Zhenlin Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhenlin Lu has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Lei Jia
School of Materials Science and Engineering, Xi’an University of Technology, Xi’an, China
4 shared publications - Zhiguo Xing
National Key Laboratory for Remanufacturing, Academy of Army Armored Forces, Beijing, China
3 shared publications Caixia Wang
School of Materials Science and Engineering, Xi’an University of Technology, Xi’an, People’s Republic of China
2 shared publications- Da Qu
Engineering Research Center of Mechanical Testing Technology and Equipment (Ministry of Education), Chongqing University of Technology, Chongqing 400054, China
2 shared publications - Dongyu He
National Key Laboratory for Remanufacturing, Army Academy of Armored Forces, Beijing 100072, China
2 shared publications - Dongzhou Jia
College of Mechanical Engineering and Automation, Liaoning University of Technology, Jinzhou, China
2 shared publications
Latest Publications
- Open Access
Numerical Study on Heat Transfer Efficiency and Inter-Layer Stress of Microchannel Heat Sinks with Different Geometries
As electronics become more powerful and compact, laminated microchannel heat sinks (MCHSs) are essential for handling high heat flux. This study aims to optimize the MCHS design for improved heat dissipation and structural strength. An orthogonal experiment was established with the average surface temperature of the heat source as the evaluation metric, and the optimal structure was determined through simulation. Finally, cooling uniformity, fluidity, and performance evaluation criterion (PEC) analyses were carried out on the optimal structure. It was determined that the optimal combination was the triangular cavity microchannel (MCTC), with a microchannel width of 0.5 mm, a microchannel distribution density of 60%, and the presence of surface undulation on the microchannels. The result shows that the optimal structure’s peak inter-layer stress is just 34.8% of its longitudinal tensile strength. Compared to the traditional parallel straight microchannel (MCPS), this structure boasts an 8.6 K decrease in the average surface temperature and a temperature variation along specific paths that is only 9.9% of that in traditional designs. Moreover, the optimal design cuts the velocity loss at the microchannel entrance from 75% to 59%. Thus, this research successfully develops an effective optimization strategy for MCHSs.
Open AccessNumerical Study on Heat Transfer Efficiency and Inter-Layer Stress of Microchannel Heat Sinks with Different Geometries
As electronics become more powerful and compact, laminated microchannel heat sinks (MCHSs) are essential for handling high heat flux. This study aims to optimize the MCHS design for improved heat dissipation and structural strength. An orthogonal experiment was established with the average surface temperature of the heat source as the evaluation metric, and the optimal structure was determined through simulation. Finally, cooling uniformity, fluidity, and performance evaluation criterion (PEC) analyses were carried out on the optimal structure. It was determined that the optimal combination was the triangular cavity microchannel (MCTC), with a microchannel width of 0.5 mm, a microchannel distribution density of 60%, and the presence of surface undulation on the microchannels. The result shows that the optimal structure’s peak inter-layer stress is just 34.8% of its longitudinal tensile strength. Compared to the traditional parallel straight microchannel (MCPS), this structure boasts an 8.6 K decrease in the average surface temperature and a temperature variation along specific paths that is only 9.9% of that in traditional designs. Moreover, the optimal design cuts the velocity loss at the microchannel entrance from 75% to 59%. Thus, this research successfully develops an effective optimization strategy for MCHSs.
- Open Access
Numerical Simulation of the Dynamic Behavior Exhibited by Charged Droplets Colliding with Liquid Film
Since droplet collision with walls has become a research hotspot, scholars have conducted a large number of studies on the dynamic behavior of electrically neutral droplets colliding with dry walls. However, with the rapid development of electrostatic spray technology, there is an increasingly urgent need to study the dynamic process of collision between charged droplets and walls. In this paper, considering the actual working conditions of electrostatic spray, an electric field model is introduced based on the two-phase flow field. Through the coupling of a multiphase flow field and electric field and a multiphysics field, the dynamic numerical calculation method is used to explore the collision electrodynamic behavior of charged droplets and liquid film. The dynamic evolution process of the formation and development of the liquid crown in the collision zone was clarified, and the critical velocity and critical Weber number of the rebound, spreading, and splashing of charged droplets were tracked. The distribution characteristics of electrostatic field, pressure field, and velocity field under different working conditions are analyzed, and the dynamic mechanism of the charged droplet collision liquid film under multi-physics coupling is revealed based on the electro-viscous effect. It is confirmed that the external electric field can increase the critical velocity of droplet splashing and fragmentation and promote the spreading and fusion behavior of droplets and liquid films. The influence of the impact angle of charged droplets on the collision behavior was further explored. It was found that the charged droplets not only have a smaller critical angle for fragmentation and splashing, but also have a faster settling and fusion speed.
Open AccessNumerical Simulation of the Dynamic Behavior Exhibited by Charged Droplets Colliding with Liquid Film
Since droplet collision with walls has become a research hotspot, scholars have conducted a large number of studies on the dynamic behavior of electrically neutral droplets colliding with dry walls. However, with the rapid development of electrostatic spray technology, there is an increasingly urgent need to study the dynamic process of collision between charged droplets and walls. In this paper, considering the actual working conditions of electrostatic spray, an electric field model is introduced based on the two-phase flow field. Through the coupling of a multiphase flow field and electric field and a multiphysics field, the dynamic numerical calculation method is used to explore the collision electrodynamic behavior of charged droplets and liquid film. The dynamic evolution process of the formation and development of the liquid crown in the collision zone was clarified, and the critical velocity and critical Weber number of the rebound, spreading, and splashing of charged droplets were tracked. The distribution characteristics of electrostatic field, pressure field, and velocity field under different working conditions are analyzed, and the dynamic mechanism of the charged droplet collision liquid film under multi-physics coupling is revealed based on the electro-viscous effect. It is confirmed that the external electric field can increase the critical velocity of droplet splashing and fragmentation and promote the spreading and fusion behavior of droplets and liquid films. The influence of the impact angle of charged droplets on the collision behavior was further explored. It was found that the charged droplets not only have a smaller critical angle for fragmentation and splashing, but also have a faster settling and fusion speed.
- Open Access
- 30 April 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (5) , 158
Investigation into the Heat Transfer Behavior of Electrostatic Atomization Minimum Quantity Lubrication (EMQL) during Grinding
Electrostatic atomization minimum quantity lubrication (EMQL) technology has been developed to address the need for environmentally friendly, efficient, and low-damage grinding of challenging titanium alloy materials. EMQL leverages multiple physical fields to achieve precise atomization of micro-lubricants, enabling effective lubrication in high temperature, high pressure, and high-speed grinding environments through the use of electric traction. Notably, the applied electric field not only enhances atomization and lubrication capabilities of micro-lubricants but also significantly impacts heat transfer within the grinding zone. In order to explore the influence mechanism of external electric field on spatial heat transfer, this paper first comparatively analyzes the grinding heat under dry grinding, MQL, and EMQL conditions and explores the intensity of the effect of external electric field on the heat transfer behavior in the grinding zone. Furthermore, the COMSOL numerical calculation platform was used to establish an electric field-enhanced (EHD) heat transfer model, clarifying charged particles’ migration rules between poles. By considering the electroviscous effect, the study reveals the evolution of heat transfer structures in the presence of an electric field and its impact on heat transfer mechanisms.
- 30 April 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (5) , 158
Open AccessInvestigation into the Heat Transfer Behavior of Electrostatic Atomization Minimum Quantity Lubrication (EMQL) during Grinding
Electrostatic atomization minimum quantity lubrication (EMQL) technology has been developed to address the need for environmentally friendly, efficient, and low-damage grinding of challenging titanium alloy materials. EMQL leverages multiple physical fields to achieve precise atomization of micro-lubricants, enabling effective lubrication in high temperature, high pressure, and high-speed grinding environments through the use of electric traction. Notably, the applied electric field not only enhances atomization and lubrication capabilities of micro-lubricants but also significantly impacts heat transfer within the grinding zone. In order to explore the influence mechanism of external electric field on spatial heat transfer, this paper first comparatively analyzes the grinding heat under dry grinding, MQL, and EMQL conditions and explores the intensity of the effect of external electric field on the heat transfer behavior in the grinding zone. Furthermore, the COMSOL numerical calculation platform was used to establish an electric field-enhanced (EHD) heat transfer model, clarifying charged particles’ migration rules between poles. By considering the electroviscous effect, the study reveals the evolution of heat transfer structures in the presence of an electric field and its impact on heat transfer mechanisms.
- Open Access
Characterizations on Precipitations in the Cu-Rich Corner of Cu-Ni-Al Ternary Phase Diagram
Three kinds of Cu-Ni-Al alloys, whose chemical compositions are located in the Cu-rich corner of the isothermal section of the Cu-Ni-Al ternary phase diagram, were prepared by melting and casting firstly, and then solution and aging treatments were carried out. The microstructure was characterized and the competitive formation process of Ni-Al intermetallics were discussed. The results show that there are little amounts of NiAl phase at the grain boundary and needle- or particle-like Ni3Al phase inside the Cu matrix in all the as-cast alloys, although they are in the single-phase area. Solution and aging treatments mainly result in the disappearance and precipitation of Ni3Al phase, but the precipitations during aging are much smaller than those in the as-cast alloys. Thermodynamics and kinetics calculation indicate that the NiAl intermetallic wins out in the solidification process because of its lower change in Gibbs free energy, while Ni3Al phase is first to precipitate during aging due to its lower formation enthalpy and required Al concentration. The most important contribution of this work is that it proves that intermetallics can precipitate from the so-called single-phase zone in the Cu-rich corner of the Cu-Ni-Al phase diagram, which is the necessary prerequisite for the realization of high strength and high electrical conductivity.
Open AccessCharacterizations on Precipitations in the Cu-Rich Corner of Cu-Ni-Al Ternary Phase Diagram
Three kinds of Cu-Ni-Al alloys, whose chemical compositions are located in the Cu-rich corner of the isothermal section of the Cu-Ni-Al ternary phase diagram, were prepared by melting and casting firstly, and then solution and aging treatments were carried out. The microstructure was characterized and the competitive formation process of Ni-Al intermetallics were discussed. The results show that there are little amounts of NiAl phase at the grain boundary and needle- or particle-like Ni3Al phase inside the Cu matrix in all the as-cast alloys, although they are in the single-phase area. Solution and aging treatments mainly result in the disappearance and precipitation of Ni3Al phase, but the precipitations during aging are much smaller than those in the as-cast alloys. Thermodynamics and kinetics calculation indicate that the NiAl intermetallic wins out in the solidification process because of its lower change in Gibbs free energy, while Ni3Al phase is first to precipitate during aging due to its lower formation enthalpy and required Al concentration. The most important contribution of this work is that it proves that intermetallics can precipitate from the so-called single-phase zone in the Cu-rich corner of the Cu-Ni-Al phase diagram, which is the necessary prerequisite for the realization of high strength and high electrical conductivity.
- Open Access
- 10 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 956
Study of the Mechanical Properties and Thermal Control Performance of Plasma-Sprayed Alumina Coating on Aluminum Alloy Surface
Thermal control coating is an important means of ensuring that a spacecraft remains operational at high temperatures. Due to limitations regarding preparation technology and material properties, the mechanical properties of the conventional thermal control coatings still need to be improved. To solve this problem, nanostructured alumina coatings (NCs) and conventional alumina coatings (CCs) were prepared using plasma-spraying technology. The microscopic morphology, phase structure, hardness, and thermal control properties (solar absorptance (αs) and emissivity (ε)) of the nanostructured alumina coatings were investigated and compared with those of conventional alumina coatings. The results show that the NC has a higher hardness value (1168.8 HV) and that its reflectivity exceeds 75% in the wavelength range of 446–1586 nm, while a high degree of emissivity of 0.863–0.87 is still maintained at 300–393 K. Furthermore, the results show that these highly reflective properties are related to the phase composition and internal micromorphology of the NC, whereby the solar absorption of the coating is reduced due to the increase in the alpha phase content (21.4%), the high porosity (5.21%) and the nanoparticles favoring the internal scattering. All these properties can improve the performance of this CC coating with low solar absorptance (αs) and high emissivity (ε).
- 10 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 956
Open AccessStudy of the Mechanical Properties and Thermal Control Performance of Plasma-Sprayed Alumina Coating on Aluminum Alloy Surface
Thermal control coating is an important means of ensuring that a spacecraft remains operational at high temperatures. Due to limitations regarding preparation technology and material properties, the mechanical properties of the conventional thermal control coatings still need to be improved. To solve this problem, nanostructured alumina coatings (NCs) and conventional alumina coatings (CCs) were prepared using plasma-spraying technology. The microscopic morphology, phase structure, hardness, and thermal control properties (solar absorptance (αs) and emissivity (ε)) of the nanostructured alumina coatings were investigated and compared with those of conventional alumina coatings. The results show that the NC has a higher hardness value (1168.8 HV) and that its reflectivity exceeds 75% in the wavelength range of 446–1586 nm, while a high degree of emissivity of 0.863–0.87 is still maintained at 300–393 K. Furthermore, the results show that these highly reflective properties are related to the phase composition and internal micromorphology of the NC, whereby the solar absorption of the coating is reduced due to the increase in the alpha phase content (21.4%), the high porosity (5.21%) and the nanoparticles favoring the internal scattering. All these properties can improve the performance of this CC coating with low solar absorptance (αs) and high emissivity (ε).
- Open Access
Simulation on the Direct Powder Rolling Process of Cu Powder by Drucker–Prager/Cap Model and Its Experimental Verification
For better clarifying the influence of processing factors on the forming quality of the direct powder rolling (DPR) process, finite element simulation based on the modified Drucker–Prager/Cap (DPC) model was established and the key physical parameters of the powder were confirmed by experimental measurements. Subsequently, the effect of the main factors in the DPR process, viz., powder gradation, rolling speed and rolling gap, on the density and morphology of a green sheet were discussed by using an orthogonal experiment design followed by experimental verification. The influence of DPR parameters on the density of the green sheet is examined by a range analysis, which can reflect the sensitivity of influencing factors to the forming quality of the green sheet. The larger the range value is, the more sensitive the influencing factor is. This suggests that the quality of the green sheet is mainly influenced by particle gradation. The results show that the density of the resulting DPR green sheet with optimal parameters is mainly 7.5~8.0 g/cm3, reaches 80% of the theoretical density, and the mechanical strength can also afford the transferring process of the green sheet for the next sintering craft. The methods for modeling, obtaining physical parameters and the numerical simulation results can be used to guide rapid formation of the metal sheet by using direct powder rolling craft.
Open AccessSimulation on the Direct Powder Rolling Process of Cu Powder by Drucker–Prager/Cap Model and Its Experimental Verification
For better clarifying the influence of processing factors on the forming quality of the direct powder rolling (DPR) process, finite element simulation based on the modified Drucker–Prager/Cap (DPC) model was established and the key physical parameters of the powder were confirmed by experimental measurements. Subsequently, the effect of the main factors in the DPR process, viz., powder gradation, rolling speed and rolling gap, on the density and morphology of a green sheet were discussed by using an orthogonal experiment design followed by experimental verification. The influence of DPR parameters on the density of the green sheet is examined by a range analysis, which can reflect the sensitivity of influencing factors to the forming quality of the green sheet. The larger the range value is, the more sensitive the influencing factor is. This suggests that the quality of the green sheet is mainly influenced by particle gradation. The results show that the density of the resulting DPR green sheet with optimal parameters is mainly 7.5~8.0 g/cm3, reaches 80% of the theoretical density, and the mechanical strength can also afford the transferring process of the green sheet for the next sintering craft. The methods for modeling, obtaining physical parameters and the numerical simulation results can be used to guide rapid formation of the metal sheet by using direct powder rolling craft.
- Open Access
Electrical Properties of Li+-Doped Potassium Sodium Niobate Coating Prepared by Supersonic Plasma Spraying
The current work aims to compare the effects of systematic A-site substitutions on the electrical properties of potassium sodium niobate (KNN)-based coating. The A-site elements were replaced by Li+ to form (K0.4675Na0.4675Li0.065) NbO3 (KNLN). The pure KNN coating and the Li+-doped potassium sodium niobate (KNLN) coating with dense morphology and single perovskite structure were successfully prepared by supersonic plasma spraying, and the phase composition, microscopic morphology and electrical properties of the two coatings were compared and analyzed in detail by XRD, XPS, three-dimensional morphology and SEM on an Agilent 4294A (Santa Clara, CA, USA) and FE-5000 wide-range ferroelectric performance tester. The results show that: as the polarization voltage increases, the pure KNN coating is flatter and fuller, but the leakage current is large. The KNLN coating has a relatively long hysteresis loop and is easily polarized. The domain deflection responds faster to the external electric field, and the resistance of the domain wall motion to the external electric field is small. The dielectric constant of KNLN coating is 375, which is much higher than that of the pure KNN coating with 125, and the dielectric loss is stable at 0.01, which is lower than that of pure KNN coating at 0.1–0.35. This is because Li+ doping has successfully constructed a polycrystalline phase boundary in which O-T phases coexist, and has higher dielectric properties, piezoelectric properties and ferroelectric properties. At the same time, due to the high-temperature acceleration process in supersonic plasma spraying, the violent volatilization of the alkaline elements Li+, Na+ and K+ leads to the presence of oxygen vacancies and part of Nb4+ in the coating, which seriously affects the electrical properties of the coating.
Open AccessElectrical Properties of Li+-Doped Potassium Sodium Niobate Coating Prepared by Supersonic Plasma Spraying
The current work aims to compare the effects of systematic A-site substitutions on the electrical properties of potassium sodium niobate (KNN)-based coating. The A-site elements were replaced by Li+ to form (K0.4675Na0.4675Li0.065) NbO3 (KNLN). The pure KNN coating and the Li+-doped potassium sodium niobate (KNLN) coating with dense morphology and single perovskite structure were successfully prepared by supersonic plasma spraying, and the phase composition, microscopic morphology and electrical properties of the two coatings were compared and analyzed in detail by XRD, XPS, three-dimensional morphology and SEM on an Agilent 4294A (Santa Clara, CA, USA) and FE-5000 wide-range ferroelectric performance tester. The results show that: as the polarization voltage increases, the pure KNN coating is flatter and fuller, but the leakage current is large. The KNLN coating has a relatively long hysteresis loop and is easily polarized. The domain deflection responds faster to the external electric field, and the resistance of the domain wall motion to the external electric field is small. The dielectric constant of KNLN coating is 375, which is much higher than that of the pure KNN coating with 125, and the dielectric loss is stable at 0.01, which is lower than that of pure KNN coating at 0.1–0.35. This is because Li+ doping has successfully constructed a polycrystalline phase boundary in which O-T phases coexist, and has higher dielectric properties, piezoelectric properties and ferroelectric properties. At the same time, due to the high-temperature acceleration process in supersonic plasma spraying, the violent volatilization of the alkaline elements Li+, Na+ and K+ leads to the presence of oxygen vacancies and part of Nb4+ in the coating, which seriously affects the electrical properties of the coating.
- 16 January 2022
- Published by Taylor & Francis in Composite Interfaces
- Vol. 29 (8) , 971-983
Effect of B4C on bending strength of ZTA ceramic reinforced high chromium cast iron matrix composites
Zirconium dioxide-toughened aluminum oxide (ZTA) ceramic-reinforced high chromium cast iron (HCCI) matrix composites were prepared by vacuum pressure-free infiltration, and the effects of active additive boron carbide (B4C) (10%, 12%) on the interface binding ability was studied systematically. Results showed the wettability between HCCI and ZTA could be improved after the addition of B4C, which could result in a metallurgical combination by forming a transition layer. When the content of B4C additive was 10%, the Brinell hardness of ZTA/HCCI composites reached 645 N/mm2 in the as-infiltration state, and the bending strength was more than twice of HCCI. After heat treatment, the hardness and bending strength increased significantly, which reached 676.1 N/mm2 and more than three times of HCCI, respectively. Graphical Abstract
- 16 January 2022
- Published by Taylor & Francis in Composite Interfaces
- Vol. 29 (8) , 971-983
Effect of B4C on bending strength of ZTA ceramic reinforced high chromium cast iron matrix composites
Zirconium dioxide-toughened aluminum oxide (ZTA) ceramic-reinforced high chromium cast iron (HCCI) matrix composites were prepared by vacuum pressure-free infiltration, and the effects of active additive boron carbide (B4C) (10%, 12%) on the interface binding ability was studied systematically. Results showed the wettability between HCCI and ZTA could be improved after the addition of B4C, which could result in a metallurgical combination by forming a transition layer. When the content of B4C additive was 10%, the Brinell hardness of ZTA/HCCI composites reached 645 N/mm2 in the as-infiltration state, and the bending strength was more than twice of HCCI. After heat treatment, the hardness and bending strength increased significantly, which reached 676.1 N/mm2 and more than three times of HCCI, respectively. Graphical Abstract
- 24 December 2020
- Published by Wiley in International Journal of Quantum Chemistry
- Vol. 121 (8)
First‐principle study of the properties in BaTiO3 and the electronic structure of H2O adsorption on BaTiO3
The properties of BaTiO3 and the electronic structure of H2O adsorption on BaTiO3 were investigated by using first principle calculations based on density functional theory. The calculated results show that the orbital hybridization between Ti and O is stronger than that between Ba and O. With the increase of energy, reflex points in the form of random fluctuation and the anisotropy of crystal clear. Enthalpy and heat capacity varies with temperature rise, while free energy fall. H bonds are formed between the hydrogen of water and the surface oxygen of BaTiO3 and between the hydrogen of hydroxyl and the surface oxygen of BaTiO3. The adsorption process of BaTiO3 adsorbing H2O is a physical process and ΔH < 0, ΔS < 0.
- 24 December 2020
- Published by Wiley in International Journal of Quantum Chemistry
- Vol. 121 (8)
First‐principle study of the properties in BaTiO3 and the electronic structure of H2O adsorption on BaTiO3
The properties of BaTiO3 and the electronic structure of H2O adsorption on BaTiO3 were investigated by using first principle calculations based on density functional theory. The calculated results show that the orbital hybridization between Ti and O is stronger than that between Ba and O. With the increase of energy, reflex points in the form of random fluctuation and the anisotropy of crystal clear. Enthalpy and heat capacity varies with temperature rise, while free energy fall. H bonds are formed between the hydrogen of water and the surface oxygen of BaTiO3 and between the hydrogen of hydroxyl and the surface oxygen of BaTiO3. The adsorption process of BaTiO3 adsorbing H2O is a physical process and ΔH < 0, ΔS < 0.
- Open Access
- 1 June 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (6) , 066520
Effect of Ni/Si mass ratio on microstructure and properties of Cu–Ni–Si alloy
Cu–Ni–Si alloys with 94 wt% Cu content and different Ni/Si mass ratios were prepared by hot pressing sintering, and then solution treatment and ageing treatment were also performed. Microstructure and phase composition along with electrical conductivity and hardness of the alloys under different treating condition was studied, and then the influence of Ni/Si mass ratio was discussed. Results showed that the as-sintered Cu–Ni–Si alloys mainly consisted of α-Cu matrix and some Ni31Si12 particles at the grain boundary as well as δ-Ni2Si phases inside the matrix. After solution treatment, most of the Ni–Si compounds decomposed, but δ-Ni2Si precipitates from the matrix after ageing treatment. With increasing Ni/Si mass ratio, the electrical conductivity and hardness of the alloys increases firstly and then decreases, while a highest combination of them achieved when the mass ratio of Ni/Si was 4:1. The effect of Ni/Si ratio on the electrical conductivity of Cu–Ni–Si alloys can be mainly ascribed to the residual content of Ni/Si in the Cu matrix after ageing treatment. When the mass ratio of Ni/Si is equal to the atomic ratio of δ-Ni2Si phase, most of the Ni and Si atoms would precipitates as δ-Ni2Si, and then the electrical conductivity reaches the highest value.
- 1 June 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (6) , 066520
Open AccessEffect of Ni/Si mass ratio on microstructure and properties of Cu–Ni–Si alloy
Cu–Ni–Si alloys with 94 wt% Cu content and different Ni/Si mass ratios were prepared by hot pressing sintering, and then solution treatment and ageing treatment were also performed. Microstructure and phase composition along with electrical conductivity and hardness of the alloys under different treating condition was studied, and then the influence of Ni/Si mass ratio was discussed. Results showed that the as-sintered Cu–Ni–Si alloys mainly consisted of α-Cu matrix and some Ni31Si12 particles at the grain boundary as well as δ-Ni2Si phases inside the matrix. After solution treatment, most of the Ni–Si compounds decomposed, but δ-Ni2Si precipitates from the matrix after ageing treatment. With increasing Ni/Si mass ratio, the electrical conductivity and hardness of the alloys increases firstly and then decreases, while a highest combination of them achieved when the mass ratio of Ni/Si was 4:1. The effect of Ni/Si ratio on the electrical conductivity of Cu–Ni–Si alloys can be mainly ascribed to the residual content of Ni/Si in the Cu matrix after ageing treatment. When the mass ratio of Ni/Si is equal to the atomic ratio of δ-Ni2Si phase, most of the Ni and Si atoms would precipitates as δ-Ni2Si, and then the electrical conductivity reaches the highest value.