Hayrettin Düzcükoğlu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hayrettin Düzcükoğlu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Mürsel Ekrem
Necmettin Erbakan University
2 shared publications - Rifat Yakut
Department of Energy Systems Engineering, Faculty of Technology, Batman University, Batman 72000, Türkiye
2 shared publications - Abdullah Aslan
Selcuk University
1 shared publication - Ahmet Avcı
Mechanical Engineering Department, Engineering Faculty, Selcuk University, Konya 42030, Turkey
1 shared publication - Aydın Güneş
Department of Mechanical Engineering, Abdullah Gul University, Kayseri 38080, Turkey
1 shared publication - Babür Özçelik
Gebze Technical University, Department of Mechanical Engineering, Kocaeli, Türkiye
1 shared publication
Latest Publications
- Open Access
- 29 June 2026
- Published by SAGE Publications in International Journal of Damage Mechanics
MXene-reinforced Elium ® composites: A comprehensive study on tensile and flexural strengths, fracture toughness, thermal properties and damage mechanisms
This study reports the synthesis of multilayer Ti 3 C 2 T x MXene through selective etching of Ti 3 AlC 2 and its incorporation into Elium ® thermoplastic resin at loadings of 0.25–1.0 wt.%. The resulting nanocomposites were characterized by scanning electron microscopy (SEM), X-ray diffraction, thermogravimetric analysis/differential scanning calorimetry, and mechanical tests, including tensile (ASTM D638), flexural (ASTM D790), and fracture toughness (ASTM D5045) analyses. The 0.75 wt.% MXene composite exhibited the most balanced performance, achieving a tensile strength of 69.45 MPa, a flexural strength of 110 MPa, and a 31% improvement in fracture toughness over neat Elium ® . These enhancements were attributed to uniform nanofiller dispersion and effective interfacial interaction that facilitates stress transfer and crack deflection. SEM fractography revealed a transition from smooth, brittle fracture surfaces in the neat matrix to rough, branched crack paths in the MXene-filled composites, indicating improved energy dissipation. Overall, MXene/Elium ® nanocomposites showed superior strength, toughness, and thermal stability, highlighting their potential as lightweight and recyclable materials for structural applications in automotive, aerospace, and protective sectors.
- 29 June 2026
- Published by SAGE Publications in International Journal of Damage Mechanics
Open AccessMXene-reinforced Elium ® composites: A comprehensive study on tensile and flexural strengths, fracture toughness, thermal properties and damage mechanisms
This study reports the synthesis of multilayer Ti 3 C 2 T x MXene through selective etching of Ti 3 AlC 2 and its incorporation into Elium ® thermoplastic resin at loadings of 0.25–1.0 wt.%. The resulting nanocomposites were characterized by scanning electron microscopy (SEM), X-ray diffraction, thermogravimetric analysis/differential scanning calorimetry, and mechanical tests, including tensile (ASTM D638), flexural (ASTM D790), and fracture toughness (ASTM D5045) analyses. The 0.75 wt.% MXene composite exhibited the most balanced performance, achieving a tensile strength of 69.45 MPa, a flexural strength of 110 MPa, and a 31% improvement in fracture toughness over neat Elium ® . These enhancements were attributed to uniform nanofiller dispersion and effective interfacial interaction that facilitates stress transfer and crack deflection. SEM fractography revealed a transition from smooth, brittle fracture surfaces in the neat matrix to rough, branched crack paths in the MXene-filled composites, indicating improved energy dissipation. Overall, MXene/Elium ® nanocomposites showed superior strength, toughness, and thermal stability, highlighting their potential as lightweight and recyclable materials for structural applications in automotive, aerospace, and protective sectors.
- Open Access
- 1 November 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (11) , 115003
Investigation of nano-copper added cutting fluid performance on milling process by using the Bees Algorithm and experimental design methods
In this study, the tribological performance of copper nanoparticles coated with different ligands added to the metal cutting fluid as an additive was investigated. Copper, which has a high heat transfer coefficient and self-lubricating properties, is aimed at reducing the temperature in the chip area and reducing wear by acting as a lubricant, increasing tool life and surface quality of the processed material. The study was carried out in four stages. In the first stage, UV absorbance, STEM, wettability, and PSA analyses were performed on gelatine, cellulose, and PVP-coated copper nanoparticles synthesised by the chemical reduction method. According to the results of the analysis, the best ligand was gelatine. In the second stage, a pin-on-disc wear test was performed under different speeds (0.5, 0.7, and 0.9 m s −1 ), loads (10, 20, and 35 N), and ligand parameters. According to the friction coefficient, weight loss, and 3d topography images obtained from the wear experiments, the ligands that showed the best performance were gelatine, PVP, and cellulose, respectively. In the third stage, the chip removal process was carried out using the response surface method at different speeds, feeds, depths, and nano-fluid environments. In the 3d topography analyses, the best result in terms of surface roughness was obtained in the boron solution, and the best result in cutting forces was obtained in the gelatine-coated copper nanoparticle (CuNP-Gel) environment. In the tool wear experiment, boron solution and CuNP-Gel were used as coolant/lubricant liquids, and it was observed that the tool wear occurs more slowly in the CuNP-Gel environment.
- 1 November 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (11) , 115003
Open AccessInvestigation of nano-copper added cutting fluid performance on milling process by using the Bees Algorithm and experimental design methods
In this study, the tribological performance of copper nanoparticles coated with different ligands added to the metal cutting fluid as an additive was investigated. Copper, which has a high heat transfer coefficient and self-lubricating properties, is aimed at reducing the temperature in the chip area and reducing wear by acting as a lubricant, increasing tool life and surface quality of the processed material. The study was carried out in four stages. In the first stage, UV absorbance, STEM, wettability, and PSA analyses were performed on gelatine, cellulose, and PVP-coated copper nanoparticles synthesised by the chemical reduction method. According to the results of the analysis, the best ligand was gelatine. In the second stage, a pin-on-disc wear test was performed under different speeds (0.5, 0.7, and 0.9 m s −1 ), loads (10, 20, and 35 N), and ligand parameters. According to the friction coefficient, weight loss, and 3d topography images obtained from the wear experiments, the ligands that showed the best performance were gelatine, PVP, and cellulose, respectively. In the third stage, the chip removal process was carried out using the response surface method at different speeds, feeds, depths, and nano-fluid environments. In the 3d topography analyses, the best result in terms of surface roughness was obtained in the boron solution, and the best result in cutting forces was obtained in the gelatine-coated copper nanoparticle (CuNP-Gel) environment. In the tool wear experiment, boron solution and CuNP-Gel were used as coolant/lubricant liquids, and it was observed that the tool wear occurs more slowly in the CuNP-Gel environment.
- 11 April 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (1) , 309-317
Investigation of the Durability and Performance of Gears Made of Glass Fiber, Carbon and Bronze-Reinforced Polytetrafluoroethylene Matrix Composite Material
Polymer gears are often used in power transmission due to their numerous advantages. Heat accumulates on polymer gears during operation. Over time, this accumulated heat leads to damage; and shortens the service life of the gears. To prevent this, various fillers are added to the polymer materials. These fillers help to dissipate the heat generated on the gears. In this study, 25% glass fibers, 35% carbon powder, and 60% bronze particles were added to the polytetrafluoroethylene (PTFE) matrix to determine the wear behavior of gears. The properties of the matrix and the filler mainly influence the wear behavior of PTFE composites. The study showed that all composite gears with filler have better wear resistance than pure PTFE gears due to their better thermal stability. After the tests, it was found that the gears made of PTFE + 35% carbon additive had about 12 times better wear rates than those made of pure PTFE. Based on the average temperature values of the experiment, it was found that the mass temperature of gears made of 35% carbon-doped PTFE is about 38-39% lower than that of pure PTFE. This study contributes to the standard studies on heat build-up, thermal damage, and wear of gears made of polymers with different fillers and ratios.
- 11 April 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (1) , 309-317
Investigation of the Durability and Performance of Gears Made of Glass Fiber, Carbon and Bronze-Reinforced Polytetrafluoroethylene Matrix Composite Material
Polymer gears are often used in power transmission due to their numerous advantages. Heat accumulates on polymer gears during operation. Over time, this accumulated heat leads to damage; and shortens the service life of the gears. To prevent this, various fillers are added to the polymer materials. These fillers help to dissipate the heat generated on the gears. In this study, 25% glass fibers, 35% carbon powder, and 60% bronze particles were added to the polytetrafluoroethylene (PTFE) matrix to determine the wear behavior of gears. The properties of the matrix and the filler mainly influence the wear behavior of PTFE composites. The study showed that all composite gears with filler have better wear resistance than pure PTFE gears due to their better thermal stability. After the tests, it was found that the gears made of PTFE + 35% carbon additive had about 12 times better wear rates than those made of pure PTFE. Based on the average temperature values of the experiment, it was found that the mass temperature of gears made of 35% carbon-doped PTFE is about 38-39% lower than that of pure PTFE. This study contributes to the standard studies on heat build-up, thermal damage, and wear of gears made of polymers with different fillers and ratios.
- Open Access
- 18 September 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (9) , 407
Investigation of Friction Coefficient Changes in Recycled Composite Materials under Constant Load
The surface quality of machine elements may deteriorate over time while operating under different conditions. This deterioration adversely affects the wear behavior in the contact areas, and these materials become unusable over time. In machine elements especially, the heat transfer, wear amount and surface roughness parameters in the contact area are very important in order for the system to work efficiently. In order to understand this change, composite materials were produced by adding spheroidal graphite cast iron (GGG40) with high lubricating properties at different rates to bronze (CuSn10), which is widely used as a self-lubricating bearing material. In this study, four different mixing ratios (B60D40, B70D30, B80D20 and B90D10) and B100, which is completely produced from bronze chips, were used for comparison purposes. In addition, these produced composite materials were compared with pure CuSn10 and pure GGG40 via double-acting isostatic hot pressing, and then the results were examined. The composite materials were made at two different temperatures (400 °C and 450 °C) and three different pressures (480 MPa, 640 MPa and 820 MPa) using recycled waste chips. Composites produced by recycling waste chips both reduce costs and make a positive contribution to the natural environment. Thus, more advantageous self-lubricating bearing materials will be produced, and the efficiency will be increased in these materials. The time-dependent variation in the friction coefficient observed after the wear tests performed under constant load is explained, and the resulting surface structures are presented with SEM images and EDS analyses. After the wear tests, it was observed that the process parameters used in production effectively influenced the wear behavior. In particular, when the production pressure was low (480 MPa), the wear behavior was adversely affected because sufficient bonding between the chips could not be achieved. In addition, as the amount of GGG40 used as a reinforcement material increased, the spheroidal graphite contained in it positively affected the wear behavior. The lubricating effect provided by this spheroidal graphite reduced wear in the contact area and the friction coefficient.
- 18 September 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (9) , 407
Open AccessInvestigation of Friction Coefficient Changes in Recycled Composite Materials under Constant Load
The surface quality of machine elements may deteriorate over time while operating under different conditions. This deterioration adversely affects the wear behavior in the contact areas, and these materials become unusable over time. In machine elements especially, the heat transfer, wear amount and surface roughness parameters in the contact area are very important in order for the system to work efficiently. In order to understand this change, composite materials were produced by adding spheroidal graphite cast iron (GGG40) with high lubricating properties at different rates to bronze (CuSn10), which is widely used as a self-lubricating bearing material. In this study, four different mixing ratios (B60D40, B70D30, B80D20 and B90D10) and B100, which is completely produced from bronze chips, were used for comparison purposes. In addition, these produced composite materials were compared with pure CuSn10 and pure GGG40 via double-acting isostatic hot pressing, and then the results were examined. The composite materials were made at two different temperatures (400 °C and 450 °C) and three different pressures (480 MPa, 640 MPa and 820 MPa) using recycled waste chips. Composites produced by recycling waste chips both reduce costs and make a positive contribution to the natural environment. Thus, more advantageous self-lubricating bearing materials will be produced, and the efficiency will be increased in these materials. The time-dependent variation in the friction coefficient observed after the wear tests performed under constant load is explained, and the resulting surface structures are presented with SEM images and EDS analyses. After the wear tests, it was observed that the process parameters used in production effectively influenced the wear behavior. In particular, when the production pressure was low (480 MPa), the wear behavior was adversely affected because sufficient bonding between the chips could not be achieved. In addition, as the amount of GGG40 used as a reinforcement material increased, the spheroidal graphite contained in it positively affected the wear behavior. The lubricating effect provided by this spheroidal graphite reduced wear in the contact area and the friction coefficient.
- Open Access
- 30 June 2020
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 4 (2) , 111-115
Design of ALB Tester for Heavy Vehicle Brake Systems
The brake system is used to keep the speed of the moving vehicle con-stant, slow down, stop it and fix it while parked. Heavy vehicles have an air braking system. (71/320/AT) It should be produced in accordance with the regulations of motor vehicle classes and brake systems. Periodic tests should be carried out in authorized institutions. In the brake systems of vehicles in Trucks, Trailers, Trailers, Semi Trailers, Buses, load adjusting valves called ALB are used, which increase or decrease the rear brake forces of the vehicle according to the load of the vehicle. ALB can be used mechanically or pneumatically in heavy vehicles. In this study, a test device was designed us-ing the microcontroller card, pressure sensor and LCD screen in order to ena-ble the operator, who performed the pneumatic ALB test, to perform the test alone without help and to increase the reliability of the test. As a result of the study, the operator was able to perform the Pneumatic ALB test alone, in-crease the reliability, and save time and labor.
- 30 June 2020
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 4 (2) , 111-115
Open AccessDesign of ALB Tester for Heavy Vehicle Brake Systems
The brake system is used to keep the speed of the moving vehicle con-stant, slow down, stop it and fix it while parked. Heavy vehicles have an air braking system. (71/320/AT) It should be produced in accordance with the regulations of motor vehicle classes and brake systems. Periodic tests should be carried out in authorized institutions. In the brake systems of vehicles in Trucks, Trailers, Trailers, Semi Trailers, Buses, load adjusting valves called ALB are used, which increase or decrease the rear brake forces of the vehicle according to the load of the vehicle. ALB can be used mechanically or pneumatically in heavy vehicles. In this study, a test device was designed us-ing the microcontroller card, pressure sensor and LCD screen in order to ena-ble the operator, who performed the pneumatic ALB test, to perform the test alone without help and to increase the reliability of the test. As a result of the study, the operator was able to perform the Pneumatic ALB test alone, in-crease the reliability, and save time and labor.
- 29 September 2017
- Published by ASME International in Journal of Tribology
- Vol. 140 (2)
Friction and Wear Performance of Epoxy Resin Reinforced With Boron Nitride Nanoplatelets
In this study, the effects of addition of boron nitride nanoplatelets (BNNPs) upon friction and wear behavior of epoxy resin have been investigated by using pin-on-disk test. It has been reported in the literature that certain amounts of BNNP addition can be useful for enhancement of mechanical properties. Therefore, it is very important to obtain the effect of such addition upon friction and wear performance of epoxy resin. BNNPs have been incorporated at 0.3–0.5–0.7–1 wt %. It is shown that BNNP addition results in decrease in friction coefficient and wear. It is also shown that the best results are obtained with 0.5% nanoplatelet addition. It is also observed that heat conduction of epoxy resin is enhanced by the nanoplatelet addition.
- 29 September 2017
- Published by ASME International in Journal of Tribology
- Vol. 140 (2)
Friction and Wear Performance of Epoxy Resin Reinforced With Boron Nitride Nanoplatelets
In this study, the effects of addition of boron nitride nanoplatelets (BNNPs) upon friction and wear behavior of epoxy resin have been investigated by using pin-on-disk test. It has been reported in the literature that certain amounts of BNNP addition can be useful for enhancement of mechanical properties. Therefore, it is very important to obtain the effect of such addition upon friction and wear performance of epoxy resin. BNNPs have been incorporated at 0.3–0.5–0.7–1 wt %. It is shown that BNNP addition results in decrease in friction coefficient and wear. It is also shown that the best results are obtained with 0.5% nanoplatelet addition. It is also observed that heat conduction of epoxy resin is enhanced by the nanoplatelet addition.
- 1 January 2015
- Published by EJournal Publishing in International Journal of Materials, Mechanics and Manufacturing
- Vol. 3 (2) , 117-120
Effect of Boron Addition on Mechanical Properties of 60SiCr7 Stell
- 1 January 2015
- Published by EJournal Publishing in International Journal of Materials, Mechanics and Manufacturing
- Vol. 3 (2) , 117-120
Effect of Boron Addition on Mechanical Properties of 60SiCr7 Stell
- 8 October 2010
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 10 (6) , 545-555
The Use of Cooling Holes to Decrease the Amount of Thermal Damage on a Plastic Gear Tooth
- 8 October 2010
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 10 (6) , 545-555
The Use of Cooling Holes to Decrease the Amount of Thermal Damage on a Plastic Gear Tooth