ABAleyna Bayatlı

Aleyna Bayatlı

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Aleyna Bayatlı has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Correlation Between Boron Content, Microstructure, and Corrosion Resistance in Electroless Nickel Boron Coatings

    by Aleyna Bayatlı, Mustafa Kocabas

    Boron is the key element that plays a critical role in the surface characteristics of electroless nickel-boron (ENB) coatings. However, in literature, the influence of boron content has generally been investigated without considering equal coating thickness conditions. To eliminate the effect of coating thickness and better understand the role of boron content, coatings with equal thickness were produced by varying the deposition time and reducing agent concentration. For this purpose, in this study the total deposition time of 120 minutes (min) was divided into three intervals: (i) 0-25 min, (ii) 25-60 min, and (iii) 60-120 min, corresponding to the 1st, 2nd, and 3rd coating stages, respectively, in order to obtain three individual coatings with an equal thickness approximately 5 µm. In addition, coatings with different boron contents were produced as low-boron (LB), standard-boron (SB), and high-boron (HB) samples, again with constant coating thickness. These coatings were also compared with the combined 15 µm coating obtained after the total 120 min deposition period (1st + 2nd + 3rd stages). The layer-dependent behavior of ENB coatings was investigated for the first time in literature. The surface morphology, boron content, and corrosion behavior of the coatings were characterized using scanning electron microscopy (SEM), inductively coupled plasma-optical emission spectroscopy (ICP-OES), and electrochemical corrosion analyses. The results showed that increasing the reducing agent concentration promoted hydrogen evolution and coating porosity. Therefore, the 1st layer and HB coatings exhibited a rougher cauliflower-type morphology with smaller nodules and higher porosity. In contrast, the 3rd layer and LB coatings exhibited a denser and more homogeneous microstructure with improved corrosion resistance compared to the other groups (1st-2nd layers and HB-SB coatings, respectively). Overall, the findings indicate that the corrosion resistance of ENB coatings is not governed solely by boron content, but is also strongly influenced by hydrogen evolution, porosity, and microstructural homogeneity.

  • Open Access

    Konya Gevale Kalesi Kazılarında Bulunan Temrenlerin Arkeometalurjik İncelemeleri

    by Erkan Aygör, Aleyna Bayatlı, Musafa Kocabaş

    Türkiye’de Orta Çağ kazılarında çıkarılan ve Orta Çağ’a ait temrenler üzerine çalışmalar oldukça sınırlıdır. Özellikle Orta Çağ’da, temrenlerin bilinmeyen yönleri bulunmaktadır. Bu bilinmeyenlerin ortaya çıkarılması için arkeometalurji çalışmaları günümüzde daha çok önem kazanmaktadır. Temrenlerde, diğer arkeolojik kazı buluntularında olduğu gibi etrafında bulunan diğer eserlerin varlığına veya katmanlarına göre dönem tespiti yapılmaktadır, ancak yaş tespiti dönemin üretim ve şekillendirme işlemleri hakkında bilgi vermemektedir. Bu anlamda, bu çalışmada Konya Gevale Kalesi bölgesinde bulunan temrenler arkeometalurjik yöntemlerle incelenmiştir. Konya Gevale Kalesi civarında bulunan temrenlerin farklı tipolojiye sahip olduğu ve temrenlerin tipolojisiyle kullanım amacı arasında bir ilişki olduğu gözlemlenmiştir. On üç yıllık kazılar sonrasında bulunan temrenler arasından i) yassı ve ii) dörtgen geometriye sahip iki farklı temren seçilerek analizleri yapılmıştır. Elde edilen kimyasal ve mikroyapısal analizler sonucunda temrenlerin ait olduğu dönemin üretim ve şekillendirme yöntemleri hakkında bilgi sahibi olunmuştur. Temrenlerin yüzey ve mikroyapı incelemelerinde taramalı elektron mikroskobu (SEM) ile elementel analiz spektroskopisi (EDS) ve optik mikroskop kullanılmıştır. Temrenlerin faz yapısı x-ışını kırınım (XRD) yöntemiyle incelenmiştir. Yapılan incelemelerle, o dönemin sahip olduğu teknoloji nedeniyle üretim ve şekillendirme için daha çok yumuşak çelik grubu kullanılmıştır. Aynı zamanda üretim sırasında izabe işlemlerinin yeterli ölçüde yapılamadığını ve bu nedenle çelik içerisinde istenmeyen elementlerin mevcudiyeti de gözlemlenmiştir. Öte yandan temren üretiminde genellikle döküm ve dövme yöntemlerinin kullanıldığı görülmüştür. Temrenler, uzun yıllar boyunca toprak altında kaldığı için bulundukları ortamla etkileşime girerek homojen bir şekilde korozyona uğramıştır. Ancak bulundukları ve maruz kaldıkları ortamda zaman içerisinde meydana gelen değişimler nedeniyle iç katmanlara doğru farklı korozyon ürünleri oluşumu söz konusudur.


  • Open Access

    Understanding Corrosion Morphology of Duplex Stainless Steel Wire in Chloride Electrolyte

    by Cem Örnek, Kemal Davut, Mustafa Kocabaş, Aleyna Bayatlı, Mustafa Ürgen

    The corrosion morphology in grade 2205 duplex stainless steel wire was studied to understand the nature of pitting and the causes of the ferrite phase’s selective corrosion in acidic (pH 3) NaCl solutions at 60 °C. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely arrayed selective cavities developing selectively on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase’s selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.


  • Open Access

    Understanding Corrosion Morphology of Duplex Stainless Steel Wire in Chloride Electrolyte

    by Cem Örnek, Kemal Davut, Mustafa Kocabaş, Aleyna Bayatlı, Mustafa Ürgen

    The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.