Chin Keong Ho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Chin Keong Ho has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Rui Zhang
Department of Electrical and Computer Engineering, National University of Singapore, Cluny Road, Singapore
8 shared publications Gang Yang
School of Electrical and Electronic Engineering Nanyang Technological University Singapore
3 shared publicationsYong Liang Guan
School of Electrical and Electronic Engineering Nanyang Technological University Singapore
3 shared publications- Ashish Pandharipande
Philips Research, Eindhoven, The Netherlands
2 shared publications - Lawrence Ong
The University of Newcastle
2 shared publications Suzhi Bi
2 shared publications
Latest Publications
- Open Access
Wireless Energy Beamforming Using Signal Strength Feedback
Multiple antenna techniques, that allow energy beamforming, have been looked upon as a possible candidate for increasing the efficiency of the transfer process between the energy transmitter (ET) and the energy receiver (ER) in wireless energy transfer. This paper introduces a novel scheme that facilitates energy beamforming by utilizing Received Signal Strength Indicator (RSSI) values to estimate the channel. Firstly, in the training stage, the ET will transmit sequentially using each beamforming vector in a codebook, which is pre-defined using a Cramer-Rao lower bound analysis. The RSSI value corresponding to each beamforming vector is fed back to the ET, and these values are used to estimate the channel through a maximum likelihood analysis. The results that are obtained are remarkably simple, requires minimal processing, and can be easily implemented. Also, the results are general and hold for all well known fading models. The paper also validates the analytical results numerically, as well as experimentally, and it is shown that the proposed method achieves impressive results in wireless energy transfer.
Open AccessWireless Energy Beamforming Using Signal Strength Feedback
Multiple antenna techniques, that allow energy beamforming, have been looked upon as a possible candidate for increasing the efficiency of the transfer process between the energy transmitter (ET) and the energy receiver (ER) in wireless energy transfer. This paper introduces a novel scheme that facilitates energy beamforming by utilizing Received Signal Strength Indicator (RSSI) values to estimate the channel. Firstly, in the training stage, the ET will transmit sequentially using each beamforming vector in a codebook, which is pre-defined using a Cramer-Rao lower bound analysis. The RSSI value corresponding to each beamforming vector is fed back to the ET, and these values are used to estimate the channel through a maximum likelihood analysis. The results that are obtained are remarkably simple, requires minimal processing, and can be easily implemented. Also, the results are general and hold for all well known fading models. The paper also validates the analytical results numerically, as well as experimentally, and it is shown that the proposed method achieves impressive results in wireless energy transfer.
- Open Access
Wireless Energy Beamforming using Received Signal Strength Indicator Feedback
Multiple antenna techniques that allow energy beamforming have been looked upon as a possible candidate for increasing the transfer efficiency between the energy transmitter (ET) and the energy receiver (ER) in wireless power transfer. This paper introduces a novel scheme that facilitates energy beamforming by utilizing Received Signal Strength Indicator (RSSI) values to estimate the channel. Firstly, in the training stage, the ET will transmit using each beamforming vector in a codebook, which is pre-defined using a Cramer-Rao lower bound analysis. RSSI value corresponding to each beamforming vector is fed back to the ET, and these values are used to estimate the channel through a maximum likelihood analysis. The results that are obtained are remarkably simple, requires minimal processing, and can be easily implemented. The paper also validates the analytical results numerically, as well as experimentally, and it is shown that the proposed method achieves impressive results.
Open AccessWireless Energy Beamforming using Received Signal Strength Indicator Feedback
Multiple antenna techniques that allow energy beamforming have been looked upon as a possible candidate for increasing the transfer efficiency between the energy transmitter (ET) and the energy receiver (ER) in wireless power transfer. This paper introduces a novel scheme that facilitates energy beamforming by utilizing Received Signal Strength Indicator (RSSI) values to estimate the channel. Firstly, in the training stage, the ET will transmit using each beamforming vector in a codebook, which is pre-defined using a Cramer-Rao lower bound analysis. RSSI value corresponding to each beamforming vector is fed back to the ET, and these values are used to estimate the channel through a maximum likelihood analysis. The results that are obtained are remarkably simple, requires minimal processing, and can be easily implemented. The paper also validates the analytical results numerically, as well as experimentally, and it is shown that the proposed method achieves impressive results.
- Open Access
Wireless Power Meets Energy Harvesting: A Joint Energy Allocation Approach in OFDM-based System
This paper investigates an orthogonal frequency division multiplexing (OFDM)-based wireless powered communication system, where one user harvests energy from an energy access point (EAP) to power its information transmission to a data access point (DAP). The channels from the EAP to the user, i.e., the wireless energy transfer (WET) link, and from the user to the DAP, i.e., the wireless information transfer (WIT) link, vary over both time slots and sub-channels (SCs) in general. To avoid interference at DAP, WET and WIT are scheduled over orthogonal SCs at any slot. Our objective is to maximize the achievable rate at the DAP by jointly optimizing the SC allocation over time and the power allocation over time and SCs for both WET and WIT links. Assuming availability of full channel state information (CSI), the structural results for the optimal SC/power allocation are obtained and an offline algorithm is proposed to solve the problem. Furthermore, we propose a low-complexity online algorithm when causal CSI is available.
Open AccessWireless Power Meets Energy Harvesting: A Joint Energy Allocation Approach in OFDM-based System
This paper investigates an orthogonal frequency division multiplexing (OFDM)-based wireless powered communication system, where one user harvests energy from an energy access point (EAP) to power its information transmission to a data access point (DAP). The channels from the EAP to the user, i.e., the wireless energy transfer (WET) link, and from the user to the DAP, i.e., the wireless information transfer (WIT) link, vary over both time slots and sub-channels (SCs) in general. To avoid interference at DAP, WET and WIT are scheduled over orthogonal SCs at any slot. Our objective is to maximize the achievable rate at the DAP by jointly optimizing the SC allocation over time and the power allocation over time and SCs for both WET and WIT links. Assuming availability of full channel state information (CSI), the structural results for the optimal SC/power allocation are obtained and an offline algorithm is proposed to solve the problem. Furthermore, we propose a low-complexity online algorithm when causal CSI is available.
- 24 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 14 (11) , 6150-6163
Optimal Cell Clustering and Activation for Energy Saving in Load-Coupled Wireless Networks
Optimizing activation and deactivation of base station transmissions provides an instrument for improving energy efficiency in cellular networks. In this paper, we study the problem of performing cell clustering and setting the activation time of each cluster, with the objective of minimizing the sum energy, subject to a time constraint of serving the users' traffic demand. Our optimization framework accounts for inter-cell interference, and, thus, the users' achievable rates depend on cluster formation. We provide mathematical formulations and analysis, and prove the problem's NP hardness. For problem solution, we first apply an optimization method that successively augments the set of variables under consideration, with the capability of approaching global optimum. Then, we derive a second solution algorithm to deal with the trade-off between optimality and the combinatorial nature of cluster formation. Numerical results demonstrate that our solutions achieve more than 40% energy saving over existing schemes, and that the solutions we obtain are within a few percent of deviation from global optimum.
- 24 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 14 (11) , 6150-6163
Optimal Cell Clustering and Activation for Energy Saving in Load-Coupled Wireless Networks
Optimizing activation and deactivation of base station transmissions provides an instrument for improving energy efficiency in cellular networks. In this paper, we study the problem of performing cell clustering and setting the activation time of each cluster, with the objective of minimizing the sum energy, subject to a time constraint of serving the users' traffic demand. Our optimization framework accounts for inter-cell interference, and, thus, the users' achievable rates depend on cluster formation. We provide mathematical formulations and analysis, and prove the problem's NP hardness. For problem solution, we first apply an optimization method that successively augments the set of variables under consideration, with the capability of approaching global optimum. Then, we derive a second solution algorithm to deal with the trade-off between optimality and the combinatorial nature of cluster formation. Numerical results demonstrate that our solutions achieve more than 40% energy saving over existing schemes, and that the solutions we obtain are within a few percent of deviation from global optimum.
- Open Access
Multi-Antenna Wireless Energy Transfer for Backscatter Communication Systems
We study RF-enabled wireless energy transfer (WET) via energy beamforming, from a multi-antenna energy transmitter (ET) to multiple energy receivers (ERs) in a backscatter communication system, such as RFID, where each ER (or RFID tag) reflects back a portion of the incident signal to the ET (or RFID reader). For such a system, the acquisition of the forward-channel (i.e., ET-to-ER) state information (F-CSI) at the ET is challenging, since the ERs are typically too energy-and-hardware-constrained to estimate or feed back the F-CSI. The ET leverages its observed backscatter signals to estimate the backscatter-channel (i.e., ET-to-ER-to-ET) state information (BS-CSI) directly. We first analyze the harvested energy obtained by using the estimated BS-CSI. Furthermore, we optimize the channel-training energy and the energy allocation weights for different energy beams, for weighted-sum-energy (WSE) maximization and proportional-fair-energy (PFE) maximization. For WET to single ER, we obtain the optimal channel-training energy in a semi-closed form. For WET to multiple ERs, the optimal WET scheme for WSE maximization is shown to use only one energy beam. For PFE maximization, we show it is a biconvex problem, and propose a block-coordinate-descent based algorithm to find the close-to-optimal solution. Numerical results show that with the optimized solutions, the harvested energy suffers slight reduction of less than 10%, compared to that obtained by using the perfect F-CSI. Hence, energy beamforming by using the estimated BS-CSI is promising, as the complexity and energy requirement is shifted from the ERs to the ET.
Open AccessMulti-Antenna Wireless Energy Transfer for Backscatter Communication Systems
We study RF-enabled wireless energy transfer (WET) via energy beamforming, from a multi-antenna energy transmitter (ET) to multiple energy receivers (ERs) in a backscatter communication system, such as RFID, where each ER (or RFID tag) reflects back a portion of the incident signal to the ET (or RFID reader). For such a system, the acquisition of the forward-channel (i.e., ET-to-ER) state information (F-CSI) at the ET is challenging, since the ERs are typically too energy-and-hardware-constrained to estimate or feed back the F-CSI. The ET leverages its observed backscatter signals to estimate the backscatter-channel (i.e., ET-to-ER-to-ET) state information (BS-CSI) directly. We first analyze the harvested energy obtained by using the estimated BS-CSI. Furthermore, we optimize the channel-training energy and the energy allocation weights for different energy beams, for weighted-sum-energy (WSE) maximization and proportional-fair-energy (PFE) maximization. For WET to single ER, we obtain the optimal channel-training energy in a semi-closed form. For WET to multiple ERs, the optimal WET scheme for WSE maximization is shown to use only one energy beam. For PFE maximization, we show it is a biconvex problem, and propose a block-coordinate-descent based algorithm to find the close-to-optimal solution. Numerical results show that with the optimized solutions, the harvested energy suffers slight reduction of less than 10%, compared to that obtained by using the perfect F-CSI. Hence, energy beamforming by using the estimated BS-CSI is promising, as the complexity and energy requirement is shifted from the ERs to the ET.
- Open Access
Throughput Optimization for Massive MIMO Systems Powered by Wireless Energy Transfer
This paper studies a wireless-energy-transfer (WET) enabled massive multiple-input-multiple-output (MIMO) system (MM) consisting of a hybrid data-and-energy access point (H-AP) and multiple single-antenna users. In the WET-MM system, the H-AP is equipped with a large number $M$ of antennas and functions like a conventional AP in receiving data from users, but additionally supplies wireless power to the users. We consider frame-based transmissions. Each frame is divided into three phases: the uplink channel estimation (CE) phase, the downlink WET phase, as well as the uplink wireless information transmission (WIT) phase. Firstly, users use a fraction of the previously harvested energy to send pilots, while the H-AP estimates the uplink channels and obtains the downlink channels by exploiting channel reciprocity. Next, the H-AP utilizes the channel estimates just obtained to transfer wireless energy to all users in the downlink via energy beamforming. Finally, the users use a portion of the harvested energy to send data to the H-AP simultaneously in the uplink (reserving some harvested energy for sending pilots in the next frame). To optimize the throughput and ensure rate fairness, we consider the problem of maximizing the minimum rate among all users. In the large-$M$ regime, we obtain the asymptotically optimal solutions and some interesting insights for the optimal design of WET-MM system. We define a metric, namely, the massive MIMO degree-of-rate-gain (MM-DoRG), as the asymptotic UL rate normalized by $\log(M)$. We show that the proposed WET-MM system is optimal in terms of MM-DoRG, i.e., it achieves the same MM-DoRG as the case with ideal CE.Open AccessThroughput Optimization for Massive MIMO Systems Powered by Wireless Energy Transfer
This paper studies a wireless-energy-transfer (WET) enabled massive multiple-input-multiple-output (MIMO) system (MM) consisting of a hybrid data-and-energy access point (H-AP) and multiple single-antenna users. In the WET-MM system, the H-AP is equipped with a large number $M$ of antennas and functions like a conventional AP in receiving data from users, but additionally supplies wireless power to the users. We consider frame-based transmissions. Each frame is divided into three phases: the uplink channel estimation (CE) phase, the downlink WET phase, as well as the uplink wireless information transmission (WIT) phase. Firstly, users use a fraction of the previously harvested energy to send pilots, while the H-AP estimates the uplink channels and obtains the downlink channels by exploiting channel reciprocity. Next, the H-AP utilizes the channel estimates just obtained to transfer wireless energy to all users in the downlink via energy beamforming. Finally, the users use a portion of the harvested energy to send data to the H-AP simultaneously in the uplink (reserving some harvested energy for sending pilots in the next frame). To optimize the throughput and ensure rate fairness, we consider the problem of maximizing the minimum rate among all users. In the large-$M$ regime, we obtain the asymptotically optimal solutions and some interesting insights for the optimal design of WET-MM system. We define a metric, namely, the massive MIMO degree-of-rate-gain (MM-DoRG), as the asymptotic UL rate normalized by $\log(M)$. We show that the proposed WET-MM system is optimal in terms of MM-DoRG, i.e., it achieves the same MM-DoRG as the case with ideal CE. - Open Access
Wireless Powered Communication: Opportunities and Challenges
The performance of wireless communication is fundamentally constrained by the limited battery life of wireless devices, whose operations are frequently disrupted due to the need of manual battery replacement/recharging. The recent advance in radio frequency (RF) enabled wireless energy transfer (WET) technology provides an attractive solution named wireless powered communication (WPC), where the wireless devices are powered by dedicated wireless power transmitters to provide continuous and stable microwave energy over the air. As a key enabling technology for truly perpetual communications, WPC opens up the potential to build a network with larger throughput, higher robustness, and increased flexibility compared to its battery-powered counterpart. However, the combination of wireless energy and information transmissions also raises many new research problems and implementation issues to be addressed. In this article, we provide an overview of state-of-the-art RF-enabled WET technologies and their applications to wireless communications, with highlights on the key design challenges, solutions, and opportunities ahead.
Open AccessWireless Powered Communication: Opportunities and Challenges
The performance of wireless communication is fundamentally constrained by the limited battery life of wireless devices, whose operations are frequently disrupted due to the need of manual battery replacement/recharging. The recent advance in radio frequency (RF) enabled wireless energy transfer (WET) technology provides an attractive solution named wireless powered communication (WPC), where the wireless devices are powered by dedicated wireless power transmitters to provide continuous and stable microwave energy over the air. As a key enabling technology for truly perpetual communications, WPC opens up the potential to build a network with larger throughput, higher robustness, and increased flexibility compared to its battery-powered counterpart. However, the combination of wireless energy and information transmissions also raises many new research problems and implementation issues to be addressed. In this article, we provide an overview of state-of-the-art RF-enabled WET technologies and their applications to wireless communications, with highlights on the key design challenges, solutions, and opportunities ahead.
- Open Access
Recent Advances in Joint Wireless Energy and Information Transfer
In this paper, we provide an overview of the recent advances in microwave-enabled wireless energy transfer (WET) technologies and their applications in wireless communications. Specifically, we divide our discussions into three parts. First, we introduce the state-of-the-art WET technologies and the signal processing techniques to maximize the energy transfer efficiency. Then, we discuss an interesting paradigm named simultaneous wireless information and power transfer (SWIPT), where energy and information are jointly transmitted using the same radio waveform. At last, we review the recent progress in wireless powered communication networks (WPCN), where wireless devices communicate using the power harvested by means of WET. Extensions and future directions are also discussed in each of these areas.
Open AccessRecent Advances in Joint Wireless Energy and Information Transfer
In this paper, we provide an overview of the recent advances in microwave-enabled wireless energy transfer (WET) technologies and their applications in wireless communications. Specifically, we divide our discussions into three parts. First, we introduce the state-of-the-art WET technologies and the signal processing techniques to maximize the energy transfer efficiency. Then, we discuss an interesting paradigm named simultaneous wireless information and power transfer (SWIPT), where energy and information are jointly transmitted using the same radio waveform. At last, we review the recent progress in wireless powered communication networks (WPCN), where wireless devices communicate using the power harvested by means of WET. Extensions and future directions are also discussed in each of these areas.
- Open Access
Wireless Information and Power Transfer in Multiuser OFDM Systems
In this paper, we study the optimal design for simultaneous wireless information and power transfer (SWIPT) in downlink multiuser orthogonal frequency division multiplexing (OFDM) systems. For information transmission, we consider two types of multiple access schemes, namely, time division multiple access (TDMA) and orthogonal frequency division multiple access (OFDMA). At the receiver side, due to the practical limitation that circuits for harvesting energy from radio signals are not yet able to decode the carried information directly, each user applies either time switching (TS) or power splitting (PS) to coordinate the energy harvesting (EH) and information decoding (ID) processes. For the TDMA-based information transmission, we employ TS at the receivers; for the OFDMA-based information transmission, we employ PS at the receivers. Under the above two scenarios, we address the problem of maximizing the weighted sum-rate over all users by varying the time/frequency power allocation and either TS or PS ratio, subject to a minimum harvested energy constraint on each user as well as a peak and/or total transmission power constraint. For the TS scheme, by an appropriate variable transformation the problem is reformulated as a convex problem, for which the optimal power allocation and TS ratio are obtained by the Lagrange duality method. For the PS scheme, we propose an iterative algorithm to optimize the power allocation, subcarrier (SC) allocation and the PS ratio for each user. The performances of the two schemes are compared numerically as well as analytically for the special case of single-user setup. It is revealed that the peak power constraint imposed on each OFDM SC as well as the number of users in the system play a key role in the rate-energy performance comparison by the two proposed schemes.
Open AccessWireless Information and Power Transfer in Multiuser OFDM Systems
In this paper, we study the optimal design for simultaneous wireless information and power transfer (SWIPT) in downlink multiuser orthogonal frequency division multiplexing (OFDM) systems. For information transmission, we consider two types of multiple access schemes, namely, time division multiple access (TDMA) and orthogonal frequency division multiple access (OFDMA). At the receiver side, due to the practical limitation that circuits for harvesting energy from radio signals are not yet able to decode the carried information directly, each user applies either time switching (TS) or power splitting (PS) to coordinate the energy harvesting (EH) and information decoding (ID) processes. For the TDMA-based information transmission, we employ TS at the receivers; for the OFDMA-based information transmission, we employ PS at the receivers. Under the above two scenarios, we address the problem of maximizing the weighted sum-rate over all users by varying the time/frequency power allocation and either TS or PS ratio, subject to a minimum harvested energy constraint on each user as well as a peak and/or total transmission power constraint. For the TS scheme, by an appropriate variable transformation the problem is reformulated as a convex problem, for which the optimal power allocation and TS ratio are obtained by the Lagrange duality method. For the PS scheme, we propose an iterative algorithm to optimize the power allocation, subcarrier (SC) allocation and the PS ratio for each user. The performances of the two schemes are compared numerically as well as analytically for the special case of single-user setup. It is revealed that the peak power constraint imposed on each OFDM SC as well as the number of users in the system play a key role in the rate-energy performance comparison by the two proposed schemes.
- Open Access
Dynamic Resource Allocation for Multiple-Antenna Wireless Power Transfer
We consider a point-to-point multiple-input-single-output (MISO) system where a receiver harvests energy from a wireless power transmitter to power itself for various applications. The transmitter performs energy beamforming by using an instantaneous channel state information (CSI). The CSI is estimated at the receiver by training via a preamble, and fed back to the transmitter. The channel estimate is more accurate when longer preamble is used, but less time is left for wireless power transfer before the channel changes. To maximize the harvested energy, in this paper, we address the key challenge of balancing the time resource used for channel estimation and wireless power transfer (WPT), and also investigate the allocation of energy resource used for wireless power transfer. First, we consider the general scenario where the preamble length is allowed to vary dynamically. Taking into account the effects of imperfect CSI, the optimal preamble length is obtained online by solving a dynamic programming (DP) problem. The solution is shown to be a threshold-type policy that depends only on the channel estimate power. Next, we consider the scenario in which the preamble length is fixed. The optimal preamble length is optimized offline. Furthermore, we derive the optimal power allocation schemes for both scenarios. For the scenario of dynamic-length preamble, the power is allocated according to both the optimal preamble length and the channel estimate power; while for the scenario of fixed-length preamble, the power is allocated according to only the channel estimate power. The analysis results are validated by numerical simulations. Encouragingly, with optimal power allocation, the harvested energy by using optimized fixed-length preamble is almost the same as the harvested energy by employing dynamic-length preamble, hence allowing a low-complexity WPT system to be implemented in practice.
Open AccessDynamic Resource Allocation for Multiple-Antenna Wireless Power Transfer
We consider a point-to-point multiple-input-single-output (MISO) system where a receiver harvests energy from a wireless power transmitter to power itself for various applications. The transmitter performs energy beamforming by using an instantaneous channel state information (CSI). The CSI is estimated at the receiver by training via a preamble, and fed back to the transmitter. The channel estimate is more accurate when longer preamble is used, but less time is left for wireless power transfer before the channel changes. To maximize the harvested energy, in this paper, we address the key challenge of balancing the time resource used for channel estimation and wireless power transfer (WPT), and also investigate the allocation of energy resource used for wireless power transfer. First, we consider the general scenario where the preamble length is allowed to vary dynamically. Taking into account the effects of imperfect CSI, the optimal preamble length is obtained online by solving a dynamic programming (DP) problem. The solution is shown to be a threshold-type policy that depends only on the channel estimate power. Next, we consider the scenario in which the preamble length is fixed. The optimal preamble length is optimized offline. Furthermore, we derive the optimal power allocation schemes for both scenarios. For the scenario of dynamic-length preamble, the power is allocated according to both the optimal preamble length and the channel estimate power; while for the scenario of fixed-length preamble, the power is allocated according to only the channel estimate power. The analysis results are validated by numerical simulations. Encouragingly, with optimal power allocation, the harvested energy by using optimized fixed-length preamble is almost the same as the harvested energy by employing dynamic-length preamble, hence allowing a low-complexity WPT system to be implemented in practice.