Xi Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xi Gao has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Jie Ren
State Key Laboratory of Materials for Integrated Circuits, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, China
6 shared publications - Huanli Liu
Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, China
3 shared publications - Shucheng Yang
State Key Laboratory of Materials for Integrated Circuits, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, China
3 shared publications - Xiaoping Gao
State Key Laboratory of Materials for Integrated Circuits, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, China
3 shared publications - Minghui Niu
Shanghai Key Laboratory of Superconductor Integrated Circuit Technology, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, China
2 shared publications Wenbo Zhao
Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Science, Shanghai, CHINA
2 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (8) , 1301407
Magnetic Field Uniformity as a Metric for RSFQ Circuit Bias Current Supply Optimization
A key challenge in scaling up rapid single flux quantum (RSFQ) circuits is managing the magnetic interference caused by their bias current distributions. This paper establishes a simulation-driven framework for optimizing RSFQ circuit bias current supply configurations using magnetic field uniformity as the primary metric. Through Ansys HFSS 3D electromagnetic simulations and subsequent data processing, we demonstrated that magnetic field uniformity—rather than absolute intensity—exhibits a stronger correlation with circuit success probability. We developed a quantitative scoring metric to systematically compare and select bias current configurations. Applying this scoring metric to an 8-bit central processing unit (CPU) series, we found that the fully functional version exhibits 6.0% lower magnetic field non-uniformity in the arithmetic logic unit (ALU) block compared to the non-functional one. The proposed method provides a viable approach to optimizing the layout of large-scale RSFQ circuit, specifically to the design of the bias current supply network.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (8) , 1301407
Magnetic Field Uniformity as a Metric for RSFQ Circuit Bias Current Supply Optimization
A key challenge in scaling up rapid single flux quantum (RSFQ) circuits is managing the magnetic interference caused by their bias current distributions. This paper establishes a simulation-driven framework for optimizing RSFQ circuit bias current supply configurations using magnetic field uniformity as the primary metric. Through Ansys HFSS 3D electromagnetic simulations and subsequent data processing, we demonstrated that magnetic field uniformity—rather than absolute intensity—exhibits a stronger correlation with circuit success probability. We developed a quantitative scoring metric to systematically compare and select bias current configurations. Applying this scoring metric to an 8-bit central processing unit (CPU) series, we found that the fully functional version exhibits 6.0% lower magnetic field non-uniformity in the arithmetic logic unit (ALU) block compared to the non-functional one. The proposed method provides a viable approach to optimizing the layout of large-scale RSFQ circuit, specifically to the design of the bias current supply network.
- Open Access
- 23 April 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (5) , 055011
RCLSJ model correction and verification by a proposed test method for DFF’s high-frequency performance
The pursuit of high-speed response and precise reconstruction of phase reversal within Josephson junction constitutes the principal research objectives for the device model in the superconducting single flux quantum (SFQ) circuits. The proposing of the resistive-capacitive-inductive-shunted junction (RCLSJ) model by incorporating a shunted inductance on the classical resistive-capacitive-shunted junction (RCSJ) model, indeed achieves a more accurate description of the Current–Voltage ( I – V ) characteristics of Josephson junctions. However, the effectiveness of the RCLSJ model in dynamic simulations of SFQ circuits has not yet been verified. We proposed a simple and convenient test structure for D flip-flop (DFF) circuits to obtain the variation of its bias margin over a wide frequency sweep range. Post-simulations using the RCLSJ model were performed for DFF circuits. It was found that there are still matching problems between the simulations and tests, especially in the higher frequency region. Based on the junction area structure and layout application under the SIMIT-Nb03 process, a corrected RCLSJ model, designated as the RCLSJv model, was developed. This model mainly reassigns the parasitic inductance of the junction area and introduces correction coefficients by fitting the test data. The validity of the model has been verified through the comprehensive fitting of multiple sets of DFFs’ test data. In comparation with the RCSJ model, the deviation between the test and simulation results was successfully confined within 3%. Notably, in the frequency range above 60 GHz, the matching degree exhibits a remarkable enhancement, with an improvement factor ranging from 2 to 5 times.
- 23 April 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (5) , 055011
Open AccessRCLSJ model correction and verification by a proposed test method for DFF’s high-frequency performance
The pursuit of high-speed response and precise reconstruction of phase reversal within Josephson junction constitutes the principal research objectives for the device model in the superconducting single flux quantum (SFQ) circuits. The proposing of the resistive-capacitive-inductive-shunted junction (RCLSJ) model by incorporating a shunted inductance on the classical resistive-capacitive-shunted junction (RCSJ) model, indeed achieves a more accurate description of the Current–Voltage ( I – V ) characteristics of Josephson junctions. However, the effectiveness of the RCLSJ model in dynamic simulations of SFQ circuits has not yet been verified. We proposed a simple and convenient test structure for D flip-flop (DFF) circuits to obtain the variation of its bias margin over a wide frequency sweep range. Post-simulations using the RCLSJ model were performed for DFF circuits. It was found that there are still matching problems between the simulations and tests, especially in the higher frequency region. Based on the junction area structure and layout application under the SIMIT-Nb03 process, a corrected RCLSJ model, designated as the RCLSJv model, was developed. This model mainly reassigns the parasitic inductance of the junction area and introduces correction coefficients by fitting the test data. The validity of the model has been verified through the comprehensive fitting of multiple sets of DFFs’ test data. In comparation with the RCSJ model, the deviation between the test and simulation results was successfully confined within 3%. Notably, in the frequency range above 60 GHz, the matching degree exhibits a remarkable enhancement, with an improvement factor ranging from 2 to 5 times.
- 15 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (3) , 1-5
A 4-Nb-Layer Cell Library Suitable for LSI Superconductor Digital Circuits
The increase in the single-flux-quantum (SFQ) circuit scale will cause the overall bias current to increase dramatically. The magnetic field interference caused by the current supplied to the SFQ circuit can no longer be ignored. In addition, more complex SFQ circuits require a cell library for more diversified cell types and a more stable operating range to ensure the circuits’ yield. The SIMIT-Nb03P process is then put forward as a tradeoff between process stability and cost. It is compatible with the Nb03 process and does not need an expensive chemical mechanical planarization process. The added new dc power layer is proved to have less interference by simulation. The conversion from Nb03 to Nb03P cell library was very convenient. In addition, some new cells are designed to meet the requirements of complex SFQ circuits. Test circuits of 20 cells of Nb03P were designed and fabricated and were fully verified at low frequencies. The common bias margin of the whole cell library is (–26%, 20%). A variety of large-scale circuits (up to more than 10 000 Josephson junctions) achieve correct function at high frequencies and show good yields on the wafer. It shows that this updated process is cost efficient and suitable for large-scale integration circuits.
- 15 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (3) , 1-5
A 4-Nb-Layer Cell Library Suitable for LSI Superconductor Digital Circuits
The increase in the single-flux-quantum (SFQ) circuit scale will cause the overall bias current to increase dramatically. The magnetic field interference caused by the current supplied to the SFQ circuit can no longer be ignored. In addition, more complex SFQ circuits require a cell library for more diversified cell types and a more stable operating range to ensure the circuits’ yield. The SIMIT-Nb03P process is then put forward as a tradeoff between process stability and cost. It is compatible with the Nb03 process and does not need an expensive chemical mechanical planarization process. The added new dc power layer is proved to have less interference by simulation. The conversion from Nb03 to Nb03P cell library was very convenient. In addition, some new cells are designed to meet the requirements of complex SFQ circuits. Test circuits of 20 cells of Nb03P were designed and fabricated and were fully verified at low frequencies. The common bias margin of the whole cell library is (–26%, 20%). A variety of large-scale circuits (up to more than 10 000 Josephson junctions) achieve correct function at high frequencies and show good yields on the wafer. It shows that this updated process is cost efficient and suitable for large-scale integration circuits.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Timing Evaluation of Passive Transmission Line by RSFQ Ring Oscillator
Passive transmission line (PTL) has been widely applied in rapid single flux quantum (RSFQ) circuits, especially as the first choice of long-distance transmission in large-scale integrated circuits such as arithmetic and logic unit (ALU) and central processing unit (CPU). With the increasing demand of timing regulation, general bias margin is not enough to evaluate the performance of PTL circuits. Timing accuracy including propagation delay of the micro stripe line (MSL) and its delay skew is more critical for clock routine and signal transmission when employing PTL circuits. However, the related reports about the timing information of PTL circuits is limited in the single-value verification of the theoretical MSL's delay. More factors such as bias current, transmission length and system noise should be considered into the evaluation of the PTL circuits. This work focuses on the timing extraction of the designed PTL circuits through different control groups, and evaluates the timing discrepancy between the measurement and simulation. We adopt the method of time accumulation by increasing different lengths of MSL in the loop of the ring oscillator (RO) and subtract each other to evaluate the MSL's propagation delay. We analyzed MSLs of two layers (MSL1 and MSL2). The measured propagation delay of 1 ${\text{mm}}$ MSL is 8.20 ps/mm for MSL1 and 7.66 ps/mm for MSL2, which has a delay skew of 0.30 ${\text{ps}}$ and 0.57 ${\text{ps}}$ from the simulated value (8.23 ${\text{ps}}$ ). Within MSL transmission length of 5 ${\text{mm}}$ , a maximum deviation of 1.2 ${\text{ps}}$ is adopted as time redundancy of PTL circuits applied in ALU and CPU design.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Timing Evaluation of Passive Transmission Line by RSFQ Ring Oscillator
Passive transmission line (PTL) has been widely applied in rapid single flux quantum (RSFQ) circuits, especially as the first choice of long-distance transmission in large-scale integrated circuits such as arithmetic and logic unit (ALU) and central processing unit (CPU). With the increasing demand of timing regulation, general bias margin is not enough to evaluate the performance of PTL circuits. Timing accuracy including propagation delay of the micro stripe line (MSL) and its delay skew is more critical for clock routine and signal transmission when employing PTL circuits. However, the related reports about the timing information of PTL circuits is limited in the single-value verification of the theoretical MSL's delay. More factors such as bias current, transmission length and system noise should be considered into the evaluation of the PTL circuits. This work focuses on the timing extraction of the designed PTL circuits through different control groups, and evaluates the timing discrepancy between the measurement and simulation. We adopt the method of time accumulation by increasing different lengths of MSL in the loop of the ring oscillator (RO) and subtract each other to evaluate the MSL's propagation delay. We analyzed MSLs of two layers (MSL1 and MSL2). The measured propagation delay of 1 ${\text{mm}}$ MSL is 8.20 ps/mm for MSL1 and 7.66 ps/mm for MSL2, which has a delay skew of 0.30 ${\text{ps}}$ and 0.57 ${\text{ps}}$ from the simulated value (8.23 ${\text{ps}}$ ). Within MSL transmission length of 5 ${\text{mm}}$ , a maximum deviation of 1.2 ${\text{ps}}$ is adopted as time redundancy of PTL circuits applied in ALU and CPU design.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (6) , 1-5
Design of Passive Transmission Line by Adjusting Intrinsic Parameters of Josephson Junctions
Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum (RSFQ) circuits by adjusting the Stewart McCumber parameter $\beta_c$ of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from the JJ's modified $\beta_c$ on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. ±30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (6) , 1-5
Design of Passive Transmission Line by Adjusting Intrinsic Parameters of Josephson Junctions
Along with the improvement of integration and the requirement of high-speed operation, the passive transmission line (PTL) plays a significant role in superconducting integrated circuits due to its intrinsic advantage of extremely low propagation delay and low signal loss in long-distance transmission. Good impedance matching is critical to reduce the signal reflection in the transmission line and maximize the power transferred. Based on the PTL wiring layer selection under SIMIT-Nb03 process, we studied the equivalent input/output impedance for Josephson junction (JJ) at the IO port and explored a method of impedance matching in rapid-single-flux-quantum (RSFQ) circuits by adjusting the Stewart McCumber parameter $\beta_c$ of the JJ in the design of the PTL's driver and receiver. Furthermore, the accompanying influence from the JJ's modified $\beta_c$ on the performance of the driver and receiver is evaluated to maximize the profit of the functional circuits. The common-used serial resistor is removed to obtain a balanced bias margin for the PTL circuits. The proposed PTL has been designed and tested based on SIMIT-Nb03 fabrication process. ±30% bias margin for the PTL is achieved at low frequency and high frequency (40 GHz) contrast tests, including operation speed and transmission length as test vector. Additionally, a frequency sweep for 1 mm PTL is performed by the designed ring oscillator on the chip. The maximum working frequency is up to 129 GHz, with a margin duration of 8%.
- 19 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (3) , 1129-1133
JSICsim—An Analog Simulator for Superconductor Integrated Circuit
JSICsim, a new analog simulator for superconductor integrated circuits, is introduced in this paper. It works on SPICE (Simulation Program with Integrated Circuit Emphasis)-style netlists and employs the node voltage analysis method with the parallel computation algorithm. Additionally, the JSICsim simulator focuses on accelerating simulation by using an adjustable simulation accuracy method for large-scale circuit analysis, with a complete simulation platform and GUI integrated into the package. To compare JSICsim with other simulators like PSCAN2, WRspice, and JoSIM, several testbench circuits are simulated and analyzed. The result shows that JSICsim could accelerate the simulation up to 47,16,12 times compared with PSCAN2, WRspice, and JoSIM, respectively. Moreover, JSICsim supports a simulation scale of up to 1 million junctions. Other functionalities such as IV-curve sweeping and thermal noise simulation are also demonstrated.
- 19 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (3) , 1129-1133
JSICsim—An Analog Simulator for Superconductor Integrated Circuit
JSICsim, a new analog simulator for superconductor integrated circuits, is introduced in this paper. It works on SPICE (Simulation Program with Integrated Circuit Emphasis)-style netlists and employs the node voltage analysis method with the parallel computation algorithm. Additionally, the JSICsim simulator focuses on accelerating simulation by using an adjustable simulation accuracy method for large-scale circuit analysis, with a complete simulation platform and GUI integrated into the package. To compare JSICsim with other simulators like PSCAN2, WRspice, and JoSIM, several testbench circuits are simulated and analyzed. The result shows that JSICsim could accelerate the simulation up to 47,16,12 times compared with PSCAN2, WRspice, and JoSIM, respectively. Moreover, JSICsim supports a simulation scale of up to 1 million junctions. Other functionalities such as IV-curve sweeping and thermal noise simulation are also demonstrated.