Prakash Vinod
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Prakash Vinod has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- M. A. Manjunath
Central Manufacturing Technology Institute, Bengaluru, Karnataka, India
3 shared publications - Tadigotla Narendra Reddy
Central Manufacturing Technology Institute, Bengaluru, Karnataka, India
3 shared publications - M. Girish Kumar
Central Manufacturing Technology Institute, Bengaluru, Karnataka, India
2 shared publications - Mervin A. Herbert
National Institute of Technology Karnataka (NITK), Surathkal, Karnataka, India
2 shared publications - Shrikantha Sasihithlu Rao
Department of Mechanical Engineering, National Institute of Technology, Surathkal, India
2 shared publications - A. Palaniappan
Central Manufacturing Technology Institute, Bengaluru, Karnataka, India
1 shared publication
Latest Publications
- Open Access
- 1 May 2025
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 24 (5-6) , 9-14
ROS-based 2D LiDAR SLAM for development of autonomous mobile robot
This research paper presents the development of an autonomous mobile robot (AMR), utilizing a Raspberry Pi integrated with the Robot Operating System (ROS) and a 2D LiDAR sensor for Simultaneous Localization and Mapping (SLAM). The primary objective of this work is to demonstrate the feasibility of creating an AMR that can effectively map its surroundings and pave the way for future enhancements in autonomous navigation. The research details the successful implementation of ROS tools, including Cartographer and Hector SLAM, to accurately map the robot’s environment. Building upon this foundation, the paper outlines the planned expansion of the robot’s capabilities through the integration of additional sensors, such as an IMU, to enable self-navigation and advanced autonomous functionalities.
- 1 May 2025
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 24 (5-6) , 9-14
Open AccessROS-based 2D LiDAR SLAM for development of autonomous mobile robot
This research paper presents the development of an autonomous mobile robot (AMR), utilizing a Raspberry Pi integrated with the Robot Operating System (ROS) and a 2D LiDAR sensor for Simultaneous Localization and Mapping (SLAM). The primary objective of this work is to demonstrate the feasibility of creating an AMR that can effectively map its surroundings and pave the way for future enhancements in autonomous navigation. The research details the successful implementation of ROS tools, including Cartographer and Hector SLAM, to accurately map the robot’s environment. Building upon this foundation, the paper outlines the planned expansion of the robot’s capabilities through the integration of additional sensors, such as an IMU, to enable self-navigation and advanced autonomous functionalities.
- Open Access
- 1 November 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (11-12) , 1-9
Improvement of surface finish at bore and face of cylindrical bush through innovative fixtures using abrasive flow finishing
In many manufacturing processes, it is crucial to improve surface finish, especially when producing components with tight tolerances and high aesthetic quality, for specific functional performance. Manual assisted polishing methods are limited in their ability to achieve accuracy, reputability, and reach inaccessible areas of a complex part. An effective finishing method can be standardized through the automation process for improving surface roughness. Irrespective of complex geometries surface finish is achievable through abrasive flow finishing (AFF). The current work experimentally investigates on improving the surface roughness of the cylindrical bush at the location of bore and face through AFF. The cast iron materials of bush elements are finished at the required surfaces using innovative AFFM fixture design. The simultaneous finishing of multiple numbers of dies are evaluated by considering various process parameters of the abrasive flow finishing process. The comparative study of surface roughness before and after the abrasive flow finishing has been analyzed.
- 1 November 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (11-12) , 1-9
Open AccessImprovement of surface finish at bore and face of cylindrical bush through innovative fixtures using abrasive flow finishing
In many manufacturing processes, it is crucial to improve surface finish, especially when producing components with tight tolerances and high aesthetic quality, for specific functional performance. Manual assisted polishing methods are limited in their ability to achieve accuracy, reputability, and reach inaccessible areas of a complex part. An effective finishing method can be standardized through the automation process for improving surface roughness. Irrespective of complex geometries surface finish is achievable through abrasive flow finishing (AFF). The current work experimentally investigates on improving the surface roughness of the cylindrical bush at the location of bore and face through AFF. The cast iron materials of bush elements are finished at the required surfaces using innovative AFFM fixture design. The simultaneous finishing of multiple numbers of dies are evaluated by considering various process parameters of the abrasive flow finishing process. The comparative study of surface roughness before and after the abrasive flow finishing has been analyzed.
- Open Access
- 1 September 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (9-10) , 10-19
A review on variant of visco-elastic polymer media for abrasive flow finishing
Abrasive Flow Finishing (AFF) is a specialized surface finishing method used in a variety of applications, notably for components with complicated geometries and difficult-to-access locations. The improvement of surface finish can lead to enhanced functionality, reliability, and customer satisfaction across various sectors. Wide industrial sectors are associated with AFF like aerospace, automotive, medical, die and mold manufacturing etc. A specifically developed viscoelastic polymer material mixed with abrasive particles forms the basis of AFF. This substance can flow while still applying pressure because of its thick, paste-like consistency. Various carrying mediums are utilized and some require customized media properties, each tailored to unique application requirements. In the process, selecting the right carrying media is crucial to in attaining the best possible surface finish and performance since it affects material removal rates, surface quality, and overall efficiency. The current review paper provides a comprehensive evaluation of the various media options for AFF applications.
- 1 September 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (9-10) , 10-19
Open AccessA review on variant of visco-elastic polymer media for abrasive flow finishing
Abrasive Flow Finishing (AFF) is a specialized surface finishing method used in a variety of applications, notably for components with complicated geometries and difficult-to-access locations. The improvement of surface finish can lead to enhanced functionality, reliability, and customer satisfaction across various sectors. Wide industrial sectors are associated with AFF like aerospace, automotive, medical, die and mold manufacturing etc. A specifically developed viscoelastic polymer material mixed with abrasive particles forms the basis of AFF. This substance can flow while still applying pressure because of its thick, paste-like consistency. Various carrying mediums are utilized and some require customized media properties, each tailored to unique application requirements. In the process, selecting the right carrying media is crucial to in attaining the best possible surface finish and performance since it affects material removal rates, surface quality, and overall efficiency. The current review paper provides a comprehensive evaluation of the various media options for AFF applications.
- Open Access
- 1 July 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (7-8) , 9-13
Minimizing wax shrinkage in investment casting: a novel design for paste-form wax injection
Investment casting refers to an industrial manufacturing process that involves dipping wax patterns into the slurry of refractory material to form a ceramic, plaster, or plastic shell. The wax pattern is further melted, and metal is poured into the shell to create a casting. This process is commonly used to manufacture complexshaped components that require tighter tolerances with a better surface finish. The quality of the final cast component mainly depends on the quality of the wax pattern and ceramic shell. The Quality of wax patterns produced mainly depends on the linear shrinkage, surface roughness, and hardness, so there is a need to remove these defects to improve the quality of the wax patterns and, in turn, the casted product. Among the challenges mentioned above, wax shrinkage plays a crucial role in producing precise components; wax shrinkage can be reduced if injected at a lower temperature or in its paste form, i.e., around 45°- 49°c. To address this shrinkage, a wax injection unit is designed and tested, capable of injecting wax at lower temperatures. The developed subsystem can be integrated with a wax injection moulding machine and can inject wax in its paste form.
- 1 July 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (7-8) , 9-13
Open AccessMinimizing wax shrinkage in investment casting: a novel design for paste-form wax injection
Investment casting refers to an industrial manufacturing process that involves dipping wax patterns into the slurry of refractory material to form a ceramic, plaster, or plastic shell. The wax pattern is further melted, and metal is poured into the shell to create a casting. This process is commonly used to manufacture complexshaped components that require tighter tolerances with a better surface finish. The quality of the final cast component mainly depends on the quality of the wax pattern and ceramic shell. The Quality of wax patterns produced mainly depends on the linear shrinkage, surface roughness, and hardness, so there is a need to remove these defects to improve the quality of the wax patterns and, in turn, the casted product. Among the challenges mentioned above, wax shrinkage plays a crucial role in producing precise components; wax shrinkage can be reduced if injected at a lower temperature or in its paste form, i.e., around 45°- 49°c. To address this shrinkage, a wax injection unit is designed and tested, capable of injecting wax at lower temperatures. The developed subsystem can be integrated with a wax injection moulding machine and can inject wax in its paste form.
- Open Access
- 1 July 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (7-8) , 14-18
Additively manufactured AlSi10Mg alloy metal mirror using single point diamond turning process
The production of blanks and lattice-based support structures for mirrors with intricate geometries can be significantly achieved by metal additive manufacturing (AM) technology. The most commonly used lightweight material for additive manufacturing is AlSi10Mg. A cylindrical sample of 50 mm diameter and a 7 mm thick sample were made using laser powder bed fusion (LPBF) technology. In this study, we used a diamond turning machine (DTM) (Model: IUPTM, Make: CMTI) and achieved surface roughness in the order of ~15 nm, measurement was carried out using Talysurf contact type roughness tester and a confocal 3D microscope. This study could boost the ability to manufacture and make lightweight space optical mirrors.
- 1 July 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (7-8) , 14-18
Open AccessAdditively manufactured AlSi10Mg alloy metal mirror using single point diamond turning process
The production of blanks and lattice-based support structures for mirrors with intricate geometries can be significantly achieved by metal additive manufacturing (AM) technology. The most commonly used lightweight material for additive manufacturing is AlSi10Mg. A cylindrical sample of 50 mm diameter and a 7 mm thick sample were made using laser powder bed fusion (LPBF) technology. In this study, we used a diamond turning machine (DTM) (Model: IUPTM, Make: CMTI) and achieved surface roughness in the order of ~15 nm, measurement was carried out using Talysurf contact type roughness tester and a confocal 3D microscope. This study could boost the ability to manufacture and make lightweight space optical mirrors.
- Open Access
- 1 May 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (5-6) , 1-7
Preliminary investigation on the development of low-cost vibration based condition monitoring DAQ system in industry 4.0
This paper presents a preliminary investigation into the development of a low-cost, vibration-based data acquisition (DAQ) system for condition monitoring in the context of Industry 4.0. The system utilizes a single-axis MEMS accelerometer with a sensitivity of 40 mV/g and a frequency response range of DC to 11 kHz (3 dB) to capture vibration data. This data is processed in real-time at the edge using an ST microcontroller to compute the FFT spectrum. The accuracy of the preliminary vibration data was validated against a reference setup comprising a vibration exciter and an OROS vibration analyzer. When the prototype DAQ module, equipped with the MEMS sensor, was tested on a three-phase induction motor alongside a reference piezoelectric accelerometer, the computed FFT spectra from both setups demonstrated strong similarity. Beyond conventional analysis, the raw data from the DAQ system is integrated into a live dashboard for real-time signal interpretation. Further optimization of this low-cost DAQ system aims to address the condition monitoring needs of micro, small, and medium enterprises (MSMEs), enabling in-situ asset monitoring at an affordable price point.
- 1 May 2024
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 23 (5-6) , 1-7
Open AccessPreliminary investigation on the development of low-cost vibration based condition monitoring DAQ system in industry 4.0
This paper presents a preliminary investigation into the development of a low-cost, vibration-based data acquisition (DAQ) system for condition monitoring in the context of Industry 4.0. The system utilizes a single-axis MEMS accelerometer with a sensitivity of 40 mV/g and a frequency response range of DC to 11 kHz (3 dB) to capture vibration data. This data is processed in real-time at the edge using an ST microcontroller to compute the FFT spectrum. The accuracy of the preliminary vibration data was validated against a reference setup comprising a vibration exciter and an OROS vibration analyzer. When the prototype DAQ module, equipped with the MEMS sensor, was tested on a three-phase induction motor alongside a reference piezoelectric accelerometer, the computed FFT spectra from both setups demonstrated strong similarity. Beyond conventional analysis, the raw data from the DAQ system is integrated into a live dashboard for real-time signal interpretation. Further optimization of this low-cost DAQ system aims to address the condition monitoring needs of micro, small, and medium enterprises (MSMEs), enabling in-situ asset monitoring at an affordable price point.
- Open Access
- 1 December 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (11-12) , 1-19
Interoperable data retrieval solutions for smart manufacturing applications
Industry 4.0 / Digital Transformation technologies benefit industries by enhancing productivity, quality improvements, ease of maintenance and flexibility in manufacturing operations. One major challenge in digitalisation projects is acquiring data from industrial machinery and equipment due to proprietary industrial protocols. Integrating the “Industrial Internet of Things (IIoT)” has spurred digitalisation in manufacturing, enhancing productivity and reliability while lowering labour costs. IIoT links industrial machinery like PLCs, CNCs, and robots via a robust network, generating crucial data for automation. However, due to cost constraints, acquiring data from legacy machines, which use diverse communication protocols, poses a significant challenge, particularly for MSMEs. This paper explores leveraging open-source frameworks for real-time data acquisition from industrial machines in Industry 4.0. Through several test cases, the paper demonstrates the feasibility and benefits of using open-source solutions over vendor-specific licensed software. Additionally, it validates “Wireshark” as a versatile open-source tool for data acquisition across various vendor-specific machines, utilising standard communication protocols. This research offers a pioneering approach to digitalising MSME manufacturing industries while minimising costs efficiently.
- 1 December 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (11-12) , 1-19
Open AccessInteroperable data retrieval solutions for smart manufacturing applications
Industry 4.0 / Digital Transformation technologies benefit industries by enhancing productivity, quality improvements, ease of maintenance and flexibility in manufacturing operations. One major challenge in digitalisation projects is acquiring data from industrial machinery and equipment due to proprietary industrial protocols. Integrating the “Industrial Internet of Things (IIoT)” has spurred digitalisation in manufacturing, enhancing productivity and reliability while lowering labour costs. IIoT links industrial machinery like PLCs, CNCs, and robots via a robust network, generating crucial data for automation. However, due to cost constraints, acquiring data from legacy machines, which use diverse communication protocols, poses a significant challenge, particularly for MSMEs. This paper explores leveraging open-source frameworks for real-time data acquisition from industrial machines in Industry 4.0. Through several test cases, the paper demonstrates the feasibility and benefits of using open-source solutions over vendor-specific licensed software. Additionally, it validates “Wireshark” as a versatile open-source tool for data acquisition across various vendor-specific machines, utilising standard communication protocols. This research offers a pioneering approach to digitalising MSME manufacturing industries while minimising costs efficiently.
- 17 May 2023
- Published by Springer Nature
- p. 137-147
Finishing of Laser Powder Bed Fusion-Based Turbine Blade Sample Using Polymer Rheological Abrasive Fluids
- 17 May 2023
- Published by Springer Nature
- p. 137-147
Finishing of Laser Powder Bed Fusion-Based Turbine Blade Sample Using Polymer Rheological Abrasive Fluids