o/90o ile +45o/−45o arasında değiştirilerek farklı içyapı doldurma açılarının mekanik özellikler üzerinde etkisi araştırılmıştır. Ayrıca mekanik özelliklerin test parçasının üretim platformu üzerine yerleştirme biçiminin etkisini tespit etmek amacıyla da test numuneleri platform üzerine yatay ve yan kenar şeklinde yerleştirilerek yazdırılmıştır. Normal ABS, aynı doldurma açısına ve aynı yönde üretilen karbon fiber takviyeli ABS'den daha iyi mekanik özelliklere sahip olduğu görülmüştür.