Hussain Gharehbaghi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hussain Gharehbaghi has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Amin Farrokhabadi
Department of Mechanical Engineering, Tarbiat Modares University
2 shared publicationsAmir Hossein Behravesh
Department of Mechanical Engineering, Tarbiat Modares University
2 shared publications- Abdulla Almomani1 shared publication
- Ali Moazemi Goudarzi
Mechanical Engineering department, Babol Noshirvani University of Technology, Babol, Iran
1 shared publication - Amin Farrokhabadi
Tarbiat Modares University
1 shared publication Amir Bolouri
School of Engineering, University of the West of England, Bristol, UK
1 shared publication
Latest Publications
- Open Access
- 17 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 400-417
Numerical and experimental study on the energy absorption characteristics of thin-walled auxetic cylindrical tubes with varying porosity
- 17 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 400-417
Open AccessNumerical and experimental study on the energy absorption characteristics of thin-walled auxetic cylindrical tubes with varying porosity
- Open Access
- 17 May 2025
- Published by Elsevier in Forces in Mechanics
- Vol. 19
Investigation of creep-fatigue interaction in steam turbine rotor
- 17 May 2025
- Published by Elsevier in Forces in Mechanics
- Vol. 19
Open AccessInvestigation of creep-fatigue interaction in steam turbine rotor
- Open Access
- 28 November 2024
- Published by Elsevier in Composites Part C: Open Access
- Vol. 15
Experimental and numerical investigation of energy absorption in honeycomb structures based on lozenge grid unit cells under various loading angles
- 28 November 2024
- Published by Elsevier in Composites Part C: Open Access
- Vol. 15
Open AccessExperimental and numerical investigation of energy absorption in honeycomb structures based on lozenge grid unit cells under various loading angles
- Open Access
- 11 October 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (11) , 115941
Enhancing auxetic gradient structures for hip joint implants to optimize stress shielding reduction
This study investigates the design and optimization of a porous hip implant to mitigate stress shielding. Initially, the focus was on determining the elastic modulus of a three-dimensional auxetic structure, primarily in the y-direction. Various methods—numerical, analytical, and experimental—were used to assess the elastic properties. Additive manufacturing was employed to create samples, which were then tested for their elastic properties through compression testing. The results revealed a strong correlation between the elastic modulus values obtained from simulations and experimental tests in the y-direction. To further enhance the implant’s performance and reduce stress shielding at the implant-bone interface, a gradient structure was introduced. This gradient design progressively increases the elastic modulus away from the bone contact surfaces, aligning closely with the bone’s modulus at the interface. The elastic modulus of this gradient structure was computed using Abaqus software and validated through analytical methods in MATLAB, with a minimal 4.8% difference between the two approaches, demonstrating high agreement. The application of a genetic algorithm enabled the creation of a porous hip implant tailored to minimize stress shielding throughout its structure. This innovative approach, integrating numerical, analytical, and experimental techniques with gradient structures, holds promise for improving hip implant performance and enhancing patient outcomes by reducing stress-shielding complications.
- 11 October 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (11) , 115941
Open AccessEnhancing auxetic gradient structures for hip joint implants to optimize stress shielding reduction
This study investigates the design and optimization of a porous hip implant to mitigate stress shielding. Initially, the focus was on determining the elastic modulus of a three-dimensional auxetic structure, primarily in the y-direction. Various methods—numerical, analytical, and experimental—were used to assess the elastic properties. Additive manufacturing was employed to create samples, which were then tested for their elastic properties through compression testing. The results revealed a strong correlation between the elastic modulus values obtained from simulations and experimental tests in the y-direction. To further enhance the implant’s performance and reduce stress shielding at the implant-bone interface, a gradient structure was introduced. This gradient design progressively increases the elastic modulus away from the bone contact surfaces, aligning closely with the bone’s modulus at the interface. The elastic modulus of this gradient structure was computed using Abaqus software and validated through analytical methods in MATLAB, with a minimal 4.8% difference between the two approaches, demonstrating high agreement. The application of a genetic algorithm enabled the creation of a porous hip implant tailored to minimize stress shielding throughout its structure. This innovative approach, integrating numerical, analytical, and experimental techniques with gradient structures, holds promise for improving hip implant performance and enhancing patient outcomes by reducing stress-shielding complications.
- 27 May 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (21) , 5234-5252
Investigation of energy absorption performances of a 3D printed fiber-reinforced bio-inspired cellular structure under in-plane compression loading
- 27 May 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (21) , 5234-5252
Investigation of energy absorption performances of a 3D printed fiber-reinforced bio-inspired cellular structure under in-plane compression loading
- 18 January 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (14) , 2955-2964
Introducing a new hybrid surface strut-based lattice structure with enhanced energy absorption capacity
The present study aims to assess a new lattice structure with high energy absorption capacity. Lattice structures with surface-based unit cell have higher energy absorption than those with strut-based unit cell. A new lattice structure is presented by adding the strut to the surface-based unit cell which has a higher energy absorption capacity than the lattice structures with surface-based unit cell. First, the high energy absorption capacity of surface-based lattice structures was evaluated by adding the strut. Such analyzes are conducted by providing a numerical model which considers the elasto-plasto-damage properties of materials under tension and compression. Then, a number of experimental samples were made using additive manufacturing and the compression test was performed. The results of finite element analysis were consistent with those of the experimental results. Based on the results, adding strut increased the energy absorption for surface-based lattice structures by about 106%. Finally, the effect of the ratio of geometric parameters of the unit cell on its mechanical behavior was evaluated.
- 18 January 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (14) , 2955-2964
Introducing a new hybrid surface strut-based lattice structure with enhanced energy absorption capacity
The present study aims to assess a new lattice structure with high energy absorption capacity. Lattice structures with surface-based unit cell have higher energy absorption than those with strut-based unit cell. A new lattice structure is presented by adding the strut to the surface-based unit cell which has a higher energy absorption capacity than the lattice structures with surface-based unit cell. First, the high energy absorption capacity of surface-based lattice structures was evaluated by adding the strut. Such analyzes are conducted by providing a numerical model which considers the elasto-plasto-damage properties of materials under tension and compression. Then, a number of experimental samples were made using additive manufacturing and the compression test was performed. The results of finite element analysis were consistent with those of the experimental results. Based on the results, adding strut increased the energy absorption for surface-based lattice structures by about 106%. Finally, the effect of the ratio of geometric parameters of the unit cell on its mechanical behavior was evaluated.
- 27 December 2022
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Mechanical Engineering
- Vol. 47 (4) , 1777-1785
Investigation of the Effect of Welding Residual Stress on Natural Frequencies, Experimental and Numerical Study
- 27 December 2022
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Mechanical Engineering
- Vol. 47 (4) , 1777-1785
Investigation of the Effect of Welding Residual Stress on Natural Frequencies, Experimental and Numerical Study