EAEnver Atik

Enver Atik

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Enver Atik has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigation Of Induction Sinterability Of Powder Metal Parts Of Different Shapes And Sizes

    by Can Çivi, Enver Atik

    Powder metal parts are used in many applications because of widely advantages. Induction sintering is a rapid sintering method, and it is moving towards to an important alternative process of conventional sintering by means of time and energy saving and more improved mechanical properties. In this study, five different samples were pressed with dual axis press under 600-800 MPa pressure. The samples were sintered with conventionally and with medium frequency (30 kHz) induction sintering mechanism. The body of the samples was heated directly by induction sintering. Comparison of the mechanical properties and microstructures of samples which produced by conventional and induction sintering methods were carried out. As a result of study, it was observed that induction sintering is more effective process in order to obtain acceptable mechanical properties than conventional sintering. Also, similar microstructural characteristics were obtained in shorter treatment times by induction sintering.


  • Open Access

    Mechanical effects of sodium pentaborate pentahydrate and sodium pentaborate anhydrate additives in polypropylene

    by Burhan Şahin, Enver Atik

    This research examines the effect of micro size sodium pentaborate pentahydrate and anhydrate forms on the physicochemical and mechanical properties of filled polypropylene (isotactic homopolimer – Borealis HE125MO) composite matrices. The Sodium pentaborate pentahydrate and anhydrite dried 105°C 1 hour and mixed with micro compounder with polypropylene (with different proportions) and produced test samples with injection molding method. Mechanical properties were measured (tensile strength, modulus of elasticity, ultimate strength, tensile at yield (at room temperature)) along with hardness (charpy impact) test. Increasing filler content lead to an increase mechanical strength of the composite material depends on the percentage quantity of mixture proportion. The observed increase in tensile strength is %4,2 with %1 sodium pentaborate pentahydrate additive. The modulus of elasticity increases with additive quantity and the ultimate strength and strain at yield effected parallel with tensile strength change. With high proportion (%5-%10) of filler content, the mechanical properties decreased but increased the hardness. To understand the physicochemical effects, FTIR test applied on samples and O-H bonds effects and C-C bonds change observed. According to Infrared spectroscopy, the polypropylene had changed 1,56% with sodium pentaborate pentahydrate additive and 2,86% with %1,5 additive of sodium pentaborate anhydrite form. The fingerprint region alterations at FTIR tests and water effect observed. The molecular bonding effects of sodium pentaborate with chain of isotactic homopolimer examined. The nucleating effect of sodium pentaborate in polypropylene is viewed with SEM test. In microstructure, positioning effects of sodium pentaborate particles in chain/fiber structure of polypropylene observed and associated with mechanical properties and physicochemical impacts.


  • The effect of processing parameters on the wear properties Al6061/GNP composites produced by hot pressing

    by Türker Türkoğlu, Sare Çeli̇k, Nail Aslan, Enver Ati̇k

    In the present study, the effect of graphene nanoplatelet (GNP) reinforcement in Aluminum material at different rates was investigated on tribological properties. In this scope, the samples were produced by the hot press under determining different production parameters. The wear characteristics of the composites were determined using the ball-on disc wear test method. Ball on disc wear test showed that the Al6061/GNPs composite which was produced with the addition of 1 wt% GNPs, a sintering temperature of 600 °C, and a sintering time of 45 min, had the best wear resistance. Thanks to the GNPs reinforcement, a 61 % reduction in wear rate was achieved when compared to the non-reinforced Al material. The effects of the production parameters on the friction coefficient were investigated using the Taguchi method and it was determined that the most important parameter affecting the friction coefficients of the composites was the wt % GNPs addition. The results showed that the addition of GNPs is an important reinforcing material that reduces the wear rate when added to the structure at certain rates.


  • Open Access

    Analytical investigation of a new approach to calculation for effective length of the rolling element used in closed end needle roller bearings of driveshaft

    by Onur Şen, Enver Ati̇k

    The presence of the oscillating motion in a mechanical system, is vital in terms of the service life. Because the machine elements are under effect of fatigue due to the oscillating motion. The service life of the bearings which are in the forefront among the machine elements subjected to oscillating motion, can be calculated via an equation that depends on several variables, one of which is basic dynamic load rating (C). In this context, basic dynamic load rating (C) is one of the most important factors on estimating the service life. One of where bearing applications used in, is universal joint of driveshaft. A bearing on a universal joint consists of needle roller elements having larger contact area compared to the ball elements. Universal joint bearing is mounted in a bore on a component called yoke part, and so yoke part supports the bearing. In the calculation of basic dynamic load rating for universal joint bearing, effective length of the rolling element is the key factor. In this paper, a new approach to determine the effective length of rolling element used in closed end needle roller bearings of driveshaft has been investigated analytically and the effect of the said approach on the basic dynamic load rating and bearing life has been revealed in terms of ISO 281.