ECElif Cicek

Elif Cicek

*This is an algorithmically generated author record based on publicly available information.

Elif Cicek has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigation friction loss of concrete pavement surface with a new method

    by Orhan Karpuz, Muhammet Vefa Akpınar, Hakan Aslan, Muhammet Çelik, Elif Çiçek

    In this study, the effect of abrasion resistance and fineness modulus of the fine aggregates in the concrete mixture was investigated to determine the friction coefficient loss. Nine concrete mixtures samples were obtained by using three different gradations and fine aggregates with three different Los Angeles (LA) wear resistance. A new accelerated polishing test method was conducted in a laboratory. In the new method, unlike other wheel polishing methods, a constant horizontal friction force was formed alongside the vertical pressure of the wheel contact area. The wet friction coefficients of the concrete surfaces were measured by the British Friction Pendulum. Test results showed that the most friction loss occurred in the fine aggregated concrete mixtures obtained from limestone with the lowest wear resistance, while the least loss values were obtained for basalt with high abrasion resistance.

  • Investigation of pedestrian and vehicle level of service regulation for Hacettepe Sıhhiye campus

    by Elif Çiçek, Taha Ozdemir, Oguzcan Kaplan, Taylan Yusel, Mehmet Punar

    Roads and sidewalks of Hacettepe Campus Children's Emergency were investigated in order to determine the congestion in the "emergency zone" in this area and improvement effects to different road quality methods were discussed. Both level of service of roads (LOS) and sidewalks (PLOS) were studied by using different methods as Highway Capacity Manual (HCM), Landis and Australian methods. As the result of study, since the terrain in the region is not suitable for vehicles, the pedestrian path was narrowed to reduce the traffic on the vehicle road and significantly reduce the problem. In addition, the methods used in the PLOS calculation were found to be deficient in terms of applicability. When comparing the different methods AUSTRALIAN method more realistic results as it has more generalizable perspective than others in this study.

  • Open Access

    Relation Between Quality of Transportation and Nano-Scale Air Pollution

    by Elif Cicek, Semra Ide, Cem Küçük, Oğuzhan Yorulmaz, Murat Vedat Yurttaş, Özge Zorlu Kaymak, Dilem Ergün

    This study has two parts as determining traffic LOS and nanoscale analyses on the filters which can collect nanoparticle materials sourced by exhaust waste. Therefore, at first, determination of the traffic behaviour as the level of service (LOS) in Sıhhiye campus of Hacettepe University in Ankara was studied. Then, exhaust gas analysis by using facing masks was conducted for different parameters and these masks were used to collect and analyse exhaust on them. The parameters were determined as vehicle and fuel types, filter masks, sampling distances respect to exhaust source. The measurements and samplings were realized for the vehicles which are public cars and service minibuses which use different fuel types as petrol, eco-diesel and diesel. Additionally, 5 different filter types were used to analyse traffic behaviour as exhaust gas may affect human health. For this reason, different mask types with different specified parameters, which are using as face masks for health and a new type was prepared by Argiope lobata spider silk membrane, were also investigated in relation to the filtered exhaust gases. Measurements were made for three different distances as 30, 60 and 90 cm from exhaust pipe output and with a constant sampling time range of 3 min. Apart from the previously known microscopic and macroscopic analyses on exhaust gases, it was examined whether the exhaust outputs frequently spread nanoparticle waste or not by using SAXS analyses on samples. As a result of the study, relation with traffic conditions with clear transportation can be affirmed. Additionally, the study reported important outcomes, such as a new designed filter mask material, which prevents the nanoparticles waste material, the critical distance from the exhaust sources and the importance of different fuel usage.

  • Investigation of Different Types of Fibers for Roads by CBR Tests

    by Elif Çi̇çek, Volkan Buyukakin

    In this study, California Bearing Ratio (CBR) tests in a laboratory were performed to observe the behaviour of granular layer fills reinforced with discrete fibers. Six different fiber types were used in granular road layer by using different methods. Firstly, fibers were added in the road as a layer, then they mixed with soil particles, and as a third method they mixed with soil by laying a geotextile in the road layer, in other words it was used as combine reinforced model. And as the last method only a geotextile was laid and used in the pavement soil. By using these methods, the influence of different type of reinforcements on CBR and bearing capacity ratio values were investigated. Additionally, effects on the pavement layer thickness were calculated and for the best configuration of fiber reinforced sample a cost analysis was conducted. As a result of the study, CBR test values for each fiber type used in the study have different values, and for small penetration levels some test results show no improvement for bearing capacity ratio of the road. It was noticed that when increasing the penetration level, the bearing capacity ratios have larger values. Thus, cost and layer thickness numbers were various for different reinforced road layer models. Therefore, in the real life road projects before using fiber types, cost and performance analysis should be made to determine the more effective one. Bilindiği gibi, lifler yol üstyapısının tasarımı için iyileştirme malzemelerinden biri olabilir. Ancak farklı tiplerin California Rulman Oranı (CBR) ve kaplama kalınlığı üzerindeki etkileri henüz bilinmemektedir. Bu nedenle, bu çalışmada granüler kaplama tabakasında farklı yöntemlerle altı farklı lif türü kullanılmıştır. Kompozit donatılı modeller için öncelikle kaplama tabakasına lifler katman olarak eklenmiş, daha sonra toprakla karıştırılmış ve son olarak toprakla karıştırılmış ve katman olarak geotekstil eklenmiştir. Bu üç yöntem kullanılarak farklı tipteki donatıların CBR ve taşıma gücü oranı değerlerine etkisi araştırılmıştır. Ek olarak, kaplama tabakası kalınlığı üzerindeki etkiler hesaplanmış ve lif takviyeli numunenin en iyi konfigürasyonu için bir maliyet analizi yapılmıştır. Çalışma sonucunda, farklı liflerin farklı davranışlar gösterebildiği ve küçük penetrasyon seviyeleri için bazılarının CBR değerlerini iyileştiremediği ve artan penetrasyon taşıma kapasite oranları artırıldığı gözlenmiştir. Bu nedenle gerçek projeler için lif donatı kullanmadan önce maliyet ve performans analizi yapılması gerekliliği belirlenmiştir.


  • Sonlu Elemanlar Metodu Kullanarak Farklı Yol Modellerinin Oturmaya Etkisinin İncelenmesi

    by Elif Çi̇çek

    Bu çalışmada, farklı yol tiplerinin oturma davranışı üzerine etkisi sonlu elemanlar yöntemi kullanılarak incelenmiştir. Analizlerde aynı temel ve alt temel tabakaları üstüne inşa edilen farklı yol kaplama cinsleri için analiz modelleri oluşturulmuştur. Maksimum büyüklükleri aynı değerde olan statik ve dinamik yüklerde oluşabilecek oturma değerleri için iki boyutlu hesaplamalar yapılmıştır. Farklı tekerlek aralıkları (15, 30, 60 ve 120cm) için statik ve dinamik yükler altında oluşan asfalt ve beton yol tiplerindeki oturma davranışları incelenmiştir. İlk olarak asfalt yol kaplamasında analizler yürütülmüştür. Daha sonra ise beton yol ve yarısı beton yol olup kaplamanın diğer üst yarısının asfalt kaplama olma durumları için analiz sonuçları karşılaştırılmış ve farklılıklar yorumlanmıştır. Böylece hem tekerlek aralığı, yükleme tipi ve kaplama cinslerinin kara yolunda meydana getirebileceği oturma davranışları nümerik bir çalışma ile değerlendirilmiştir.

  • Open Access

    Farklı Malzemeler ve Geosentetiklerin Yol Dolgusu Güvenliğine ve Davranışına Etkileri

    by Elif Çi̇çek

    Tr en Bu çalışmada, doğal ve atık malzemelerin geri kazanımından elde edilen yeni malzemeler ile oluşturulmuş yol dolgusu modelleri sonlu elemanlar yöntemi kullanılarak analiz edilmiştir. Kumlu silt, kaya agregası, beton, cam gibi farklı malzemelerin yol dolgusuna etkileri incelenmiş ve atık liflerin yol dolgusunda kullanıldığı modellerin analiz sonuçları doğal koşullar ile karşılaştırılmıştır. Ayrıca farklı geosentetik donatı sayıları ile güçlendirilmeye çalışılan yol dolgusu modelleri için de hesaplamalar yapılmıştır. Böylece oluşturulan yol modelinin güvenlik sayısına farklı malzemelerin, liflerin ve geosentetik sayısının etkileri incelenmiştir. Yolun ani göçmesine karşı değerlendirmeler yapılarak, dolgu altındaki yeraltı suyundan kaynaklanacak konsolidasyon davranışının da etkileri farklı malzeme koşulları için karşılaştırılmıştır. Ayrıca, farklı malzemeler kullanılarak inşa edilen dolgularda yolun farklı bölgelerinde trafik yükünden oluşabilecek oturma farkları da değerlendirilmiş ve geosentetiğin etkileri de belirlenmeye çalışılmıştır. Sonuçlar incelendiğinde hem çevreci hem de daha verimli çözümler için değerlendirmeler yapılmıştır. Atık malzemelerin geri dönüşümü ile elde edilen malzemelerin, yol dolgularının stabilite ve güvenlikleri için önemli katkılar sağlayabileceği gözlenmiştir. In this study, road embankment models constructed with new materials obtained from the recycling of natural and waste materials were analysed using the finite element method. The effects of different materials such as sandy silt, rock aggregate, concrete, glass on the road fill were investigated and the results of the analysis of the models using waste fibers in the road fill were compared with the natural conditions. In addition, calculations have been made for road embankment models which are tried to be reinforced with different numbers of geosynthetic reinforcement. Thus, the effects of different materials, fibers and geosynthetics on the number of safety of the road model created were examined. Evaluations were made against the collapse of the road and the effects of the consolidation behaviour arising from groundwater under filling were compared for different material conditions. In addition, the residence differences that may be caused by traffic load in different parts of the road in the fillings constructed using different materials were evaluated and the effects of geosynthetics were tried to be determined. When the results were examined, evaluations were made for both environmental and more efficient solutions. It has been observed that the materials obtained by recycling of waste materials can make significant contributions to the stability and safety of road embankments.

  • Stress Distribution below a Continuous Footing on Geotextile-Reinforced Soil

    by Elif Cicek, Erol Guler, Temel Yetimoglu

    This study investigated the additional vertical stress (Δσ) change occurring under the centerline of a continuous footing on geotextile-reinforced soil. For different reinforcement parameters and conditions, load tests and finite-element model (FEM) analyses were performed. It was determined that the presence of reinforcements reduces the additional vertical stress values. There is a good correlation in some cases between experimental measurements and FEM results, but the values obtained are different from the values proposed based on theoretical considerations developed for uniform materials. Each additional reinforcement layer affects Δσ, and different parameters can affect the values of Δσ. It was determined that the reinforcements create a discontinuity in the triangular failure wedge under the footing, thereby affecting the additional stress developed.


  • Open Access

    Effects of the first reinforcement depth for different types of geosynthetics

    by Elif Cicek, Erol Guler, Temel Yetimoglu

    In this study, the performance of the first reinforcement layer depth for sand subbase of a road or construction was investigated with plate load laboratory tests. Unreinforced and reinforced experiments for different reinforcement types were made by changing the first reinforcement layer depth ratio. One type of geotextile and two different geogrid specimens were used in the research. Load-settlement curves and Bearing Ratios were studied by measuring the results for different settlement ratios. Finally, laboratory measurements of unreinforced and reinforced soil using geotextile reinforcement were compared with Finite Element Model (FEM) analyses modeled under similar conditions. The results demonstrated the effects of different types of reinforcements for different first reinforcement layer locations. The number of reinforcement layers was another parameter which affected the bearing ratio along with the first reinforcement layer depths. It was also observed that the Bearing Ratio (BR) and load-settlement behavior changed significantly with the first reinforcement depth and settlements. Effects on failure modes for unreinforced and reinforced sand soils were compared for each test.