Valentin Breton
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Valentin Breton has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Francois Costa
SATIE Laboratory Universit Paris Est Crteil, ENS Paris-Saclay, CNRS, Universit Paris-Saclay, Gif sur Yvette, France
2 shared publications - Ghislain Despesse
CEA-LETI, Grenoble, France
2 shared publications - Alexandre Reinhardt
Université Grenoble Alpes, CEA-Leti, Grenoble, France
1 shared publication - Emile Bigot
DRT, CEA-Leti, Grenoble, France
1 shared publication Emma Borel
CEA-Leti, Univ. Grenoble Alpes, Grenoble, France
1 shared publicationKomi-Ferdinand Gneza
CEA-Leti, Univ. Grenoble Alpes, Grenoble, France
1 shared publication
Latest Publications
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (8) , 10012-10025
A New Isolated Topology of DC–DC Converter Based on Piezoelectric Resonators
This article presents a new isolated topology of dc–dc converter based on piezoelectric resonators. Contrary to most existing topologies, the proposed one uses the natural isolation of piezoelectric resonators to isolate the converter's output from the input and vice-versa. Considering the resonators’ constraints, our study focuses on the most efficient isolated conversion cycle with zero-voltage switching (ZVS) operations. The case studied is a highly efficient step-down isolated dc–dc converter with a gain ranging from 0 to 1 and an input voltage up to 360 V. The converter uses two piezoelectric resonators working in series. The conversion principle is validated thanks to a prototype operating at a frequency around 95 kHz. Experimental measurements are made on a wide range of input voltage from 12 to 360 V with a conversion ratio of 0.0165 to 0.95. The output power reaches either 179.1 W with an 89% efficiency at 360 V input voltage and 346 V output voltage, or 4.5 W with a 97.2% peak efficiency for a 48 to 45.8 V conversion, using a 25 mm piezoelectric disc with a thickness of 2 and 1 mm, respectively. An efficiency higher than 80% is measured over a wide range of operating points.
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (8) , 10012-10025
A New Isolated Topology of DC–DC Converter Based on Piezoelectric Resonators
This article presents a new isolated topology of dc–dc converter based on piezoelectric resonators. Contrary to most existing topologies, the proposed one uses the natural isolation of piezoelectric resonators to isolate the converter's output from the input and vice-versa. Considering the resonators’ constraints, our study focuses on the most efficient isolated conversion cycle with zero-voltage switching (ZVS) operations. The case studied is a highly efficient step-down isolated dc–dc converter with a gain ranging from 0 to 1 and an input voltage up to 360 V. The converter uses two piezoelectric resonators working in series. The conversion principle is validated thanks to a prototype operating at a frequency around 95 kHz. Experimental measurements are made on a wide range of input voltage from 12 to 360 V with a conversion ratio of 0.0165 to 0.95. The output power reaches either 179.1 W with an 89% efficiency at 360 V input voltage and 346 V output voltage, or 4.5 W with a 97.2% peak efficiency for a 48 to 45.8 V conversion, using a 25 mm piezoelectric disc with a thickness of 2 and 1 mm, respectively. An efficiency higher than 80% is measured over a wide range of operating points.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Piezoelectric Materials for the DC-DC Converters Based on Piezoelectric Resonators
This paper presents a generic representation of the six switching sequences of the dc-dc converters based on piezoelectric resonators. In addition, the estimation of current density and voltage limitations of lead zirconate titanate and lithium niobate resonators are given. A comparison between these piezoelectric materials is carried out. Then, we propose a lithium niobate-based piezoelectric resonator design that reduces spurious modes, while providing a quality factor of 3700 and an electromechanical coupling factor k t 2 of 25.5 %. Experimental results demonstrate the operating principle for input-output voltage of 60-20 V around 6 MHz for a wide power range 2-32 W. A peak efficiency of 93.6 % is obtained at 16 W. A power density of 128 W/cm 3 for the designed resonator is reached for input-output voltage of 60-20 V.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Piezoelectric Materials for the DC-DC Converters Based on Piezoelectric Resonators
This paper presents a generic representation of the six switching sequences of the dc-dc converters based on piezoelectric resonators. In addition, the estimation of current density and voltage limitations of lead zirconate titanate and lithium niobate resonators are given. A comparison between these piezoelectric materials is carried out. Then, we propose a lithium niobate-based piezoelectric resonator design that reduces spurious modes, while providing a quality factor of 3700 and an electromechanical coupling factor k t 2 of 25.5 %. Experimental results demonstrate the operating principle for input-output voltage of 60-20 V around 6 MHz for a wide power range 2-32 W. A peak efficiency of 93.6 % is obtained at 16 W. A power density of 128 W/cm 3 for the designed resonator is reached for input-output voltage of 60-20 V.