HYHakan Yurtkuran

Hakan Yurtkuran

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hakan Yurtkuran has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental Evaluation of Surface Roughness and Cutting Forces in Turning of 1.2379 Tool Steel: Role of Cutting Parameters and Tool Nose Radius

    by Hakan Yurtkuran

    Machining performance in turning is governed by both cutting conditions and tool geometry. This study focuses on how cutting parameters and tool nose radius influence surface roughness and cutting forces during the machining of 1.2379 (X153CrMoV12) cold work tool steel. Two tool cutting-edge nose radius values of 0.2 mm and 0.8 mm were considered under different combinations of feed rate, cutting speed, and depth of cut. Surface roughness and cutting force data obtained from the experiments were analyzed using statistical and graphical approaches, including response surface evaluation and variance analysis. The results showed that feed rate plays a leading role in determining surface roughness, while cutting speed has a secondary influence and depth of cut remains limited in effect. Regarding the cutting forces, both feed rate and depth of cut contributed significantly, whereas cutting speed had a relatively minor impact. Similar trends were observed for both tool nose radius. Although a larger radius resulted in slightly higher cutting forces, its overall influence on machining performance was not pronounced. The findings indicate that machining behavior is predominantly controlled by cutting parameters rather than tool geometry, and appropriate parameter selection is essential for achieving improved surface quality and efficient cutting performance.

  • Open Access

    Integrated assessment of tool wear, chip morphology, surface ıntegrity and energy consumption in sustainable milling of Inconel 718

    by Hakan Yurtkuran

    This study investigates the effects of four cooling/lubrication strategies (Dry, MQL, Cryogenic and Cryo-MQL) on the machinability of Inconel 718 during milling at cutting speeds of 40, 60 and 90 m/min. Power consumption, surface roughness, tool wear and chip morphology were systematically evaluated under constant feed rate and depth of cut. The results demonstrate that both cutting speed and cooling/lubrication strategy significantly influence machinability performance. Dry cutting resulted in the highest power consumption and the most severe tool wear due to excessive thermal and tribological loads. In contrast the Cryo-MQL strategy achieved up to 10% energy savings at low cutting speeds and exhibited consistently reduced tool wear across the investigated cutting conditions. Cryogenic cooling improved surface integrity at low cutting speeds while comparable surface roughness values were obtained for all strategies at higher cutting speeds due to improved thermal stability. Overall the findings indicate that Cryo-MQL provides favorable performance trends and practical advantages for milling of Inconel 718 by simultaneously reducing thermal and tribological effects within the investigated parameter range.


  • Optimisation of Energy Consumption in Milling of Inconel 718 Alloy and Prediction Model with Machine Learning

    by Hakan Yurtkuran, Güven Demirtaş, Birol Yazarlı, Ahmet Sertan Özpak, Semih Zorlu

    This study aims to optimize power consumption observed while milling Inconel 718 superalloy—well known for its poor machinability—and to develop machine learning-based prediction models. Experiments were carried out on a Taksan TMC 500 V CNC milling machining center at three cutting speeds (40, 60, and 90 m/min) under four distinct cutting conditions: dry, Minimum Quantity Lubrication (MQL), cryogenic, and cryogenic+MQL. Energy consumption was monitored in real-time using a KAEL Multiser signal analyzer and the collected data were analyzed through ANOVA and regression approaches. The ANOVA results revealed that cutting speed is the most significant factor influencing energy demand (p

  • Open Access

    Prediction of power consumption and its signals in sustainable turning of PH13-8Mo steel with different machine learning models

    by Hakan Yurtkuran, Mehmet Erdi Korkmaz, Munish Kumar Gupta, Hakan Yılmaz, Mustafa Günay, Govind Vashishtha

    Due to extensive distribution and huge demand of energy efficient processes, the energy-saving of machining processes draws more and more attention, and a significant variety of methods have evolved to prognosis or optimise the energy consumption in machining operations. Similarly, the estimation of power consumption-cutting conditions relationships is of great importance for optimizing processing costs and for cleaner machining. Compared to traditional methods, machine learning (ML) approach is one of the effective analysis options to model machinability indicators such as cutting force, tool wear, power consumption and surface quality. In this study, PH13-8Mo stainless steel was machined with coated carbide inserts using primarily Dry, MQL, nano-Graphene + MQL, nano-hBN + MQL, Cryo, Cryo + MQL cutting environments. Power consumption and its signals during milling were measured and different machine learning models were applied to estimate the Pc. To develop the Pc model based on the ML algorithm, 70% of the power consumption data is reserved for training and 30% for testing. In all cutting environments, power consumption increased by an average of 3.14% as feed speed increased. The reduction in Pc compared to the dry cutting was calculated as an average of 2.2%, 3.17%, 2.57%, 4.88% and 5.45% for MQL, nano-Graphen + MQL, nano-hBN + MQL, Cryo, Cryo + MQL, respectively. It is seen that the developed prediction model can reflect the power consumption-parameter relationships at high accuracy.


  • A State of the Art on Sustainable Metal Working Fluids in Machining Applications

    by Hakan Yurtkuran, Mustafa Günay, Ritu Rai

    Metalworking fluids (MWFs) play a crucial role in machining processes by lubricating and cooling cutting tools, reducing friction, and improving overall machining efficiency. These fluids can be classified into various types, including cutting oils, water-based fluids, and semi-synthetic or synthetic fluids. Cutting oils are often mineral-based, providing excellent lubrication in heavy-duty applications. Water-based fluids, on the other hand, are more environmentally friendly and commonly used in light to moderate machining operations. Semi-synthetic and synthetic fluids offer a balance between performance and eco-friendliness, incorporating additives to enhance their properties. Proper selection and management of MWFs are essential for optimizing tool life, surface finish, and overall productivity in metal machining applications. Research has shown that the cost of cutting fluid in machining constitutes 17% of the total production cost. In the same research, it was stated that the cutting tool cost was around 4%. This review provides an overview of the current advancements in sustainable MWFs within machining applications. It explores state-of-the-art technologies, formulations, and practices aimed at minimizing environmental impact while maintaining optimal performance in metalworking processes. The review encompasses eco-friendly additives, recycling methods, and emerging trends in the development of MWFs, emphasizing the importance of sustainable practices in the manufacturing industry.


  • Analyzing the Effects of Cutting Parameters on Machinability Criteria in Milling of 17-4PH Stainless Steel under Dry Environment

    by Hakan Yurtkuran, Mustafa Günay

    17-4 PH steel is a martensitic precipitation hardening stainless steel with an excellent convenience of good corrosion resistance and high mechanical properties. At the same time, it has been determined from the literature that very little research has been done on the milling of this steel, which is one of the materials that are difficult to process. Therefore, an experimental research was focused on the milling of the steel with coated carbide inserts in a dry cutting environment, which is an eco-friendly cutting regime. In the experiments performed with the up milling technique, the changes in the resultant cutting force (Fr), surface roughness (Ra) and total cutting power or energy consumption (PcT) during machining were investigated. Experiments were performed according to the L9 experimental design by choosing three different cutting speeds (V), feed rate (f) and cutting depth (ap). Fr values were calculated with the help of cutting force components measured with Kistler brand dynamometer and equipment. The magnitude of Fr mostly depends on the cutting depth (64.92%) and then the feed rate (30.26%), and it was determined that the forces relatively decreased with the increase in cutting speed. While Ra was mainly affected by the feed rate (65.52%), it was observed that the cutting speed had a substantial positive effect (33.78%). According to the PcT results, although the energy consumption owing to the spindle speed increased at high cutting speed without changing the chip cross-section, the decrease in material strength as a result of the increased cutting temperature led to a decrease in the total energy consumption. However, the lowest value was obtained at the smallest levels of the machining parameters. In the light of all the results, it is recommended to use optimized cutting parameters in industrial applications in terms of contributing to sustainability.


  • An Evaluation on Machinability Characteristics of Titanium and Nickel Based Superalloys Used in Aerospace Industry

    by Hakan Yurtkuran

    Superalloys are a group of materials that are commonly used in aerospace applications and are also called high temperature materials, as they have superior wear and corrosion resistance. Ni-based superalloys are used more often than Ti alloys in the aerospace industry as they have mechanical and physical properties such as superior temperature resistance and toughness, high corrosion resistance, excellent fatigue and creep resistance. Ti alloys, on the other hand, have the highest strength / weight ratio among metals, increasing their preference in these industries continuously. Casting, forging, powder metallurgy and machining methods are used in the process of shaping machine parts used in the aviation industry from superalloys. However, many components are mostly manufactured using machining methods due to the part geometry, desired size and surface quality requirements. In this context, in the production of parts from Ti alloys and Ni-based superalloys, which are difficult to process, the correct selection or optimization of processing parameters is very important in terms of minimization of processing costs and therefore sustainable manufacturing. In this study, criteria such as cutting tool quality, tool life, surface integrity and cooling / lubrication technology, which have an important place in the machinability of titanium and nickel-based superalloys, have been compiled based on current literature studies.


  • Open Access

    Sertleştirilmiş X40CrMoV5-1 Çeliğinin Tornalanmasında Kesme Kuvvetinin Deneysel ve Nümerik Olarak İncelenmesi

    by Nafiz Yaşar, Hakan Yurtkuran, Mustafa Günay

    En tr X40CrMoV5-1 hot work tool steel is commonly used in injection and extrusion molds and also manufacturing of parts requiring high temperature, toughness and abrasion resistance. On the other hand, the preference of hard turning instead of grinding reduces the production time and cost, while improving the fatigue strength of the part in the case of putting the cylindrical parts into final form. In this study, the main cutting force (Fc) was investigated experimentally and numerically during machining of hardened X40CrMoV5-1 tool steel with vacuum and heat treatment to 55 ± 1 HRC by coated and uncoated ceramic inserts. Hard turning experiments were performed according to the Taguchi L32 experimental design using different levels of feed rate, cutting speed and depth of cut. Kistler 9257B dynamometer and equipments were used in experimentally determination of Fc values. Cutting simulations based on the finite element method were performed in DEFORM 3D software. In addition, the effects of cutting parameter on Fc were identified via analysis of variance (ANOVA) at 95% confidence level. The similarity between experimental and numerical analysis results for Fc values ​​was found to be 94% for uncoated tools and 91% for coated tools. It was determined that depth of cut is the most significant factor according to ANOVA results obtained by using experimental data. X40CrMoV5-1 sıcak iş takım çeliği, enjeksiyon ve ekstrüzyon kalıplarında yüksek sıcaklık, tokluk ve aşınma direnci gerektiren parçaların imalatında yaygın olarak kullanılır. Diğer yandan, silindirik parçaların nihai geometriye getirilmesinde, taşlama yerine sert tornalamanın tercih edilmesi üretim zamanı ve maliyeti azaltırken, aynı zamanda parçanın yorulma mukavemetinde iyileşme sağlamaktadır. Bu çalışmada, vakumla ısıl işlemde 55±1 HRC'ye sertleştirilmiş X40CrMoV5-1 takım çeliğinin seramik kesici takımlar (kaplamalı ve kaplamasız) kullanılarak tornalanmasında elde edilen esas kesme kuvveti (Fc) değerleri deneysel ve nümerik olarak incelenmiştir. Sert tornalama deneyleri, kesme parametrelerinin (ilerleme hızı, kesme hızı ve kesme derinliği) farklı seviyeleri kullanılarak Taguchi L32 deney tasarımına göre gerçekleştirilmiştir. Fc değerlerinin deneysel olarak belirlenmesinde Kistler 9257B dinamometre ve ekipmanları kullanılmıştır. Sonlu elemanlar yöntemine dayalı olarak yapılan kesme simülasyonları DEFORM 3D yazılımında gerçekleştirilmiştir. Ayrıca, kesme parametrelerinin Fc üzerindeki etkileri %95 güven düzeyinde yapılan varyans analizi (ANOVA) ile belirlenmiştir. Fc değerleri için deneysel ve nümerik analiz sonuçları arasındaki benzerlik kaplamasız takımlar için ortalama %94, kaplamalı takımlar için %91 olarak bulunmuştur. Deneysel verilere dayanılarak yapılan ANOVA sonuçlarına göre en önemli faktörün kesme derinliği olduğu tespit edilmiştir.