Ahmet Aktürk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahmet Aktürk has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Mustafa Yusuf Yazici
Samsun Üniversitesi
4 shared publications - Melih Yıldız
IĞDIR ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ
3 shared publications - Celal Mert Dikmetaş
Samsun Üniversitesi
1 shared publication Mehmet Emin Arıcı
1 shared publication- Mehmet Emin Arıcı1 shared publication
- Sare Mitincik
SAMSUN ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, MAKİNE MÜHENDİSLİĞİ BÖLÜMÜ
1 shared publication
Latest Publications
- Open Access
- 2 March 2026
- Published by Elsevier in SSRN Electronic Journal
Experimental Evaluation of Thermal and Electrical Performance of Li-Ion Battery Modules Using Expanded Graphite/Paraffin Composites with Varying Bulk Densities
Electro-mobility with Li-ion technology has a great potential to reach the sustainable development goals (SDGs), including affordable and clean energy, sustainable cities and communities. Electro-mobility performance links directly with Li-ion battery performance, and the performance and safety levels of these batteries are primarily a function of operating temperature. Although PCM-graphite based approach offers a valuable solution to regulate the operating temperature, there are limited studies providing experimental data considering realistic operational conditions for battery modules. Therefore, comprehensive experimental investigation is carried out to ensure the thermal and electrical performances of battery module equipped with passive cooling approach of expanded graphite matrix/PCM. Battery modules with 6S4P cell configuration were used in this study. Experiments were carried out using RT-42 PCM for different matrix bulk densities (50 g/L, 75 g/L, and 100 g/L), different ambient temperatures (25°C and 35°C), and different discharge currents (13.4 A and 30 A). The performances of composite battery modules and bare battery module were compared and discussed. For 25 °C and 30 A test, the EG/PCM (100 g/L module showed improvements of 21.4% and 68.8% in maximum operating temperature and maximum temperature difference, respectively, compared to the bare module. In the demanding 35°C and 30 A test, the same composite battery module showed 91%, 91%, and 71% superior performance compared to the bare battery module in terms of operating time, capacity, and energy capacity, respectively. This passive cooling approach mitigates thermal hotspots, reduces safety risks, and offers a lightweight, efficient BTMS solution for EVs.
- 2 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessExperimental Evaluation of Thermal and Electrical Performance of Li-Ion Battery Modules Using Expanded Graphite/Paraffin Composites with Varying Bulk Densities
Electro-mobility with Li-ion technology has a great potential to reach the sustainable development goals (SDGs), including affordable and clean energy, sustainable cities and communities. Electro-mobility performance links directly with Li-ion battery performance, and the performance and safety levels of these batteries are primarily a function of operating temperature. Although PCM-graphite based approach offers a valuable solution to regulate the operating temperature, there are limited studies providing experimental data considering realistic operational conditions for battery modules. Therefore, comprehensive experimental investigation is carried out to ensure the thermal and electrical performances of battery module equipped with passive cooling approach of expanded graphite matrix/PCM. Battery modules with 6S4P cell configuration were used in this study. Experiments were carried out using RT-42 PCM for different matrix bulk densities (50 g/L, 75 g/L, and 100 g/L), different ambient temperatures (25°C and 35°C), and different discharge currents (13.4 A and 30 A). The performances of composite battery modules and bare battery module were compared and discussed. For 25 °C and 30 A test, the EG/PCM (100 g/L module showed improvements of 21.4% and 68.8% in maximum operating temperature and maximum temperature difference, respectively, compared to the bare module. In the demanding 35°C and 30 A test, the same composite battery module showed 91%, 91%, and 71% superior performance compared to the bare battery module in terms of operating time, capacity, and energy capacity, respectively. This passive cooling approach mitigates thermal hotspots, reduces safety risks, and offers a lightweight, efficient BTMS solution for EVs.
- Open Access
- 6 January 2026
- Published by Elsevier in Journal of Engineering Research
- Vol. 14 (2) , 2118-2132
Assessing influencing factors on a passive cooling system for a Li-ion battery cell by employing the RSM methodology
- 6 January 2026
- Published by Elsevier in Journal of Engineering Research
- Vol. 14 (2) , 2118-2132
Open AccessAssessing influencing factors on a passive cooling system for a Li-ion battery cell by employing the RSM methodology
- Open Access
- 1 September 2025
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 22 (3) , 12713-12724
Battery Simulation Using the NTGK Model: Effects of Model Parameters and Implementation under Dynamic Current Profiles
With the growth in electric powertrain vehicles, the demand for batteries is increasing. Therefore, it is crucial to operate the battery system within an optimum range in terms of performance, life, and safety. In this regard, battery thermal management systems have garnered significant attention for their crucial role in maintaining a battery system within predetermined thermal conditions. The current study focuses on battery simulation using the Newman, Tiedemann, Gu, and Kim (NTGK) model, which is widely applied in the literature. However, the accuracy of this model strongly depends on the empirical parameters U and Y, and existing fitting-based methods often lead to limited reliability. Thus, the effects of the parameters on the temperature evolution of a battery cell were investigated by comparing simulation results with manufacturer data at different discharge rates. This study presents a structured solution scheme to determine the U and Y parameters (for DoD < 0.83). The battery model with the calculated parameters was also simulated under a dynamic current profile representing the Worldwide Harmonized Light Vehicle Test Cycle (WLTC), which is used in approval tests of electric vehicles, at different convective heat transfer coefficients. The results show that temperature prediction with the solution scheme is in good agreement with the battery data obtained from its datasheet. The Y parameter in the NTGK model is of great importance for the development of heat generation characteristics, which in turn affects temperature development. The maximum temperature increase under WLTC was found to be 3.08°C at 20 W/m²K and 8.87°C at 5 W/m²K, while the absolute temperature prediction errors remained below 2.67 K. The temperature rise under dynamic load is consistent with the literature, supporting the validity of the proposed solution scheme.
- 1 September 2025
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 22 (3) , 12713-12724
Open AccessBattery Simulation Using the NTGK Model: Effects of Model Parameters and Implementation under Dynamic Current Profiles
With the growth in electric powertrain vehicles, the demand for batteries is increasing. Therefore, it is crucial to operate the battery system within an optimum range in terms of performance, life, and safety. In this regard, battery thermal management systems have garnered significant attention for their crucial role in maintaining a battery system within predetermined thermal conditions. The current study focuses on battery simulation using the Newman, Tiedemann, Gu, and Kim (NTGK) model, which is widely applied in the literature. However, the accuracy of this model strongly depends on the empirical parameters U and Y, and existing fitting-based methods often lead to limited reliability. Thus, the effects of the parameters on the temperature evolution of a battery cell were investigated by comparing simulation results with manufacturer data at different discharge rates. This study presents a structured solution scheme to determine the U and Y parameters (for DoD < 0.83). The battery model with the calculated parameters was also simulated under a dynamic current profile representing the Worldwide Harmonized Light Vehicle Test Cycle (WLTC), which is used in approval tests of electric vehicles, at different convective heat transfer coefficients. The results show that temperature prediction with the solution scheme is in good agreement with the battery data obtained from its datasheet. The Y parameter in the NTGK model is of great importance for the development of heat generation characteristics, which in turn affects temperature development. The maximum temperature increase under WLTC was found to be 3.08°C at 20 W/m²K and 8.87°C at 5 W/m²K, while the absolute temperature prediction errors remained below 2.67 K. The temperature rise under dynamic load is consistent with the literature, supporting the validity of the proposed solution scheme.
- Open Access
- 1 June 2025
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 15 (2) , 658-674
Numerical Modelling of Graphite-Based Composite Thermal Energy Storage Unit: Effect of Numerical Variable
Thermal energy storage (TES) systems have a great potential on the providing balance of energy demand/supply, while also contributing to net-zero emissions, a reduced carbon footprint, and a greener environment. Paraffin phase change materials have emerged as a prominent material for TES applications due to its potentially high energy storage density. However, their application is significantly limited by its low thermal conductivity values. This study introduces a composite structure for thermal energy storage, utilizing paraffin as the latent heat storage material and a graphite matrix to enhance thermal conductivity for solar energy and waste heat applications. The effects of various numerical variables of mushy zone parameter, the pressure-velocity coupling, the pressure discretization scheme, and the boundary condition on the melting performance of a PCM-based thermal energy storage system were investigated within an annular storage medium, extending beyond the literature. Simulations were performed using ANSYS-Fluent, employing the enthalpy-porosity technique. The validation of the study was ensured based on the experimental setup. The primary aim of the study was to identify the numerical variables that yield the most realistic results. It was found that most closely representation of the experimental/real conditions is 105 mushy zone constant, a Coupled algorithm for the pressure-velocity coupling, and PRESTO! for the pressure discretization scheme. However, numerical variable effect was not significantly notable for the paraffin-impregnated graphite matrix storage medium. Results also indicated that graphite constrained the motion of paraffin, resulting in a uniform and homogeneous temperature distribution. It is observed that differences in numerical parameters lead to variations (0.42-16.57%) in energy storage rates, considering melting/charging times and the final temperatures of the TES system.
- 1 June 2025
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 15 (2) , 658-674
Open AccessNumerical Modelling of Graphite-Based Composite Thermal Energy Storage Unit: Effect of Numerical Variable
Thermal energy storage (TES) systems have a great potential on the providing balance of energy demand/supply, while also contributing to net-zero emissions, a reduced carbon footprint, and a greener environment. Paraffin phase change materials have emerged as a prominent material for TES applications due to its potentially high energy storage density. However, their application is significantly limited by its low thermal conductivity values. This study introduces a composite structure for thermal energy storage, utilizing paraffin as the latent heat storage material and a graphite matrix to enhance thermal conductivity for solar energy and waste heat applications. The effects of various numerical variables of mushy zone parameter, the pressure-velocity coupling, the pressure discretization scheme, and the boundary condition on the melting performance of a PCM-based thermal energy storage system were investigated within an annular storage medium, extending beyond the literature. Simulations were performed using ANSYS-Fluent, employing the enthalpy-porosity technique. The validation of the study was ensured based on the experimental setup. The primary aim of the study was to identify the numerical variables that yield the most realistic results. It was found that most closely representation of the experimental/real conditions is 105 mushy zone constant, a Coupled algorithm for the pressure-velocity coupling, and PRESTO! for the pressure discretization scheme. However, numerical variable effect was not significantly notable for the paraffin-impregnated graphite matrix storage medium. Results also indicated that graphite constrained the motion of paraffin, resulting in a uniform and homogeneous temperature distribution. It is observed that differences in numerical parameters lead to variations (0.42-16.57%) in energy storage rates, considering melting/charging times and the final temperatures of the TES system.
- 1 March 2021
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 11 (1) , 535-547
Numerical Investigation on Heat Transfer and Hydraulic Performance of Al2O3-Water Nanofluid as a Function of Reynolds Number and Flow Velocity
This study numerically investigates the heat transfer and hydraulic performance of Al2O3-water nanofluids flowing through a horizontal smooth pipe exposed to a constant heat flux. The nanofluids were regarded as four different varying concentrations in the range from 0.01 to 0.04 by a 0.01 increment (by volume) of the nano-particle, Al2O3. Numerical analyses were performed using the finite volume method to solve governing equations in the created three-dimensional domain. The heat transfer and hydraulic characteristics of the nanofluids were separately investigated as a function of both Re number and flow velocity corresponding to the turbulent flow regime. The results show that the convective heat transfer coefficients increase remarkably with the increase of Al2O3 fraction, and the maximum overall enhancement ratio was found by 1.30, in the case of the same Reynolds number. In contrast, in the case of the same flow velocities to the base fluid, the convective heat transfer coefficients of the nanofluids worsened with relative to the base fluid due to higher viscosity values of the nanofluids which cause a decrease in Reynolds numbers. Moreover, friction factors with nanofluids increased, which gave rise to the overall enhancement ratios to be at lower than 1.0.
- 1 March 2021
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 11 (1) , 535-547
Numerical Investigation on Heat Transfer and Hydraulic Performance of Al2O3-Water Nanofluid as a Function of Reynolds Number and Flow Velocity
This study numerically investigates the heat transfer and hydraulic performance of Al2O3-water nanofluids flowing through a horizontal smooth pipe exposed to a constant heat flux. The nanofluids were regarded as four different varying concentrations in the range from 0.01 to 0.04 by a 0.01 increment (by volume) of the nano-particle, Al2O3. Numerical analyses were performed using the finite volume method to solve governing equations in the created three-dimensional domain. The heat transfer and hydraulic characteristics of the nanofluids were separately investigated as a function of both Re number and flow velocity corresponding to the turbulent flow regime. The results show that the convective heat transfer coefficients increase remarkably with the increase of Al2O3 fraction, and the maximum overall enhancement ratio was found by 1.30, in the case of the same Reynolds number. In contrast, in the case of the same flow velocities to the base fluid, the convective heat transfer coefficients of the nanofluids worsened with relative to the base fluid due to higher viscosity values of the nanofluids which cause a decrease in Reynolds numbers. Moreover, friction factors with nanofluids increased, which gave rise to the overall enhancement ratios to be at lower than 1.0.