Eva Pasquier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Eva Pasquier has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Gary Chinga-Carrasco
RISE PFI, Trondheim, Norway
3 shared publications - Jost Ruwoldt
RISE PFI AS, Høgskoleringen 6B, 7491 Trondheim, Norway
2 shared publications Amalie Solberg
RISE PFI, Høgskoleringen 6b, Trondheim, Norway
1 shared publication- Amalie Solberg
RISE-PFI
1 shared publication - Anders Ståhlberg
Department of Laboratory Medicine, Sahlgrenska Center for Cancer Research, Institute of Biomedicine, Sahlgrenska Academy, University of Gothenburg, Gothenburg, Sweden
1 shared publication - Isabel Hui
Tissue Engineering + Biofabrication Laboratory, Department of Health Sciences & Technology, ETH Zürich, Otto-Stern-Weg 7, 8093 Zürich, Switzerland
1 shared publication
Latest Publications
- Open Access
- 29 September 2024
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 21 (1)
Effect of Raw Material and Process Conditions During the Dry Forming of CTMP Fibers for Molded Pulp Products
- 29 September 2024
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 21 (1)
Open AccessEffect of Raw Material and Process Conditions During the Dry Forming of CTMP Fibers for Molded Pulp Products
- Open Access
- 17 February 2024
- Published by Elsevier in Journal of Cleaner Production
- Vol. 445
Development of a beverage carton closure cap based on 100% wood pulp fibres
- 17 February 2024
- Published by Elsevier in Journal of Cleaner Production
- Vol. 445
Open AccessDevelopment of a beverage carton closure cap based on 100% wood pulp fibres
- Open Access
- 20 September 2023
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 147, 106136
Biocomposites containing poly(lactic acid) and chitosan for 3D printing – Assessment of mechanical, antibacterial and in vitro biodegradability properties
- 20 September 2023
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 147, 106136
Open AccessBiocomposites containing poly(lactic acid) and chitosan for 3D printing – Assessment of mechanical, antibacterial and in vitro biodegradability properties
- Open Access
- 3 June 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (6) , 682
Polysaccharides and Structural Proteins as Components in Three-Dimensional Scaffolds for Breast Cancer Tissue Models: A Review
Breast cancer is the most common cancer among women, and even though treatments are available, efficiency varies with the patients. In vitro 2D models are commonly used to develop new treatments. However, 2D models overestimate drug efficiency, which increases the failure rate in later phase III clinical trials. New model systems that allow extensive and efficient drug screening are thus required. Three-dimensional printed hydrogels containing active components for cancer cell growth are interesting candidates for the preparation of next generation cancer cell models. Macromolecules, obtained from marine- and land-based resources, can form biopolymers (polysaccharides such as alginate, chitosan, hyaluronic acid, and cellulose) and bioactive components (structural proteins such as collagen, gelatin, and silk fibroin) in hydrogels with adequate physical properties in terms of porosity, rheology, and mechanical strength. Hence, in this study attention is given to biofabrication methods and to the modification with biological macromolecules to become bioactive and, thus, optimize 3D printed structures that better mimic the cancer cell microenvironment. Ink formulations combining polysaccharides for tuning the mechanical properties and bioactive polymers for controlling cell adhesion is key to optimizing the growth of the cancer cells.
- 3 June 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (6) , 682
Open AccessPolysaccharides and Structural Proteins as Components in Three-Dimensional Scaffolds for Breast Cancer Tissue Models: A Review
Breast cancer is the most common cancer among women, and even though treatments are available, efficiency varies with the patients. In vitro 2D models are commonly used to develop new treatments. However, 2D models overestimate drug efficiency, which increases the failure rate in later phase III clinical trials. New model systems that allow extensive and efficient drug screening are thus required. Three-dimensional printed hydrogels containing active components for cancer cell growth are interesting candidates for the preparation of next generation cancer cell models. Macromolecules, obtained from marine- and land-based resources, can form biopolymers (polysaccharides such as alginate, chitosan, hyaluronic acid, and cellulose) and bioactive components (structural proteins such as collagen, gelatin, and silk fibroin) in hydrogels with adequate physical properties in terms of porosity, rheology, and mechanical strength. Hence, in this study attention is given to biofabrication methods and to the modification with biological macromolecules to become bioactive and, thus, optimize 3D printed structures that better mimic the cancer cell microenvironment. Ink formulations combining polysaccharides for tuning the mechanical properties and bioactive polymers for controlling cell adhesion is key to optimizing the growth of the cancer cells.