Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Valery Shlyannikov has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Loading biaxiality and crack tip curvature effects on plastic stress intensity factor behaviour at small-scale and extensive plasticity

    by Aleksandr Zakharov, Valery Shlyannikov

    An elastic–plastic finite element analysis (FEA) was performed for a Mode I plane-strain center-cracked plate (CCP) made of a titanium alloy and subjected to biaxial tension/compression loading. Two crack-tip configurations were considered: a mathematical notch (MN) and a finite radius of curvature (FRC). In the present study, both the J-integral and the plastic stress intensity factor (plastic SIF) were employed to characterize the elastic–plastic stress fields near the crack tip. The distributions of the J-integral and the plastic SIF were evaluated as functions of loading biaxiality and applied stress level. The analysis covered a biaxial stress ratio range extending from equibiaxial tension–compression to equibiaxial tension and included both small-scale yielding (SSY) and extensive plasticity conditions. The results reveal a pronounced coupling between loading biaxiality and crack-tip configuration effects on the fracture parameters. Opposite trends in the variation of the J-integral and the plastic SIF with respect to the biaxial stress ratio and crack-tip geometry were observed. In addition, a comparative assessment of SSY and extensive plasticity regimes was carried out for both crack-tip configurations. It was found that under extensive plasticity conditions the plastic SIF becomes dependent on the crack-tip radius of curvature, whereas under SSY conditions it remains essentially independent of crack-tip geometry.

  • Crack Growth under Isothermal and Thermomechanical Fatigue and Dominant Failure Mechanisms in Heat-Resistant Alloy

    by V. N. Shlyannikov, А. А. Shanyavskiy

    The paper presents an analysis of crack growth rates and an assessment of fracture mechanisms based on the experimental data on isothermal and nonisothermal fatigue. Test results were obtained in the temperature range of 400–650°C under conditions of harmonic fatigue, creep–fatigue interaction, in-phase and out-of-phase thermomechanical cyclic loading. The object of study was heat-resistant nickel-based alloy EI698. After testing, the specimens underwent detailed fractographic analysis using scanning electron microscopy. It was found that the fatigue fracture diagrams were in the following order in terms of crack growth acceleration: isothermal creep–fatigue interaction, nonisothermal in-phase thermomechanical fatigue, isothermal pure fatigue, and nonisothermal out-of-phase thermomechanical fatigue. The crack growth rate curves were arranged according to the dominant intergranular and transgranular fracture mechanisms, and features of transition from one to another were identified.

  • Distinctive Features of Crack Growth Under Cyclic Loading at Elevated Temperature in the Context of Phase‐Field Fracture

    by Valery Shlyannikov, Andrey Tumanov, Ruslan Khamidullin

    The present work investigates the dominant failure mechanisms and crack growth behavior under isothermal and thermomechanical fatigue (TMF), analyzed in terms of energy release rate and phase‐field fracture modeling. The test material consisted of single‐edge notched tension (SENT) specimens fabricated from the nickel‐based heat‐resistant alloy XH73M. Experiments were conducted under conditions of pure fatigue, fatigue–creep interaction, and both in‐phase and out‐of‐phase TMF within the temperature range of 230°C to 650°C. Fractographic analysis based on fatigue fracture diagrams and scanning electron microscopy revealed characteristic features of crack propagation processes under thermomechanical loading. The experimental data on initial, current, and critical values of the energy release rate were incorporated into phase‐field fracture models to simulate the dominant intergranular and transgranular failure mechanisms in XH73M. Furthermore, the study establishes the limitations of employing conventional degradation functions for modeling cyclic fracture processes at elevated temperatures. Summary: The XH73M alloy tests performed for fatigue, creep–fatigue, in‐phase, and out‐of‐phase TMF. The dominant failure mechanisms for TMF are correlated with the energy release rate. The known equations for phase‐field fatigue degradation function have limited capabilities. The XH73M alloy dominant failure mechanisms are modeled by the Voronoi tessellation method.


  • Open Access

    Simulations for Problems of Estimating Structural Residual Life

    by V. N Shlyannikov, Шлянников В. Н

    This paper presents an overview of the accumulated experience in the development and implementation of simulation principles in predicting the residual fatigue life of structural elements during their design and operation in accordance with the concept of tolerance damage. The formulated principles assume the preservation of the accumulated damage under the completed operation of structural elements as heredity of the history of their loading. The proposed sequence of the developed approach implementation includes the analysis of the stress-strain state of the damaged structural element, the development and justification of the geometry and loading conditions in operation, as well as experimental verification and validation by testing simulation models. We analyzed blades and rotating disks of steam turbines and aircraft engines. Configurations and loading conditions of the proposed simulation models reproducing the state of the critical zones of the structural elements are presented. Combinations of conditions of a multi-axial stress state, defect shape, operating temperature and profile of the in-service deformation cycle are considered. Numerical solutions are obtained for the most complex situations of modeling the behavior of surface part-through defects with a combination of mixed modes by separation, longitudinal and transverse shear. The achieved results of residual life estimations are attributed to the composition of original testing devices and methods.

  • Open Access

    ANSYS implementation of the phase field fracture approach

    by Dmitry Kosov, Andrey Tumanov, Valery Shlyannikov

    In this study, we present a new implementation of the phase field fracture approach in the finite element code ANSYS and its numerical background. The framework is general, and is supported by addressing several classical 2D boundary value problems as well as the ductile fracture and 3D surface flaws behaviors of particular interest. The 3D implementation exploits the analogy between the phase field formulations and the magnetic vector potential equation. The influence of the mode mixity and biaxiality loading conditions of the cracked bodies on phase fields is evaluated as a function of the crack length scale parameter, characterising the scale at which damage effects become significant. As a result of the FE calculations of phase field distributions for propagating cracks, the effects of both the fracture mode and the biaxial stress-strain state are determined. The size of the fracture process zone or damaged region is determined across a wide range of cracked body loading conditions. Developed code: https://github.com/Andrey-Fog/ANSYS-USERELEMENT-PHFLD.


  • Open Access

    Elastic and nonlinear crack tip solutions comparison with respect to failure probability

    by Valery Shlyannikov, Andrey Tumanov, Nataliya Boychenko

    This study represents a methodology to assess the probability of failure based on three the driving force formulations defined by the corresponding brittle and ductile fracture criteria for compact and bending specimens made of 34XIBNIA and S55C steels. The elastic stress intensity factor (SIF) and two types of the non-linear plastic SIFs were considered as the driving force or generalized parameter (GP) to determine the probability of failure assuming a three-parameter Weibull distribution. The elastic SIF were experimentally obtained for studied materials and specimen geometries whereas the plastic SIFs were numerically calculated for the same material properties, specimen configurations and loading conditions according to classical J(2) and strain gradient plasticity theories. Different specimen types with varying relative crack lengths and thicknesses were investigated. Proposed the normalized generalized parameter accounting for brittle or ductile fracture can be used as a suitable failure variable that is confirmed by comparison of the obtained failure cumulative distribution functions based on the three studied GPs.


  • Open Access

    Numerical and experimental investigation of mixed‐mode crack growth in aluminum alloys

    by Daniele Amato, Rustam Yarullin, Valery Shlyannikov, Roberto Citarella

    Fatigue crack growth in Al 2024 and Al 7050 specimens was assessed experimentally and numerically. In the experimental investigation, various specimen configurations and loading conditions were used to achieve pure mode I, pure mode II, and mixed mode I/II, I/III, and I/II/III. Sample configurations were as follows: first, compact tension shear (CTS) specimen to reproduce pure mode‐I and pure initial mode‐II loading conditions; second, surface crack tension (SCT) specimen to analyze the behavior of semielliptical surface cracks in mode‐I and mixed‐mode conditions; and third, hollow cylindrical (HC) specimen with initial semielliptical surface crack to analyze fatigue crack growth under complex stress state. In the numerical study, finite element method (FEM) simulations were performed by means of FRANC3D and ABAQUS solver. The numerical predictions were validated with the experimental results. These predictions resulted to be accurate estimation of the crack growth across the broad range of the investigated loading conditions.