MIMehmet Ipekoglu

Mehmet Ipekoglu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Mehmet Ipekoglu has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Natural Pumice-Filled Flexible Polyurethane Composites: Effect of Filler Content on Mechanical Performance and Cyclic Durability

    by Omer Uctu, Mehmet Ipekoglu, Onder Albayrak

    This study investigates the effect of natural pumice filler content on the physical and mechanical performance of flexible polyester-based polyurethane (PU) composites. Composites containing 0, 2, 5, 10, and 20 wt.% pumice were produced using a constant PU matrix formulation and identical processing conditions. Microstructural and structural characteristics were examined using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR), while density, water absorption, tensile behavior, abrasion resistance, and cyclic flexural durability were evaluated. Increasing pumice content resulted in greater local microstructural heterogeneity and increased density and water absorption. Tensile strength exhibited a non-linear numerical response to filler content, with the highest mean value obtained at 5 wt.% pumice, although the differences among formulations were not statistically significant. In contrast, elongation decreased significantly overall with increasing filler content, while mean abrasion mass loss progressively increased with filler loading. Cyclic flexural testing revealed that the unfilled PU and 2 wt.% composite completed 30,000 cycles without measurable crack propagation at 20 and 0 °C, whereas higher filler contents exhibited severe crack growth or complete fracture. At −20 °C, all formulations fractured completely. Overall, pumice content produced a property-dependent response, revealing a trade-off among tensile response, deformability, abrasion resistance, and cyclic durability. These findings provide a basis for tailoring flexible PU composites for applications involving repeated deformation and mechanical contact, including footwear and cushioning components.

  • Open Access

    Structure–Property Relationships in Polyester-Based Polyurethane Foams with Varying Isocyanate Index for Footwear Midsole Applications

    by Onder Albayrak, Mehmet Ipekoglu, Omer Uctu, Gonul S. Batibay, Ahmet Calik, Ana Pilipović

    Polyurethane (PU) foams are widely used in footwear midsoles because their cellular structure, density, impact-attenuation capability, and mechanical durability can be tailored through formulation design. In this study, polyester-based PU foams were prepared at different isocyanate indices while keeping the main formulation components constant, and their structure-property relationships were evaluated under midsole-relevant conditions. The samples were characterized by density, tensile and compression testing, standard abrasion wear testing, water absorption, temperature-dependent flexural resistance, Fourier transform infrared (FTIR), scanning electron microscope (SEM), differential scanning calorimetry (DSC), thermogravimetric analysis/derivative thermogravimetry (TGA/DTG), and dry/wet tribometry. FTIR results confirmed the formation of urethane/urea-related linkages and the absence of detectable residual isocyanate groups, whereas DSC indicated broad heat-flow events typical of segmented PU systems, including high-temperature events that should be interpreted together with TGA. TGA/DTG analysis showed similar initial degradation behavior for all formulations; however, the 138-index sample exhibited the highest t90% value, indicating improved high-temperature mass retention. Tribometric tests revealed an environment-dependent coefficient of friction (COF) response: the 138-index sample exhibited the lowest steady-state COF under dry sliding (μss = 0.211), whereas the 113-index sample showed the lowest COF value under wet sliding conditions (μss = 0.176). Overall, among the three stable formulations investigated, the 113-index formulation exhibited the most balanced multi-property performance. These results suggest that, within the tested formulation range, midsole-relevant PU foam performance is associated with a balance of formulation characteristics rather than simply with increasing the isocyanate index.


  • Open Access

    Development of a generalized ANN-based evaporation heat transfer correlation for refrigerants in turbulent flow

    by Suleyman Sisman, Murathan Durmaz, Mehmet İpEkoglu

    Global warming, primarily caused by the accumulation of greenhouse gases, poses a major threat due to its impact on climate systems. Transitioning to low Global Warming Potential (GWP) refrigerants, such as R1234yf, in cooling systems is crucial to mitigate this. Although numerous evaporation correlations exist in the literature for turbulent flow, each correlation is typically valid only for a specific range of operating conditions (e.g., Reynolds number, Prandtl number, heat flux, saturation temperature). No generalized correlation currently exists that can accurately predict the evaporation heat transfer coefficient of refrigerants across the combined range of conditions covered by these individual correlations. As a novel contribution, present study an ANN-based generalized correlation developed using an aggregated dataset spanning these diverse ranges. The proposed artificial neural network-based correlation achieved high accuracy, with an R $$^2$$ 2 value exceeding 98% and a MAPE of 8.3%, indicating an acceptable prediction error. By covering a wide range of conditions with a single equation, suggested correlation reduces the experimental burden and accelerates the development of low-GWP refrigerant systems.


  • On the multi-scale mechanical and tribological behavior of directed energy deposited inconel-718

    by Huzaifa Asif, M. Farhan Raza, Mehmet Ipekoglu, Guney Guven Yapici

    Inconel-718 superalloy was additive-manufactured via laser direct energy deposition, followed by distinct post-processing thermal treatment conditions. Nanoindentation mapping revealed that samples subjected to double aging exhibited the highest average hardness and elastic modulus, attributed to the precipitation of γ′ and γ″ phases during the double-aging heat treatment. The presence of these precipitates was confirmed, resulting in tensile strength levels exceeding 1350 MPa along with improved wear resistance. However, direct double-aged condition showed lower elongation, attributed to the formation of brittle phases. Wear experiments further demonstrated the effectiveness of thermal processing in enhancing overall mechanical and tribological performance compared with the as-built condition.

  • Open Access

    Türkiye’nin Büyük Şehirlerinde Yaz Aylarında Cam Filmi Kullanımı ile Isı Kazancı Kestirimi ve Maliyet Analizi

    by Erdem Onur Özyurt, Mehmet Gökhan Gökçen, Mehmet İpEkoğlu

    Küresel ısınma ile bağlantılı olarak dünya çapında birçok felaket meydana gelmektedir. Sera gazlarının emisyon seviyelerini azaltmanın yollarını bulmak için birçok çalışma yürütülmektedir. Fosil yakıt tüketiminin azaltılması emisyonları azaltmak için kullanılan en yaygın yöntemdir. Bu çalışmada belirli cam filmi özelliklerine sahip bir model binada sağlanacak ısı kazancının kestirimi gerçekleştirilmiştir. Sonuçlar, saydam ve renkli cam üzerine kaplanmış üç film tipi için karşılaştırmalı olarak verilmiştir. Isı kazancı kestirimi, şehir, cam, bina ve nem özellikleri dikkate alınarak yaz günleri için uyarlamalı olarak yapılmıştır. Filmsiz saydam cam için elde edilen son oda sıcaklığı referans olarak alınmış ve diğer yedi tipte cam için kestirim bu referansa göre yapılmıştır. Örnek binanın konumu, sıcaklığı ve cephesi gibi özellikler dikkate alınarak elektrik tüketimi, karbon emisyonu ve fiyat açısından maliyet analizi yapılmıştır.

  • COOLING PERFORMANCE PREDICTION OF A METAL FOAM INTERNAL HEAT EXCHANGER: AN ARTIFICIAL NEURAL NETWORK APPROACH

    by Suleyman Sisman, Mehmet Ipekoglu, Ismail Cem Parmaksizoglu

    Although HFC refrigerants have high global warming potential (GWP) values, they are preferred due to their satisfactory cooling performance and A1 fire protection classification. If possible, alternatives of HFC-type refrigerants should be used; if not, they should be used with the least charge value. In this study, the effect of metal foam heat exchanger was investigated to reduce the amount of refrigerant in the refrigeration system. The performance of the metal foam incorporated internal heat exchanger (IHX) was estimated by trained artificial neural networks (ANNs) using the correlations given in the literature, and the results were compared with the experimental data presented in the literature. For the same cooling capacity, a higher performance is achieved by using IHX with metal foam additives. Although the developed correlation has been extracted for IHX, it could be applied for all HE with gas flow.


  • Open Access

    Production and mechanical characterization of polyethylene matrix composites with the addition of linen and cotton waste fabric filler materials

    by Mehmet İpEkoğlu, Hasan Gündüz, Önder Albayrak

    In this study, linen and cotton fibers obtained from fabric waste were used as filler materials and polyethylene was used as matrix material to produce fiber reinforced polymer composites using injection molding. Use of fabric waste as filler material enables utilization of linen and cotton wastes while decreasing the amount of polyethylene used in the composites resulting in an environmentally friendly material. Prepared samples with varying content of linen and cotton wastes (5, 10 and 20 vol. %) were compared with each other and with polyethylene samples without any filler, based on their yield, tensile and fracture strengths, percent elongation and hardness values. Samples were also evaluated for their chip formation characteristics based on chip lengths at various machining speeds and examined for their visual appearance. Results indicated that linen waste fibers can be used to improve the strength of polyethylene based composites while cotton waste fibers can be utilized to enhance the elongation characteristics of the samples.


  • Open Access

    Morphological, microstructural and photocatalytic characterization of undoped and Ni, Co doped Fe2O3 particles synthesized by sonochemical method

    by Eli̇f Emi̇l Kaya, Burak Evren, Zeynep Erdöl, Duygu Eki̇nCi̇, Mehmet İpEkoğlu, Si̇bEl Özenler

    In this study, an abundant and eco-friendly photocatalytic material, Fe2O3 particles were synthesized by sonochemical method. Morphological and microstructural investigations of synthesized undoped and Ni, Co-doped Fe2O3 particles were performed. The effect of particle morphology and microstructure on its photocatalytic performance was further investigated. Comparative studies for evaluating particle crystallite sizes were conducted by Williamson-Hall (W-H) method and modified Debye-Scherrer (MDS). Crystallite sizes and lattice strains of Fe2O3 induced by process parameters were calculated by W-H method based on uniform deformation model (UDM). The crystallite sizes of the synthesized powders were calculated in the range of 200 nm and 76 nm by Williamson-Hall analysis. In addition to structural investigation, dislocation density of the synthesized particles was calculated by Williamson-Smallman relation. Afterwards, photocatalytic performance of Fe2O3 particles was investigated in detail. The photodegradation of methylene blue solutions in the presence of light in 20 min with samples 3,4, and 5 in 20 min were 0.937, 0.896, and 0.855, respectively. Moreover, the photodegradation of methylene blue solution with sample 5 for 15, 30, and 45 min were 0.9, 0.828, and 0.757, respectively. A photocatalytic activity of 24.25% has been observed under optimum conditions for the time interval of 45 min.


  • Effect of Coating Method on the Surface Characteristics of NiTi Shape Memory Alloy

    by Gorkem Muttalip Simsek, Mehmet Ipekoglu, Guney Guven Yapici

    Metallic materials including stainless steel, cobalt-chromium alloys, titanium and its alloys, and nickel-titanium (NiTi) shape memory alloys have been used in biomedical applications since the 1940s due to their favorable mechanical properties. Classified as a smart material, NiTi alloy has gained noticeable popularity in biomedical fields such as orthopedic, dental, and cardiovascular applications as it retains reasonable corrosion resistance and biocompatibility along with unique shape memory properties. However, several studies have shown their limits in medical applications due to the risk of Ni ions release from the NiTi implant surface. In order to prevent Ni release, ceramic-based surface coatings such as hydroxyapatite, alumina, and titanium dioxide have been proposed applied by various methods such as electrophoretic deposition, sol-gel, biomimetic and dip coating. In this work, HA coatings on NiTi wire samples were obtained by using biomimetic and dip-coating methods. The biomimetic coating consisted of immersing the NiTi wire samples into simulated body fluid for 24 and 48 h periods, whereas dip coating was accomplished by placing the NiTi wire samples into the HA suspension and retracting the sample with a controlled speed. The effects of the two coating methods on coating quality, surface characteristics and corrosion behavior of NiTi wire samples were investigated. Dip coating method was shown to be a more favorable technique for the NiTi wire samples used throughout this study.


  • Comparison of deep drawability of AA5754-H22 and AA6061-T6 aluminum alloys for automotive applications

    by Mehmet Ipekoglu, Onur Erbas, Hamad Ul Hassan

    Being one of the most commonly applied sheet metal forming processes in automotive industry, deep drawing technologies are challenged by the concerns of global warming for higher fuel economy requirements in the recent years. To reduce the weight of the vehicles in order to obtain fuel economy, lighter and safer materials are used in automotive industry. Aluminum alloys, due to their low density compared to steels, are an important group of materials, in particular for lightweight construction of vehicles. In this study, two different aluminum alloys, namely AA5754-H22 and AA6061-T6, are evaluated for their potential use in nonload bearing applications in commercial vehicles by comparing their deep drawability characteristics. For this purpose, they are characterized by uniaxial tensile and Nakajima tests. In the next step, the deep drawing experiments are performed under different levels of blankholder force. The distance of the cup center to the edge of the die is also evaluated to investigate ... Kurzfassung Als einer der am häufigsten angewandten Metallblechumformprozesse im Fahrzeugbau bestehen bei den Tiefziehtechniken Herausforderungen bezüglich des Klimawandels in Bezug auf höhere Treibstoffwirtschaftlichkeitsanforderungen in den letzten Jahren. Um das Gewicht der Fahrzeuge für eine bessere Treibstoffwirtschaftlichkeit zu reduzieren, werden leichtere und sichere Werkstoffe in der Automobilindustrie verwendet. Aufgrund ihrer geringeren Dichte im Vergleich zu Stählen stellen Aluminiumlegierungen eine wichtige Werkstoffgruppe dar, insbesondere für den Fahrzeugleichtbau. In der diesem Beitrag zugrunde liegenden Studie wurden zwei verschiedene Aluminiumlegierungen, und zwar AA5754-H22 und AA6061-T6, bezüglich ihres potentiellen Gebrauchs für nicht lasttragende Anwendungen in kommerziellen Fahrzeugen evaluiert, indem ihre Tiefzieheigenschaften verglichen wurden. Zu diesem Zweck wurden sie mittels einachsiger Zugversuche und sogenannter Nakajima-Tests charakterisiert. Im nächsten Schritt wurden die ...