RYRifat Yakut

Rifat Yakut

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Rifat Yakut has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Nb Reinforcement on the Wear Behavior of Spheroidal Graphite Cast Iron

    by Rifat Yakut

    Spheroidal graphite cast iron, which is commonly used in a variety of applications, is subject to sliding wear and tear during operation. This damage can be prevented by increasing its strength value. In this study, 0%, 0.191%, and 0.304% niobium-reinforced spheroidal graphite cast irons were produced. Specimens for hardness, compression, and abrasion tests were produced in accordance with the standards for the tests of the sand mold cast specimens. In order to compare the results of the tests, test specimens reinforced with 0.191% and 0.304% niobium, as well as 0% (unreinforced), were also produced. The hardness and compression strength of the niobium-reinforced and unreinforced specimens were tested in accordance with the standards. In addition, wear tests were carried out at 5 N, 10 N, and 15 N loads for 0%, 0.191%, and 0.304% niobium reinforcements, respectively. In the hardness tests, the highest measured value was observed in the sample reinforced with 0.304% niobium, with an average of 272 HB. Since Nb is an element with high hardness, the hardness values of the samples increased with the increase in Nb reinforcement. With an average value of 1411 MPa, the niobium-reinforced sample with 0.191% niobium reinforcement exhibited the highest compression strength. When analyzing the results of the compression tests, an increasing trend was observed with increasing reinforcement ratio, as was the case with the results of the hardness tests. In the wear tests, the changes in wear volume, wear rate, and friction coefficients were examined at loads of 5 N, 10 N, and 15 N. When the test specimens with the same reinforcement ratio were examined, it was found that the wear volume loss values increased with the increase in load. As the wear resistance increases with increasing hardness value, it becomes more difficult to detach the particles from the wear surfaces. The wear volume of the samples, therefore, decreases as the hardness value increases. At the end of the experimental study, a microstructural analysis of the surfaces subjected to sliding wear was carried out. It was observed that wear marks and pits had formed on the surfaces subjected to sliding wear.


  • Open Access

    The effect of niobium carbide coating on wear behavior of grey cast iron via thermo-reactive diffusion process

    by Rifat Yakut

    Wear is the limit for grey cast iron (GCI), which is utilized extensively in today’s industries. Coating the surface of a material can enhance its ability to withstand wear. In this study, thermo-reactive diffusion (TRD) process was used to coat the surface of grey cast iron with niobium carbide (NbC). The coatings were applied for 2, 4 and 6 hours at 950ºC and 1050ºC. The coated samples were subjected to metallographic examination to investigate the microstructure of the coating zone. For this purpose, optical microscopy examinations were carried out. Microhardness tests were carried out to assess the mechanical properties of the samples. The coated surfaces were analyzed using energy-dispersive X-ray spectrometry (EDS), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Wear tests were carried out on the coated surfaces to measure the volumetric wear loss, the wear rate and the changes in the coefficient of friction. Coating thickness rose as furnace waiting time increased, according to optical microstructures of coated surfaces. The hardness of the coated surfaces increased with a longer coating duration. Depending on the duration and temperature of the coating process, the layer thickness ranged from 6 to 52 µm. The lowest microhardness and the highest microhardness values of the coatings were determined at 950ºC for 2 hours and at 950ºC for 6 hours, respectively. Compared to the uncoated samples, the coated samples had a 6-9 times higher hardness value. In the abrasion tests, the loss of wear volume increased with increase in load.


  • Investigation of the Durability and Performance of Gears Made of Glass Fiber, Carbon and Bronze-Reinforced Polytetrafluoroethylene Matrix Composite Material

    by R. Yakut, H. Düzcükoğlu, H. Akkuş

    Polymer gears are often used in power transmission due to their numerous advantages. Heat accumulates on polymer gears during operation. Over time, this accumulated heat leads to damage; and shortens the service life of the gears. To prevent this, various fillers are added to the polymer materials. These fillers help to dissipate the heat generated on the gears. In this study, 25% glass fibers, 35% carbon powder, and 60% bronze particles were added to the polytetrafluoroethylene (PTFE) matrix to determine the wear behavior of gears. The properties of the matrix and the filler mainly influence the wear behavior of PTFE composites. The study showed that all composite gears with filler have better wear resistance than pure PTFE gears due to their better thermal stability. After the tests, it was found that the gears made of PTFE + 35% carbon additive had about 12 times better wear rates than those made of pure PTFE. Based on the average temperature values of the experiment, it was found that the mass temperature of gears made of 35% carbon-doped PTFE is about 38-39% lower than that of pure PTFE. This study contributes to the standard studies on heat build-up, thermal damage, and wear of gears made of polymers with different fillers and ratios.


  • Open Access

    Investigation of Mechanical Properties of Grey Cast Irons Reinforced with Carbon Titanium Nitride (TiNC)

    by Rifat Yakut

    In this study, grey cast iron (GG25) was produced via reinforcement with carbon titanium nitride (TiNC) in different amounts (0%, 0.153%, 0.204% and 0.255%). Samples were made from this material according to the standards for hardness, compression and wear, and then experiments were conducted. The test conditions applied for the TiNC-reinforced samples were similarly applied to unreinforced samples. The TiNC-reinforced and unreinforced samples were compared regarding their compression, hardness, and wear properties. The results of the hardness tests showed the highest average hardness value of 215 HB for sample A (0% TiNC). For TiNC-reinforced specimens, the hardness values of the reinforced specimens increased with increasing reinforcement. Sample B (0.153% TiNC) had an average hardness value of 193 HB. For sample C (0.204% TiNC), an average hardness value of 200 HB was measured. For sample D (0.255% TiNC), an average hardness value of 204 HB was determined. Sample A’s highest compression strength value was 780 MPA (0% TiNC). Similar to the hardness test values, the compression strength of the reinforced samples increased with the increasing reinforcement rate. The compression test value was found to be 747 MPa for sample B (0.153% TiNC), 765 MPa for sample C (0.204% TiNC) and 778 MPa for sample D (0.255% TiNC). Wear tests were performed on all samples to examine changes in the wear volume loss, wear rate and friction coefficients. Scanning electron microscopy (SEM) was used to determine the wear mechanisms on the worn surfaces of the samples. When examining the wear condition of the samples with the same hardness value as a function of increasing load values, increases in the wear volume loss values were observed as the load value increased.


  • Open Access

    Investigation of the Effect of Additional Zirconium Diboride (ZrB2) in Spherical Graphite Cast Iron on Mechanical Properties

    by Rifat Yakut, Ramazan Ortakaya

    Steering gearbox bodies, which are produced from spheroidal graphite cast iron, experience wear and gaps over time since they operate under load. It is important to strengthen steering gearbox bodies to avoid this. In this study, a steering gearbox body was produced from a spheroidal graphite cast iron material with zirconium diboride at varying rates (0%, 0.227%, 0.455%, and 1.364%). Samples of the material were prepared according to established standards for hardness, compressive strength, and wear resistance tests. The mechanical properties of test samples with and without zirconium diboride (hardness, compressive strength, and wear resistance) were compared. Sample C showed the highest hardness measurement of 243 HB after adding 0.455% zirconium diboride. As the rate of addition increased, the values obtained from the hardness measurement test also increased. Sample C had the highest compressive value of 1438 MPa, with a 0.455% addition rate. It was found that the compressive strength values also increased as the addition rate increased. Wear tests were conducted to analyse wear volume, wear rate, and friction coefficients. A scanning electron microscope (SEM) device was utilised to identify wear mechanisms on the worn surfaces of the samples. Per the results of this study, wear volume values were found to increase with the load value.


  • Open Access

    Investigation of the microstructure, hardness, and compressive properties of TaC-reinforced lamellar graphite cast irons

    by Rifat Yakut, Ömer Çi̇ftçi̇

    Tantalum Carbide (TaC) reinforcement was made to lamellar graphite (gray) cast irons that were produced in the physical conditions of a foundry at reinforcement ratios of 0%, 0.025%, 0.155%, and 0.285%. Samples complying with standards were prepared using the TaC-reinforced lamellar graphite (gray) cast iron alloys that were produced, and Brinell hardness tests, compressive strength tests, and microstructural analyses were conducted. According to the test results, the highest average Brinell hardness value was found as 231 HB in sample A which was reinforced at a ratio of 0.025%. In general, as the reinforcement ratio increased, there was an increase in the hardness test measurement results. The highest average compressive strength value was found as 949 MPa in sample C which was reinforced at a ratio of 0.285%. In general, as the reinforcement ratio increased, there was an increase in the compressive strength values. The results of the microstructural analyses showed that the reinforcement material was dispersed into the matrix.


  • The Effects of Different Reinforcement Ratios on Wear Behaviors in EN AW 5754 (AlMg3)/SiCp Composite Materials Produced with the Squeeze Casting Method

    by Vedat Taşkin, Cuma Kiliç, Rifat Yakut, Nilhan Ürkmez Taşkin

    In this study, SiCp particles were reinforced at volumetric ratios of 5%, 10%, 15% and 20% into the EN AW 5756 (AlMg3) metal matrix composite by using the squeeze casting method. The squeezing process was carried out for 10 seconds under a pressure of 80 MPa. The changes in the wear behaviors and friction coefficients of the EN AW 5754/SiCp composite samples were examined under1.0 N force, 5000 cycles and with a 0.04 m/s sliding speed. As a result of the experiments, it was found that the friction coefficient value increased from the non-reinforced alloy to the 10% SiCp-reinforced composite, while it then decreased in the 15% and 20% SiCp-reinforced composites. Moreover, the amount of wear in the composite material increased as the ratio of the reinforcement increased, and the highest wear occurred in the 10% SiCp-reinforced composite. This wear rate decreased in the 15% reinforced composite and then increased in the 20% reinforced composite. The deformation wear statuses of the composite materials that were used in the experiments were examined by conducting SEM (Scanning Electron Microscopy) and EDS (Energy-Dispersive Spectrometry) analyses. In these examinations, it was observed that the 5% and 10% SiCp reinforcements did not show a homogeneous distribution in the matrix, but the 15% and 20% SiCp reinforcements were homogeneously distributed in the matrix material.


  • Open Access

    PRODUCTION OF AA7075/B4C COMPOSITE MATERIALS BY SEMI-SOLID STIRRING METHOD

    by Rifat Yakut, Nilhan Ürkmez Taşkin

    AA7075 aluminum alloy was reinforced with B 4 C particles to produce aluminum composite materials. In the production of AA7075/B 4 C composite materials, semi-solid mixing methods were applied for homogen reinforcement dispersion then low pressure solidification. For the determination of the mechanical properties of the obtained samples; three point bending, compression and hardness tests were performed. In addition, microstructure, reinforcement matrix interface and chemical structure of the composite material produced by SEM, EDS, XRD analysis were examined. As a result, it was observed that; using the semi-solid mixing method the reinforcing powders could be distributed homogeneously into the matrix, both chemical and mechanical bonding could be occurs between the matrix and the reinforcing material and this mixing technique could be easily used in the production of particle reinforced metal composites.


  • Open Access

    Increasing the Lifetime of Variable Displacement Vane Pump with Aluminium Body

    by Ahmet Oktay Devecili, Rifat Yakut, Alper Tombak

    In this study, anodic oxidation method is applied to a flow-regulating valve and valve seat of the variable displacement vane pump with an aluminium body, which is used commonly in commercial vehicle steering systems. Then the lifetime of the pump is tested in a contaminated hydraulic fluid. After the lifetime tests, surfaces of the coatings are characterized with scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS). The thickness of the coating after the process is measured between 30 and 40 microns, and the hardness of the coating is between 360 and 440 Hv. This experiment proved that the resistance of the valve seat increased by between 30 and 40% after the coating process.