Simona Breidokaite
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Simona Breidokaite has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Gediminas Stankunas
Lithuanian Energy Inst, Lab Nucl Installat Safety, Breslaujos Str 3, LT-44403 Kaunas, Lithuania
5 shared publications- Gediminas Stankunas
Lithuanian Energy Institute, Laboratory of Nuclear Installation Safety, Breslaujos str. 3, LT-44403 Kaunas, Lithuania
4 shared publications - Andrius Tidikas
Laboratory of Nuclear Installation Safety, Lithuanian Energy Institute, 44403 Kaunas, Lithuania
3 shared publications - Andrius Slavickas
Lithuanian Energy Institute
1 shared publication Andrius Tidikas
Lithuanian Energy Institute, Laboratory of Nuclear Installation Safety, Breslaujos str. 3, LT-44403, Kaunas, Lithuania
1 shared publication- Claudia Gasparrini
CNR, ENEA, INFN, Universit di Padova, Acciaierie Venete SpA, Consorzio RFX, Padua, Italy
1 shared publication
Latest Publications
- 24 July 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 206
Evaluation of the breeding material activation and radionuclide inventory analysis for EU DEMO
- 24 July 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 206
Evaluation of the breeding material activation and radionuclide inventory analysis for EU DEMO
- 22 May 2024
- Published by Elsevier in Applied Radiation and Isotopes
- Vol. 210, 111363
Neutron irradiation-induced shutdown dose rate estimation in EU DEMO divertor
- 22 May 2024
- Published by Elsevier in Applied Radiation and Isotopes
- Vol. 210, 111363
Neutron irradiation-induced shutdown dose rate estimation in EU DEMO divertor
- Open Access
- 22 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (7) , 2674
Activity and Dose Rate Calculations for Joint European Torus Outer Long-Term Irradiation Station during Tritium and Second Deuterium Tritium Experiment Campaigns
The Joint European Torus (JET) is playing an important role in preparing for the operation of the future world’s largest tokomak, ITER. In this respect, the tritium campaign (C40) and second deuterium–tritium experiment (DTE2, C41) took place in the JET during the years 2021 and 2022. In this work, a corresponding irradiation scenario was utilized for the activation calculations of eight material foils located at the JET outer long-term irradiation station (OLTIS). Neutron-induced activities and dose rates at a 30 cm distance after shutdown at specified cooling intervals were calculated with the FISPACT-II code, employing the EAF-2010 nuclear and TENDL-2021 data libraries. The Monte Carlo MCNP6.2 particle transport code equipped with the FENDL-3.1d nuclear data library was used for the calculation of the neutron flux densities.
- 22 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (7) , 2674
Open AccessActivity and Dose Rate Calculations for Joint European Torus Outer Long-Term Irradiation Station during Tritium and Second Deuterium Tritium Experiment Campaigns
The Joint European Torus (JET) is playing an important role in preparing for the operation of the future world’s largest tokomak, ITER. In this respect, the tritium campaign (C40) and second deuterium–tritium experiment (DTE2, C41) took place in the JET during the years 2021 and 2022. In this work, a corresponding irradiation scenario was utilized for the activation calculations of eight material foils located at the JET outer long-term irradiation station (OLTIS). Neutron-induced activities and dose rates at a 30 cm distance after shutdown at specified cooling intervals were calculated with the FISPACT-II code, employing the EAF-2010 nuclear and TENDL-2021 data libraries. The Monte Carlo MCNP6.2 particle transport code equipped with the FENDL-3.1d nuclear data library was used for the calculation of the neutron flux densities.
- 11 May 2023
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 210
Helium production and material damage rate assessment in EU DEMO HCPB divertor
- 11 May 2023
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 210
Helium production and material damage rate assessment in EU DEMO HCPB divertor
- 24 February 2023
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 42 (1) , 1-8
Neutronics assessment for Detailed Helium-Cooled And Water-Cooled DEMO Breeder Blanket Concepts
- 24 February 2023
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 42 (1) , 1-8
Neutronics assessment for Detailed Helium-Cooled And Water-Cooled DEMO Breeder Blanket Concepts
- 23 June 2022
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 41 (2) , 1-6
Neutron Flux in EU DEMO Divertor Cassette Body Using HCPB and WCLL Breeding Blanket Models
- 23 June 2022
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 41 (2) , 1-6
Neutron Flux in EU DEMO Divertor Cassette Body Using HCPB and WCLL Breeding Blanket Models
- Open Access
- 22 June 2022
- Published by MDPI AG in Environments
- Vol. 9 (7) , 76
Activated Corrosion Products Evaluations for Occupational Dose Mitigation in Nuclear Fusion Facilities
Activated corrosion products generation in primary heat transfer systems of nuclear fusion facilities is a relevant radiological source term for occupation dose assessments. The formation of the Chalk River Undefined Deposit, already well known in nuclear fission power plants, represents a significant safety issue in fusion applications due to the intense high energy neutron fluences (about 14 MeV in Deuterium-Tritium operation). The activated corrosion products formation is a multi-physical problem. The combined synergy of activation, corrosion, dissolution, erosion, ejection, precipitation, and transport phenomena induces the contamination of coolant loop regions located outside the bio-shield, where scheduled worker operation might take place. The following manuscript shows how activated corrosion products are evaluated for the nuclear fusion power plant design under investigation by the Safety and Environment Work Package (WPSAE) of the Eurofusion Consortium (i.e., the European Demonstration power plant, EU-DEMO). The major issues in activated corrosion products estimations are here exposed and the main results for mass and activity inventories are briefly shown for some main Primary Heat Transfer Systems of EU-DEMO.
- 22 June 2022
- Published by MDPI AG in Environments
- Vol. 9 (7) , 76
Open AccessActivated Corrosion Products Evaluations for Occupational Dose Mitigation in Nuclear Fusion Facilities
Activated corrosion products generation in primary heat transfer systems of nuclear fusion facilities is a relevant radiological source term for occupation dose assessments. The formation of the Chalk River Undefined Deposit, already well known in nuclear fission power plants, represents a significant safety issue in fusion applications due to the intense high energy neutron fluences (about 14 MeV in Deuterium-Tritium operation). The activated corrosion products formation is a multi-physical problem. The combined synergy of activation, corrosion, dissolution, erosion, ejection, precipitation, and transport phenomena induces the contamination of coolant loop regions located outside the bio-shield, where scheduled worker operation might take place. The following manuscript shows how activated corrosion products are evaluated for the nuclear fusion power plant design under investigation by the Safety and Environment Work Package (WPSAE) of the Eurofusion Consortium (i.e., the European Demonstration power plant, EU-DEMO). The major issues in activated corrosion products estimations are here exposed and the main results for mass and activity inventories are briefly shown for some main Primary Heat Transfer Systems of EU-DEMO.
- 7 June 2022
- Published by Elsevier in Applied Radiation and Isotopes
- Vol. 187, 110314
Activation analysis and evaluation of the radionuclide inventories, decay heat for European DEMO divertor components
- 7 June 2022
- Published by Elsevier in Applied Radiation and Isotopes
- Vol. 187, 110314
Activation analysis and evaluation of the radionuclide inventories, decay heat for European DEMO divertor components
- Open Access
Activities in Divertor Reflector and Linear Plates Using WCLL and HCPB Breeding Blanket Concepts
In fusion devices, such as European Demonstration Fusion Power Reactor (EU DEMO), primary neutrons can cause material activation due to the interaction between the source particles and the targeting material. Subsequently, the reactor’s inner components become activated. For safety and safe performance purposes, it is necessary to evaluate neutron-induced activities. Activities results from divertor reflector and liner plates are presented in this work. The purpose of liner shielding plates is to protect the vacuum vessel and magnet coils from neutrons. As for reflector plates, the function is to shield the cooling components under plasma-facing components from alpha particles, thermal effects, and impurities. Plates are made of Eurofer with a 3 mm layer of tungsten, while the water is used for cooling purposes. The calculations were performed using two EU DEMO MCNP (Monte Carlo N-Particles) models with different breeding blanket configurations: helium-cooled pebble bed (HCPB) and water-cooled lithium lead (WCLL). The TENDL–2017 nuclear data library has been used for activation reactions cross-sections and nuclear reactions. Activation calculations were performed using the FISPACT-II code at the end of irradiation for cooling times of 0 s–1000 years. Radionuclide analysis of divertor liner and reflector plates is also presented in this paper. The main radionuclides, with at least 1% contribution to the total value of activation characteristics, were identified for the previously mentioned cooling times.
Open AccessActivities in Divertor Reflector and Linear Plates Using WCLL and HCPB Breeding Blanket Concepts
In fusion devices, such as European Demonstration Fusion Power Reactor (EU DEMO), primary neutrons can cause material activation due to the interaction between the source particles and the targeting material. Subsequently, the reactor’s inner components become activated. For safety and safe performance purposes, it is necessary to evaluate neutron-induced activities. Activities results from divertor reflector and liner plates are presented in this work. The purpose of liner shielding plates is to protect the vacuum vessel and magnet coils from neutrons. As for reflector plates, the function is to shield the cooling components under plasma-facing components from alpha particles, thermal effects, and impurities. Plates are made of Eurofer with a 3 mm layer of tungsten, while the water is used for cooling purposes. The calculations were performed using two EU DEMO MCNP (Monte Carlo N-Particles) models with different breeding blanket configurations: helium-cooled pebble bed (HCPB) and water-cooled lithium lead (WCLL). The TENDL–2017 nuclear data library has been used for activation reactions cross-sections and nuclear reactions. Activation calculations were performed using the FISPACT-II code at the end of irradiation for cooling times of 0 s–1000 years. Radionuclide analysis of divertor liner and reflector plates is also presented in this paper. The main radionuclides, with at least 1% contribution to the total value of activation characteristics, were identified for the previously mentioned cooling times.
- Open Access
- 5 February 2020
- Published by Lithuanian Academy of Sciences in Lithuanian Journal of Physics
- Vol. 60 (1)
Activation of high flux test module sample holder after IFMIF-DONES operation
Nuclear safety assessment in nuclear fusion devices relies on the Monte Carlo method based neutron transport calculations. This paper presents information about the calculation results of the activities and dose rates caused by neuron irradiation for the structural materials of the high flux test module sample holder of IFMIF-DONES. The neutron induced activities and dose rates at shutdown were calculated by means of the FISPACT-2010 code with data from the EAF-2010 nuclear data library. Neutron fluxes and spectra were obtained with MCNP neutron transport calculations. The activities and dose rates were calculated at the end of irradiation of the assumed device operation scenario for cooling times of 0 s – 1000 year. In addition, radionuclides with contribution of at least 0.5% to the total value of activation characteristics at the previously mentioned cooling times were identified. After the operation, the most active radionuclide is 55Fe, with an activity share ranging from 30% (M200) to 63% (M8), and at the end of the prediction it accounts for 86% of the total activity. The highest dose rates at the end of irradiation are attributed to 56Mn radionuclide. 54Mn and 60Co are the most dominant radionuclides during intermediate and long cool-down periods.
- 5 February 2020
- Published by Lithuanian Academy of Sciences in Lithuanian Journal of Physics
- Vol. 60 (1)
Open AccessActivation of high flux test module sample holder after IFMIF-DONES operation
Nuclear safety assessment in nuclear fusion devices relies on the Monte Carlo method based neutron transport calculations. This paper presents information about the calculation results of the activities and dose rates caused by neuron irradiation for the structural materials of the high flux test module sample holder of IFMIF-DONES. The neutron induced activities and dose rates at shutdown were calculated by means of the FISPACT-2010 code with data from the EAF-2010 nuclear data library. Neutron fluxes and spectra were obtained with MCNP neutron transport calculations. The activities and dose rates were calculated at the end of irradiation of the assumed device operation scenario for cooling times of 0 s – 1000 year. In addition, radionuclides with contribution of at least 0.5% to the total value of activation characteristics at the previously mentioned cooling times were identified. After the operation, the most active radionuclide is 55Fe, with an activity share ranging from 30% (M200) to 63% (M8), and at the end of the prediction it accounts for 86% of the total activity. The highest dose rates at the end of irradiation are attributed to 56Mn radionuclide. 54Mn and 60Co are the most dominant radionuclides during intermediate and long cool-down periods.