Mehmet Yılmaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mehmet Yılmaz has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Muhammed Fatih Çorapsız
Atatürk Universitesi
10 shared publications - Muhammed Mahho
Department of Electrical-Electronic Engineering, Ataturk University, Erzurum, Turkey
4 shared publications - Muhammed Reşit Çorapsız
Erzurum Teknik Universitesi
2 shared publications - Abdullah Başçi
Department of Electrical Engineering, Atatürk University
1 shared publication - Kaan Can
Faculty of Engineering, Department of Electrical and Electronics Engineering, Atatürk University, Erzurum, Turkey
1 shared publication - Muhammet Emin Kalçik
Agri Ibrahim Cecen Universitesi
1 shared publication
Latest Publications
- Open Access
- 29 April 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Real-time implementation of a new MPPT technique based on Shifted Hyperbolic Tangent Function under various weather conditions
In this study, a new Maximum Power Point Tracking (MPPT) algorithm is proposed for solar energy systems using the Particle Swarm Optimization (TF-IPSO) algorithm based on hyperbolic tangent function parameters. The disadvantages of the PSO algorithm are addressed by using hyperbolic tangent function parameters to update the acceleration coefficients and inertia weights of the proposed TF-IPSO algorithm. The proposed TF-IPSO algorithm is investigated for both partial shading conditions (PSC) conditions and variable radiation conditions with sudden changes in solar radiation. The TF-IPSO algorithm is compared with the most widely used metaheuristic optimization algorithms that demonstrate superior performance, such as Particle Swarm Optimization (PSO), Deterministic PSO (DPSO), Flower Pollination Algorithm (FPA), Improved Social spider optimization algorithm (ISSO), Hyperbolic Slime Mould Algorithm (HSMA) and EPSO algorithm based on shifted sigmoid function parameters Algorithm (ST-PSO). Simulation studies have shown that the proposed TF-IPSO algorithm outperforms similar methods by providing a high MPPT efficiency of 99.97%, fast tracking time, and low power emissions. Furthermore, the success of the proposed TF-IPSO algorithm has also been tested in real time implementation. For this purpose, the Chroma 62,020 H-150HS Solar Array Simulator was used. The performance of the TF-IPSO algorithm is evaluated under partial shading conditions using a PV system with a 4Sx2P connection. From the real-time results, it is observed that the proposed TF-IPSO algorithm has 1.28% higher MPPT efficiencies than the DPSO algorithm, 7.05% higher than the FPA, 0.42% higher than the HSMA, 2.4% higher than the ISSO, 2.31% higher than the PSO algorithm, and 1.18% higher than the ST-PSO algorithm. Simulation studies and results from real-time experiments show that the proposed MPPT method outperforms other metaheuristic algorithms and provides high efficiency by converging to the Maximum Power Point (MPP) under sudden changes in PSC and solar radiation.
- 29 April 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessReal-time implementation of a new MPPT technique based on Shifted Hyperbolic Tangent Function under various weather conditions
In this study, a new Maximum Power Point Tracking (MPPT) algorithm is proposed for solar energy systems using the Particle Swarm Optimization (TF-IPSO) algorithm based on hyperbolic tangent function parameters. The disadvantages of the PSO algorithm are addressed by using hyperbolic tangent function parameters to update the acceleration coefficients and inertia weights of the proposed TF-IPSO algorithm. The proposed TF-IPSO algorithm is investigated for both partial shading conditions (PSC) conditions and variable radiation conditions with sudden changes in solar radiation. The TF-IPSO algorithm is compared with the most widely used metaheuristic optimization algorithms that demonstrate superior performance, such as Particle Swarm Optimization (PSO), Deterministic PSO (DPSO), Flower Pollination Algorithm (FPA), Improved Social spider optimization algorithm (ISSO), Hyperbolic Slime Mould Algorithm (HSMA) and EPSO algorithm based on shifted sigmoid function parameters Algorithm (ST-PSO). Simulation studies have shown that the proposed TF-IPSO algorithm outperforms similar methods by providing a high MPPT efficiency of 99.97%, fast tracking time, and low power emissions. Furthermore, the success of the proposed TF-IPSO algorithm has also been tested in real time implementation. For this purpose, the Chroma 62,020 H-150HS Solar Array Simulator was used. The performance of the TF-IPSO algorithm is evaluated under partial shading conditions using a PV system with a 4Sx2P connection. From the real-time results, it is observed that the proposed TF-IPSO algorithm has 1.28% higher MPPT efficiencies than the DPSO algorithm, 7.05% higher than the FPA, 0.42% higher than the HSMA, 2.4% higher than the ISSO, 2.31% higher than the PSO algorithm, and 1.18% higher than the ST-PSO algorithm. Simulation studies and results from real-time experiments show that the proposed MPPT method outperforms other metaheuristic algorithms and provides high efficiency by converging to the Maximum Power Point (MPP) under sudden changes in PSC and solar radiation.
- Open Access
- 11 April 2026
- Published by Bursa Technical University in Journal of Innovative Science and Engineering
- Vol. 10 (1) , 189-200
Modeling Turkey’s Hourly Electricity Market Clearing Prices Using Exponential Gaussian Process Regression
In the electricity market, the Market Clearing Price (MCP) holds strategic importance for both producers and consumers, as it represents the price formed at the equilibrium point of supply and demand. Accurate prediction of the MCP is critical for market participants in terms of production planning, cost estimation, and risk management processes. In this study, modeling was performed using four different machine learning (ML) methods, namely Exponential Gaussian Process Regression (EGPR), Rational Quadratic Gaussian Process Regression (RGPR), Quadratic Support Vector Machine (QSVM) and Medium Gaussian Support Vector Machine (MGSVM), in order to estimate the MCP in the Turkish Day Ahead Market (DAM). A total of 4001 data points were used for the training phase. Two methods were used to prove the robustness and generalizability of the models. These are: 10-fold cross-validation method, and testing with a data set (25 points) completely independent of the training data. The data used in the modeling process include real-time electricity consumption (MWh), hourly electricity generation by source (natural gas, hydroelectric power plants (DAM), lignite, run-of-river, solar energy), Purchase/Sale Bid Volume, Matched Purchase/Sale Quantity and U.S. Dollar Exchange Rate. The performances of machine learning methods were compared according to performance criteria such as Root Mean Square Error (RMSE), Mean Square Error (MSE), Mean Absolute Error (MAE) and Coefficient of Determination (R²). It was observed that the model created with EGPR had the highest R2 value of “0.908” and “0.913” for 10-fold cross-validation and an independent test dataset, respectively. In addition, it was obtained that the MSE, RMSE and MAE error metrics for the 10-fold cross-validation of the model created with EGPR were the lowest with 26026.20, 161.33 and 120.33, respectively. For the independent test dataset, the MSE, RMSE, and MAE error metrics were 7734, 87.94, and 61.56, respectively, resulting in lower prediction errors than other ML methods. It was observed from both the 10-fold cross-validation results and the independent test dataset results that the model created with EGPR made more successful predictions than the models created with RGPR, QSVM and MGSVM.
- 11 April 2026
- Published by Bursa Technical University in Journal of Innovative Science and Engineering
- Vol. 10 (1) , 189-200
Open AccessModeling Turkey’s Hourly Electricity Market Clearing Prices Using Exponential Gaussian Process Regression
In the electricity market, the Market Clearing Price (MCP) holds strategic importance for both producers and consumers, as it represents the price formed at the equilibrium point of supply and demand. Accurate prediction of the MCP is critical for market participants in terms of production planning, cost estimation, and risk management processes. In this study, modeling was performed using four different machine learning (ML) methods, namely Exponential Gaussian Process Regression (EGPR), Rational Quadratic Gaussian Process Regression (RGPR), Quadratic Support Vector Machine (QSVM) and Medium Gaussian Support Vector Machine (MGSVM), in order to estimate the MCP in the Turkish Day Ahead Market (DAM). A total of 4001 data points were used for the training phase. Two methods were used to prove the robustness and generalizability of the models. These are: 10-fold cross-validation method, and testing with a data set (25 points) completely independent of the training data. The data used in the modeling process include real-time electricity consumption (MWh), hourly electricity generation by source (natural gas, hydroelectric power plants (DAM), lignite, run-of-river, solar energy), Purchase/Sale Bid Volume, Matched Purchase/Sale Quantity and U.S. Dollar Exchange Rate. The performances of machine learning methods were compared according to performance criteria such as Root Mean Square Error (RMSE), Mean Square Error (MSE), Mean Absolute Error (MAE) and Coefficient of Determination (R²). It was observed that the model created with EGPR had the highest R2 value of “0.908” and “0.913” for 10-fold cross-validation and an independent test dataset, respectively. In addition, it was obtained that the MSE, RMSE and MAE error metrics for the 10-fold cross-validation of the model created with EGPR were the lowest with 26026.20, 161.33 and 120.33, respectively. For the independent test dataset, the MSE, RMSE, and MAE error metrics were 7734, 87.94, and 61.56, respectively, resulting in lower prediction errors than other ML methods. It was observed from both the 10-fold cross-validation results and the independent test dataset results that the model created with EGPR made more successful predictions than the models created with RGPR, QSVM and MGSVM.
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Energy Research
- Vol. 2026 (1) , 6690568
Walrus Optimization Algorithm for Multi‐MPP Tracking Under Harsh and Variable Conditions: Simulation and Real‐Time Validation
Renewable energy sources, especially solar energy, have seen a significant increase in installed capacity worldwide in recent years compared to other renewable energy sources. In solar energy systems, maximum power point (MPP) tracking (MPPT) algorithms are used to transfer the power obtained from the panel to the load/grid at the highest possible level. Classical MPPT algorithms track local maximum power points (LMPPs) under partial shading conditions (PSC). In many metaheuristic optimization algorithms, the behavior of searching for the optimum solution is determined by fixed or predefined rules. In this study, simulation and real‐time testing of the walrus optimization algorithm (WaOA), which has been reported in the literature as a promising algorithm with a good exploration–exploitation balance and the potential for relatively low sensitivity to parameter settings, are carried out for photovoltaic (PV) systems. Two different scenarios were evaluated in simulation studies. In the first scenario, an off‐grid PV system was evaluated under five different partial shading and rapidly changing environmental conditions. In the second scenario, the proposed WaOA algorithm was tested for grid‐connected PV systems under two different scenarios. Furthermore, the performance of WaOA in PV systems has been experimentally verified through real‐time tests using the Chroma 62020H‐150S Solar Array Simulator. Both in the simulation studies and in real‐time tests, it is observed that WaOA showed high success in PV systems.
- 1 January 2026
- Published by Wiley in International Journal of Energy Research
- Vol. 2026 (1) , 6690568
Open AccessWalrus Optimization Algorithm for Multi‐MPP Tracking Under Harsh and Variable Conditions: Simulation and Real‐Time Validation
Renewable energy sources, especially solar energy, have seen a significant increase in installed capacity worldwide in recent years compared to other renewable energy sources. In solar energy systems, maximum power point (MPP) tracking (MPPT) algorithms are used to transfer the power obtained from the panel to the load/grid at the highest possible level. Classical MPPT algorithms track local maximum power points (LMPPs) under partial shading conditions (PSC). In many metaheuristic optimization algorithms, the behavior of searching for the optimum solution is determined by fixed or predefined rules. In this study, simulation and real‐time testing of the walrus optimization algorithm (WaOA), which has been reported in the literature as a promising algorithm with a good exploration–exploitation balance and the potential for relatively low sensitivity to parameter settings, are carried out for photovoltaic (PV) systems. Two different scenarios were evaluated in simulation studies. In the first scenario, an off‐grid PV system was evaluated under five different partial shading and rapidly changing environmental conditions. In the second scenario, the proposed WaOA algorithm was tested for grid‐connected PV systems under two different scenarios. Furthermore, the performance of WaOA in PV systems has been experimentally verified through real‐time tests using the Chroma 62020H‐150S Solar Array Simulator. Both in the simulation studies and in real‐time tests, it is observed that WaOA showed high success in PV systems.
- Open Access
- 2 October 2025
- Published by Elsevier in SSRN Electronic Journal
Real-time implementation of a new MPPT technique based on Shifted Hyperbolic Tangent Function under various weather conditions
In this study, a new maximum power point tracking (MPPT) algorithm is proposed for solar energy systems using the Particle Swarm Optimization (TF-IPSO) algorithm based on tangent function parameters. The disadvantages of the PSO algorithm are addressed by using tangent function parameters to update the acceleration coefficients and inertia weights of the proposed TF-IPSO algorithm. The proposed TF-IPSO algorithm is investigated for both partial shading (PSC) conditions and variable irradiance conditions with sudden changes in solar irradiance. The TF-IPSO algorithm is tested and compared with the most widely used metaheuristic optimization algorithms that demonstrate superior performance, such as PSO, Deterministic PSO (DPSO), Flower Pollination Algorithm (FPA), and Self-Tuning PSO (ST-PSO). The results obtained from the tests show that the proposed MPPT method outperforms other metaheuristic algorithms and provides high efficiency by converging to the Maximum Power Point (MPP) under sudden changes in PSC and solar irradiance. Simulation studies have shown that the proposed TF-IPSO algorithm outperforms similar methods by providing a high MPPT efficiency of 99.97%, fast tracking time, and low power emissions. The success of the TF-IPSO algorithm was also tested in real-time. For this purpose, the Chroma 62020H-150HS Solar Array Simulator was used. The performance of the TF-IPSO algorithm was evaluated under partial shading conditions using a PV system with a 4Sx2P connection. From the real-time results, it was observed that the proposed TF-IPSO algorithm has 1.28% higher MPPT efficiencies than the DPSO algorithm, 7.05% higher than the FPA algorithm, 2.31% higher than the PSO algorithm, and 1.18% higher than the ST-PSO algorithm.
- 2 October 2025
- Published by Elsevier in SSRN Electronic Journal
Open AccessReal-time implementation of a new MPPT technique based on Shifted Hyperbolic Tangent Function under various weather conditions
In this study, a new maximum power point tracking (MPPT) algorithm is proposed for solar energy systems using the Particle Swarm Optimization (TF-IPSO) algorithm based on tangent function parameters. The disadvantages of the PSO algorithm are addressed by using tangent function parameters to update the acceleration coefficients and inertia weights of the proposed TF-IPSO algorithm. The proposed TF-IPSO algorithm is investigated for both partial shading (PSC) conditions and variable irradiance conditions with sudden changes in solar irradiance. The TF-IPSO algorithm is tested and compared with the most widely used metaheuristic optimization algorithms that demonstrate superior performance, such as PSO, Deterministic PSO (DPSO), Flower Pollination Algorithm (FPA), and Self-Tuning PSO (ST-PSO). The results obtained from the tests show that the proposed MPPT method outperforms other metaheuristic algorithms and provides high efficiency by converging to the Maximum Power Point (MPP) under sudden changes in PSC and solar irradiance. Simulation studies have shown that the proposed TF-IPSO algorithm outperforms similar methods by providing a high MPPT efficiency of 99.97%, fast tracking time, and low power emissions. The success of the TF-IPSO algorithm was also tested in real-time. For this purpose, the Chroma 62020H-150HS Solar Array Simulator was used. The performance of the TF-IPSO algorithm was evaluated under partial shading conditions using a PV system with a 4Sx2P connection. From the real-time results, it was observed that the proposed TF-IPSO algorithm has 1.28% higher MPPT efficiencies than the DPSO algorithm, 7.05% higher than the FPA algorithm, 2.31% higher than the PSO algorithm, and 1.18% higher than the ST-PSO algorithm.
- 26 September 2025
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 14 (3) , 57-66
Performance Evaluation of a Nature-Inspired Three-Particle Swarm Optimization Algorithm in PV Systems with a Modified SEPIC Converter
The increase in world population, the development of industrialization and people's use of more advanced technologies increase energy demands day by day. People have started to turn to alternative energy sources to avoid the energy crisis that will occur when existing energy sources are exhausted. Photovoltaic (PV) systems are an advantageous option among sustainable energy sources. PV systems are affected by irradiance intensity and temperature. To overcome this problem, Maximum power point tracking (MPPT) algorithms are used. In this study, in order to maximize the efficiency of PV systems, the performance of Particle swarm optimization (PSO), Deterministic Particle swarm optimization (DPSO), Enhance Autonomous Group Particle swarm optimization (EAGPSO) algorithms were evaluated by using a high gain modified SEPIC converter. PSO, DPSO and EAGPSO algorithms were evaluated for three different scenarios under normal irradiance and partial shading conditions. It has been observed that the EAGPSO algorithm has the highest MPPT efficiency of 98.9% and a convergence time of 0.37s for different scenarios. In addition, it has been found that the power oscillation of the EAGPSO algorithm is reduced by approximately half compared to DPSO and by approximately two thirds compared to PSO.
- 26 September 2025
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 14 (3) , 57-66
Performance Evaluation of a Nature-Inspired Three-Particle Swarm Optimization Algorithm in PV Systems with a Modified SEPIC Converter
The increase in world population, the development of industrialization and people's use of more advanced technologies increase energy demands day by day. People have started to turn to alternative energy sources to avoid the energy crisis that will occur when existing energy sources are exhausted. Photovoltaic (PV) systems are an advantageous option among sustainable energy sources. PV systems are affected by irradiance intensity and temperature. To overcome this problem, Maximum power point tracking (MPPT) algorithms are used. In this study, in order to maximize the efficiency of PV systems, the performance of Particle swarm optimization (PSO), Deterministic Particle swarm optimization (DPSO), Enhance Autonomous Group Particle swarm optimization (EAGPSO) algorithms were evaluated by using a high gain modified SEPIC converter. PSO, DPSO and EAGPSO algorithms were evaluated for three different scenarios under normal irradiance and partial shading conditions. It has been observed that the EAGPSO algorithm has the highest MPPT efficiency of 98.9% and a convergence time of 0.37s for different scenarios. In addition, it has been found that the power oscillation of the EAGPSO algorithm is reduced by approximately half compared to DPSO and by approximately two thirds compared to PSO.
- Open Access
- 1 June 2024
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 14 (2) , 706-717
Mitigation of Power Unbalance in Electrical Distribution Transformers with Solar Photovoltaic Panels
In this article, a design is proposed to improve the power unbalance between the phases of three-phase electricity distribution transformers with the help of photovoltaic (PV) solar panels to be mounted on the roof of transformer centers. Simulation studies of the design were performed via MATLAB/Simulink and simulation results were observed and compared with real-time phase current data from four transformer centers. In the Transfer Switcher and Control System (TSCS) algorithm developed in the design, the percentage current unbalance rate (PCUR%) of the transformer is determined and the power produced from the PV panels is injected into the appropriate phase of the transformer. Phase lock loop (PLL) is used to ensure this connection occurs smoothly. In this study, performance analysis was made based on simulation results for the phase unbalance seen in the transformer before TSCS was activated and for the phase unbalance seen in the transformer after TSCS was activated. In simulation studies conducted on real-time data taken from a total of four transformers in Erzurum, Ağrı and Erzincan provinces, it was seen that the proposed approach had a reducing effect on the power unbalance in the transformer. In addition, approximately 3.6 kW of additional energy is provided to the distribution system for each transformer. In addition, it has been observed that the average current values drawn from the transformers has also decreased.
- 1 June 2024
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 14 (2) , 706-717
Open AccessMitigation of Power Unbalance in Electrical Distribution Transformers with Solar Photovoltaic Panels
In this article, a design is proposed to improve the power unbalance between the phases of three-phase electricity distribution transformers with the help of photovoltaic (PV) solar panels to be mounted on the roof of transformer centers. Simulation studies of the design were performed via MATLAB/Simulink and simulation results were observed and compared with real-time phase current data from four transformer centers. In the Transfer Switcher and Control System (TSCS) algorithm developed in the design, the percentage current unbalance rate (PCUR%) of the transformer is determined and the power produced from the PV panels is injected into the appropriate phase of the transformer. Phase lock loop (PLL) is used to ensure this connection occurs smoothly. In this study, performance analysis was made based on simulation results for the phase unbalance seen in the transformer before TSCS was activated and for the phase unbalance seen in the transformer after TSCS was activated. In simulation studies conducted on real-time data taken from a total of four transformers in Erzurum, Ağrı and Erzincan provinces, it was seen that the proposed approach had a reducing effect on the power unbalance in the transformer. In addition, approximately 3.6 kW of additional energy is provided to the distribution system for each transformer. In addition, it has been observed that the average current values drawn from the transformers has also decreased.
- Open Access
- 26 March 2024
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 13 (1) , 88-97
PSO Training Neural Network MPPT with CUK Converter Topology for Stand-Alone PV Systems Under Varying Load and Climatic Conditions
Temperature and irradiance levels are two examples of environmental variables that affect the power value produced by photovoltaic panels. Therefore, in order to transfer the maximum power value from the PV panel to the load under varying climatic conditions, maximum power point tracking (MPPT) algorithms and DC-DC converter topologies are used. In this study, the performances of boost converter and CUK converter circuit topologies are investigated under variable irradiance and variable load conditions by using a neural network-based MPPT algorithm learning particle swarm optimization (PSO). As the first scenario, it is analyzed assuming that the temperature and irradiance values coming to the panel are constant. As the second scenario, the performance evaluation of the converter topologies according to the current, voltage and power parameters is made for the variable load situation. As the last scenario, the difference in the irradiance value coming to the panel depending on the sun's condition during the day has been examined. Canadian Solar CS6P-250P PV panel is used in the study. 50 kHz is selected as the switching frequency. According to the results obtained, it has been observed that the CUK converter circuit topology reaches the maximum power point faster than the boost converter circuit topology both in dynamic environmental conditions and load change, and the oscillation at this point is less. It is aimed to increase the performance of this method, which uses boost converter topology and MPPT in the literature, by applying CUK converter topology.
- 26 March 2024
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 13 (1) , 88-97
Open AccessPSO Training Neural Network MPPT with CUK Converter Topology for Stand-Alone PV Systems Under Varying Load and Climatic Conditions
Temperature and irradiance levels are two examples of environmental variables that affect the power value produced by photovoltaic panels. Therefore, in order to transfer the maximum power value from the PV panel to the load under varying climatic conditions, maximum power point tracking (MPPT) algorithms and DC-DC converter topologies are used. In this study, the performances of boost converter and CUK converter circuit topologies are investigated under variable irradiance and variable load conditions by using a neural network-based MPPT algorithm learning particle swarm optimization (PSO). As the first scenario, it is analyzed assuming that the temperature and irradiance values coming to the panel are constant. As the second scenario, the performance evaluation of the converter topologies according to the current, voltage and power parameters is made for the variable load situation. As the last scenario, the difference in the irradiance value coming to the panel depending on the sun's condition during the day has been examined. Canadian Solar CS6P-250P PV panel is used in the study. 50 kHz is selected as the switching frequency. According to the results obtained, it has been observed that the CUK converter circuit topology reaches the maximum power point faster than the boost converter circuit topology both in dynamic environmental conditions and load change, and the oscillation at this point is less. It is aimed to increase the performance of this method, which uses boost converter topology and MPPT in the literature, by applying CUK converter topology.
- 30 June 2022
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 9 (1) , 195-207
Sliding-Mode Control Techniques of SEPIC Converter in Continuous Current Mode
Nowadays, direct current (DC) voltage is required for the operation of the machines used in many industrial applications. DC voltage generating photovoltaic (PV) panels or other DC voltage generators need to be converted from the voltage level produced by the DC voltage levels required for the operation of the machines. The conversion of a DC voltage to a different DC voltage is performed by DC-DC converters. The most commonly used DC-DC converters in the literature are buck, boost, buck-boost, CUK and SEPIC converter. In this study, different control methods are used in order to reach the desired voltage level of the output voltage of the equivalent series resistance and ideal SEPIC converter in continuous current mode. Conventional Proportional-Integral (PI) and Sliding Mode Control (SMC) methods are used to ensure that the converter reaches the desired voltage level. PI controller parameter values are calculated according to trial and error method. In order to compare the performances of the controller used in the case ideal and equivalent series resistance cases, the controller parameters are taken the same. SMC is shown to perform better in ideal and equivalent series resistance SEPIC converter compared to the traditional PI controller from simulation results. Besides, modeling and controller applications of SEPIC converter are realized by using MATLAB / SIMULINK program.
- 30 June 2022
- Published by Bilecik Seyh Edebali Universitesi Fen Bilimleri Dergisi in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
- Vol. 9 (1) , 195-207
Sliding-Mode Control Techniques of SEPIC Converter in Continuous Current Mode
Nowadays, direct current (DC) voltage is required for the operation of the machines used in many industrial applications. DC voltage generating photovoltaic (PV) panels or other DC voltage generators need to be converted from the voltage level produced by the DC voltage levels required for the operation of the machines. The conversion of a DC voltage to a different DC voltage is performed by DC-DC converters. The most commonly used DC-DC converters in the literature are buck, boost, buck-boost, CUK and SEPIC converter. In this study, different control methods are used in order to reach the desired voltage level of the output voltage of the equivalent series resistance and ideal SEPIC converter in continuous current mode. Conventional Proportional-Integral (PI) and Sliding Mode Control (SMC) methods are used to ensure that the converter reaches the desired voltage level. PI controller parameter values are calculated according to trial and error method. In order to compare the performances of the controller used in the case ideal and equivalent series resistance cases, the controller parameters are taken the same. SMC is shown to perform better in ideal and equivalent series resistance SEPIC converter compared to the traditional PI controller from simulation results. Besides, modeling and controller applications of SEPIC converter are realized by using MATLAB / SIMULINK program.
- 27 March 2022
- Published by Erzincan Universitesi Fen Bilimleri Ensitusu Dergisi in Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 15 (1) , 242-257
Artificial Neural Network based MPPT Algorithm with Boost Converter topology for Stand-Alone PV System
The increasing energy need in parallel with the technology development and the depletion of the resources have increased the importance of alternative energy resources. Solar energy systems are frequently preferred due to their advantages such as not having moving parts, being reliable and working without noise. Production of electricity from solar energy is obtained by serial or parallel connection of photovoltaic (PV) panels, depending on the desired voltage and current values. DC-DC converters are used to convert the energy obtained from the PV panels to the desired grid values. Maximum power point tracking (MPPT) algorithms are used in order to obtain the highest possible efficiency from the PV panels. MPPT algorithms control the duty period (D) ratio of DC-DC converters and obtain maximum energy. In this study, an Artificial Neural Network (ANN) based MPPT algorithm is proposed. Firstly, the temperature and irradiance data at the PV panel input are trained using the Levenberg-Marquardt algorithm. As a result, a reference voltage is generated and MPPT is realized by comparing it with the voltage produced by the PV panel. In order to evaluate the performance of the proposed algorithm, it is compared with the traditional MPPT methods such as Perturb & Observe (P&O) and Incremental Conductance (INC). As a result of the simulation studies, it has been observed that ANN based MPPT is more successful than P&O and INC algorithms for several irradiance and temperature conditions.
- 27 March 2022
- Published by Erzincan Universitesi Fen Bilimleri Ensitusu Dergisi in Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 15 (1) , 242-257
Artificial Neural Network based MPPT Algorithm with Boost Converter topology for Stand-Alone PV System
The increasing energy need in parallel with the technology development and the depletion of the resources have increased the importance of alternative energy resources. Solar energy systems are frequently preferred due to their advantages such as not having moving parts, being reliable and working without noise. Production of electricity from solar energy is obtained by serial or parallel connection of photovoltaic (PV) panels, depending on the desired voltage and current values. DC-DC converters are used to convert the energy obtained from the PV panels to the desired grid values. Maximum power point tracking (MPPT) algorithms are used in order to obtain the highest possible efficiency from the PV panels. MPPT algorithms control the duty period (D) ratio of DC-DC converters and obtain maximum energy. In this study, an Artificial Neural Network (ANN) based MPPT algorithm is proposed. Firstly, the temperature and irradiance data at the PV panel input are trained using the Levenberg-Marquardt algorithm. As a result, a reference voltage is generated and MPPT is realized by comparing it with the voltage produced by the PV panel. In order to evaluate the performance of the proposed algorithm, it is compared with the traditional MPPT methods such as Perturb & Observe (P&O) and Incremental Conductance (INC). As a result of the simulation studies, it has been observed that ANN based MPPT is more successful than P&O and INC algorithms for several irradiance and temperature conditions.