İTİhsan Toktaş

İhsan Toktaş

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


İhsan Toktaş has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Özgün Bir Latis Yapı Tasarımının Auxetic Davranışının İncelenmesi

    by Nuriye Nur Kaya, İhsan Toktaş

    Auxetic yapılar, yapıyı oluşturan geometrik şekillerinden dolayı negatif poison oranına sahip özel yapılardır. Bu yapılara çekme kuvveti uygulandığında enine ve boyuna genişlemeler izlenirken, basma kuvveti uygulandığında ise enine ve boyuna daralmalar gözlenmektedir. Auxetic yapılarda kiral, ok ucu, re-entrant gibi birçok farklı birim hücre tasarımları mevcuttur. Bu çalışmada da Stravaski adı verilen özgün bir hücre tasarımının auxeticlik özelliği araştırılmıştır. Farklı geometrik iç kalınlık ölçüleri verilerek tasarlanan latis yapının sonlu elemanlar analizleri gerçekleştirilmiş ve negatif poison oranına sahip olduğu bulunmuştur. 224*224 mm, 160*160 mm ve 120*120 mm’lik ölçüde tasarlanan Stravaski latis hücre yapılarının 1 mm geometrik iç kalınlıklarında en iyi auxetic özellik tespit edilmiştir. Ayrıca kendi içlerindede en küçük ölçüye sahip olan 120*120 mm’lik Stravaski latis yapısının diğer çalışılan yapılara göre en yüksek auxetic özellik gösterdiği bulunmuştur.

  • Open Access

    Eliptik Delikli İnce Cidarlı Küresel Bir Elemanın Basınç Altında Gerilme Yığılma Faktörünün Sonlu Elemanlar Analizi Ve Yapay Sinir Ağları İle Modellenmesi

    by İhsan Toktaş

    Bu çalışmada; eliptik delikli ince cidarlı küresel bir elemanın basınç altındaki davranışları Sonlu Elemanlar Analiz (SEA) yöntemi ile parametrik olarak analiz edilmiş ve Yapay Sinir Ağları (YSA) ile modellenmiştir. Modelleme esnasında, küresel elemanın yarıçapı 500 mm. olarak alınmış ve değişken parametrelere göre küresel elemana cidar kalınlığı verilmiştir. Küresel elemanın içinden boydan boya geçen yarıçapları a ve b olan eliptik bir delik tanımlanmıştır. Küresel elemanın iç yüzeyine sabit basınç gerilmesi uygulanmış ve elemanda oluşan gerilmeler ve gerilme yığılma faktörleri optimize edilmiştir. Parametrik modelden elde edilen sonuçlar bir YSA modelinde öğretilerek farklı boyut ve basınç değerleri için eliptik delikli ince cidarlı küresel bir elemanın gerilme, gerinim, deformasyon, gerilme yığılma faktörleri ve farklı teoremlere göre emniyet katsayıları belirlenmiştir.


  • Open Access

    Mobilya Endüstrisinde Tasarımların Sınai Haklarının Korunması Üzerine Vaka İncelemeleri

    by Taner Aşçı, İhsan Toktaş

    Mobilya, yaşam alanlarımızın temel unsurları arasında yer almaktadır. Yaşamsal ihtiyaçlarımızın karşılanmasında ya da kolaylaştırılmasında her yaşam alanında mobilyalara ihtiyaç duyulmaktadır. Şehir meydanlarından ofislere, otobüs duraklarından konutlara kadar insanın var olduğu her alanda mobilya ihtiyacı da var olmaktadır. Uzun ve zahmetli tasarım ve imalat süreçleri ile meydana gelen mobilyalarda sınai hakların tesis edilmesi mobilya sektörünü daha rekabetçi hale getirebilir. Dünya mobilya ihracatçıları istatistiklerine göre Türkiye 11nci sırada yer almaktadır. Bu durum sektörde gelişmeye açık yanların bulunduğunu işaret etmektedir. Özellikle özgün ürün geliştirmek ve ürünlerin haklarını koruma altına almak, iç ve dış piyasada işletmelere önemli kazanımlar sağlamaktadır. Çalışmada, ülkemizde mobilya endüstrisinde görülen ihtilafların çözümünde başvurulan mevzuat ve yasal yollar ile vaka incelemesi çalışmaları da yer bulmaktadır. Sınai hakların korunmasında etkili şekilde kullanılan patent - faydalı model ya da tasarım tescilleri işletmeye sınai aidiyet noktasında resmi kanıt niteliği oluşturmaktadır. Diğer yandan uluslararası ticarette hedef ülkenin meri mevzuatı dikkate alınacağından sınai hakların diğer ülkelerde de koruma altına alınmasının gerekli olduğu göz ardı edilmemelidir. Bu noktada meslek örgütleri ile birlikte sivil toplum kuruluşu ve üniversitelerin iş birliği önem taşımaktadır.

  • Open Access

    INVESTIGATION OF THE AUXETIC BEHAVIOR OF AN ORIGINAL LATTICE STRUCTURE DESIGN

    by Nuriye Nur Kaya, Cengiz Eldem, İhsan Toktas

    Auxetic structures are special structures with negative Poisson's ratio due to their geometric shapes in their internal structure. When tensile force is applied to these structures, transverse and longitudinal expansions are observed, while transverse and longitudinal contractions are observed when compressive force is applied. There are many different unit cell designs such as chiral, arrowhead, re-entrant in auxetic structures. In this study, a unique cell design was studied and the behavior of an auxetic lattice structure was investigated. The lattice structure designed with different geometric thicknesses and different matrices was analyzed with the finite element analysis program and found to have a negative Poisson's ratio. In the designed lattice structure, the structure with 4×4 matrix and 3 mm geometric thickness was found to have the best negative Poisson's ratio.


  • Open Access

    Investigation of the Auxetic of a novel geometric structure and improvement of Poisson’s ratio at different inner thicknesses

    by İsmail Erdoğan, İhsan Toktas

    Poisson’s ratio, one of the important mechanical properties of materials and structures, is positive for almost all of the known materials and structures. However, auxetic materials or structures has negative Poisson’s ratios. Characteristics of the auxetic structures are very important to be used in design of a new structure. Computational or experimental studies on auxetic structures have been increasing in literature. In this study, a new auxetic lattice structure with different Poisson’s ratios was designed and studied by finite element analysis. Mechanical properties of the newly designed auxetic lattice structures were analyzed with different lattice inner thickness. Results showed that change in inner thickness affects the Poisson’s ratio, mass, volume and surface area of the newly designed Auxetic lattice structures.


  • Open Access

    Modeling of Stress Concentration Factor Using Artificial Neural Networks for a Flat Tension Bar with Opposite V-Shaped Notches

    by Mehmet Eren, İhSan Toktaş, Murat Tolga Özkan

    Machine parts are exposed to stress accumulation due to geometric differences. Determining the stress accumulation locations is crucial to the design procedures. Studies on stress concentrations have been conducted in the past using a variety of theoretical and experimental methodologies, and distinct interpretations have been offered depending on the geometry of the machine part to be produced. The ability to complete activities with the least amount of effort and in the shortest amount of time has emerged as a result of the new computer technologies and software that have impacted many aspects of our everyday lives. One of these methods is the artificial neural networks (ANN) model, which is a branch of artificial intelligence. It is argued as a thesis in this study that fast and low-cost solutions can be found to problems in the field of solid mechanics by using the ANN model. For this purpose, a model has been developed to determine the SCF value with the ANN model of a plate with symmetrical V-shaped notch. The graphs obtained from previous experimental studies were converted to digital format and the Kt values obtained for the V-shaped notch problem with different parameters were converted into a data file. In this file, the SCF values to be obtained according to the strength upper limit safety factor value of the machine part, depending on the dimensional dimensions and material type required for the design, are calculated numerically in the form of an Excel file. An ANN-based code was created in MATLAB software and a new solution method was presented for parts containing a V-shaped notch.


  • Investigation of The Effect of Geometry Inner Thickness on New Designed Auxetic Structure

    by İsMail Erdoğan, İhSan Toktas

    Poisson’s ratio is important mechanical property of materials and structure. Material and Structure showing negative Poisson’s ratios are called Auxetic. Properties of the Auxetic structures are very important to design the new structure, especially mechanical properties of the Auxetic materials that have structurally and functionally mission. Many researchers made experimental and theoretical works apropos this matter. In this study, the newly designed Auxetic lattice structure Poisson’s ratio was checked over via exploiting finite element analysis. 14 different lattice structures with respect to inner lattice thickness configurations are investigated. All examined structures have a negative Poisson’s ratio. Inner lattice thickness is increased; negative Poisson’s ratio values are decreased (closes to -1.) in these examined lattice structures. 4x2 lattice orientation has lowest Poisson’s ratio than 4x4 Lattice structure Poisson’s ratio, 4x2 is more Auxetic. 4.9 mm inner lattice thickness and 4x2 lattice matrix examined example has lowest Poisson’s ratio that is -0,55. Beneficial to indicate the purview of the structure on the applied force, the stiffness values and the stiffness/mass values were examined. Their energy dissipation capabilities were analyzed.


  • Estimations of Stress Concentration Factors (Cw/Kts) For Helical Circular/Square Cross Sectional Tension-Compression Springs And Artificial Neural Network Modelling

    by M. Tolga Özkan, İhsan Toktaş, Kaan Doğanay

    Springs are used for various purposes in machine design as they can store energy under load, due to their elastic deformation characteristics. There are many types and profiles of springs. For a round wire helical compression or tension spring of small pitch angle, the Wahl factor, a correction factor (Cw) taking into account curvature and direct shear stress, is generally used in the design. The corresponding stress concentration factors, which may be useful for mechanics of materials problems, are obtained by taking the nominal shear stress τnom as the sum of the torsional stress (τ) and the direct shear stress (τ) for round wire. In the case of the wire of square cross-section, τnom is the sum of the torsional stress and the direct shear stress. For design calculations it is recommended that the simpler Wahl factor be used. The same value of max will be obtained whether one uses Cw or Kts. This study contains the determination of stress concentration factor and Wahl factor. For this aim, stress concentration factor charts were converted numerical values for round and square wires. These values were collected in an excel file. ANN (Artificial Neural Networks) model was developed using the data. It is an easy and convenient method, ANN model, was presented for the determination of stress concentration and Wahl factor for spring design.


  • Determination of Stress Concentration Factor (Kt) for a Crankshaft Under Bending Loading: An Artificial Neural Networks Approach

    by İhSan Toktaş, M. Tolga Özkan, Fulya Erdemi̇r, Nurullah Yuksel

    Crankshafts are used in especially engines. Crankshafts are usually effected bending and torsional stress. These loading situations are important for design of engine and its parts. Crankshaft design requires design experience and engineering calculations. When the engineering calculation is performed, stress concentration factor is put into effect. These factors are usually obtained from Stress concentration factor Charts. Reading the real stress concentration factor from charts can be resulted in getting from false values. This study is an update work of old studies. Using the new computer techniques stress concentration factor values were converted into numerical values. Stress concentration factor values were collected in a database. Artificial Neural Network (ANN) Model was improved using the database. ANN model is gave to us time economy and high accuracy of obtaining the stress concentration values.