Aleksandr Sulamanidze
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aleksandr Sulamanidze has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Valery Shlyannikov
Institute of Power Engineering and Advanced Technologies, FRC Kazan Scientific Center, Russian Academy of Sciences
3 shared publications - Dmitry Kosov
FRC Kazan Scientific Center of Russian Academy of Sciences, Russia
2 shared publications D. Kosov
1 shared publicationV. Shlyannikov
1 shared publication
Latest Publications
- Open Access
- 5 February 2026
- Published by Gruppo Italiano Frattura
- Vol. 20 (76) , 154-168
The influence of temperature on the deformation behavior, strength and fracture mechanism of the heat-resistant Nickel-based alloy EI698-VD
A detailed investigation was conducted into the fracture mechanisms of cylindrical specimens made of a polycrystalline heat-resistant nickel-based alloy XH73MBTU-VD (EI698-VD), under uniaxial tension in the temperature range of 25–700°C. The presence of both surface and internal defects was identified and subsequently described. The alloy microstructure was observed using scanning electron microscopy and energy-dispersive X-ray spectroscopy methods. In the temperature range of 650 to 700°C, it has been observed that the onset of crack formation occurs at surface defects. Conversely, at lower temperatures, failure was attributed to the process of ductile growth and the coalescence of pores, leading to the formation of an internal crack. At a test temperature of 400°C and above, the Porteven-Le Chatelier effect (serrated flow) was identified. At temperatures of 25, 400 and 550°C, fracture was accompanied by deformation in different slip planes. An increase in the test temperature was found to result in a change in the slope angle of the slip planes. It was observed that at higher temperatures, there was a significant decrease in plasticity. An excess of 90 times the nominal mass composition of Pb content was detected. A possible cause and mechanism of the steep loss of alloy plasticity with increasing temperature is explained.
- 5 February 2026
- Published by Gruppo Italiano Frattura
- Vol. 20 (76) , 154-168
Open AccessThe influence of temperature on the deformation behavior, strength and fracture mechanism of the heat-resistant Nickel-based alloy EI698-VD
A detailed investigation was conducted into the fracture mechanisms of cylindrical specimens made of a polycrystalline heat-resistant nickel-based alloy XH73MBTU-VD (EI698-VD), under uniaxial tension in the temperature range of 25–700°C. The presence of both surface and internal defects was identified and subsequently described. The alloy microstructure was observed using scanning electron microscopy and energy-dispersive X-ray spectroscopy methods. In the temperature range of 650 to 700°C, it has been observed that the onset of crack formation occurs at surface defects. Conversely, at lower temperatures, failure was attributed to the process of ductile growth and the coalescence of pores, leading to the formation of an internal crack. At a test temperature of 400°C and above, the Porteven-Le Chatelier effect (serrated flow) was identified. At temperatures of 25, 400 and 550°C, fracture was accompanied by deformation in different slip planes. An increase in the test temperature was found to result in a change in the slope angle of the slip planes. It was observed that at higher temperatures, there was a significant decrease in plasticity. An excess of 90 times the nominal mass composition of Pb content was detected. A possible cause and mechanism of the steep loss of alloy plasticity with increasing temperature is explained.
- 20 October 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (23)
Thermal‐Induced Inelastic Shrinkage and Swelling Deformation of Heat‐Resistant Polycrystalline Nickel‐Based Alloy
The present article focuses on the novel features of the mechanical behavior and properties of the nickel‐based XH73M (EI698‐VD) alloy under conditions of high temperature. The article reveals the unique effects of thermal‐induced deformation phenomena. The experimental results showed that the alloy exhibited shrinkage (up to 0.0928%), as well as oscillating strain at elevated temperatures in the absence of applied load. The temperature dependence of the thermal‐induced deformation process in the range of 400–650 °C is shown. It is established that the strains are nonquasi‐linear. The change in the electrical resistivity and the correlation of electrical resistance with strain have been investigated using in situ conventional four‐terminal potentiometric method. The data obtained is of critical importance in order to prevent accidents, wear, or a decrease in the efficiency of turbines or components that are subjected to high temperatures for extended periods.
- 20 October 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (23)
Thermal‐Induced Inelastic Shrinkage and Swelling Deformation of Heat‐Resistant Polycrystalline Nickel‐Based Alloy
The present article focuses on the novel features of the mechanical behavior and properties of the nickel‐based XH73M (EI698‐VD) alloy under conditions of high temperature. The article reveals the unique effects of thermal‐induced deformation phenomena. The experimental results showed that the alloy exhibited shrinkage (up to 0.0928%), as well as oscillating strain at elevated temperatures in the absence of applied load. The temperature dependence of the thermal‐induced deformation process in the range of 400–650 °C is shown. It is established that the strains are nonquasi‐linear. The change in the electrical resistivity and the correlation of electrical resistance with strain have been investigated using in situ conventional four‐terminal potentiometric method. The data obtained is of critical importance in order to prevent accidents, wear, or a decrease in the efficiency of turbines or components that are subjected to high temperatures for extended periods.
- 29 July 2024
- Published by Springer Nature in International Journal of Fracture
- Vol. 248 (1-3) , 153-177
Prediction of crack growth in polycrystalline XH73M nickel-based alloy at thermo-mechanical and isothermal fatigue loading
- 29 July 2024
- Published by Springer Nature in International Journal of Fracture
- Vol. 248 (1-3) , 153-177
Prediction of crack growth in polycrystalline XH73M nickel-based alloy at thermo-mechanical and isothermal fatigue loading
- 10 November 2023
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 129, 104182
Isothermal and thermo-mechanical fatigue-crack-growth analysis of XH73M nickel alloy
- 10 November 2023
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 129, 104182
Isothermal and thermo-mechanical fatigue-crack-growth analysis of XH73M nickel alloy
- 23 May 2023
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 125
Crack tip field analysis for thermo-mechanical fatigue loading
- 23 May 2023
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 125
Crack tip field analysis for thermo-mechanical fatigue loading