ASAlakshyender Singh

Alakshyender Singh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alakshyender Singh has a total of 2 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Isolated Power Factor Corrected High-Gain AC–DC Buck-Boost Converter-Based Single-Stage LEV Battery Charger

    by Alakshyender Singh, Jitendra Gupta, Bhim Singh

    A single-stage on-board charger for light electric vehicle (LEV) batteries, based on an isolated high step-down gain bridgeless AC-DC buck-boost converter, is presented in this study. This charger offers several advantages over a conventional two-stage charger, which include reduction in overall component count, reduced cost and size, elimination of electrolytic DC Link capacitor, reduction in control effort, and better dynamic voltage regulation. An overall efficiency of presented charger is enhanced by using bridgeless configuration of converter, which reduces conduction losses associated with a diode bridge rectifier. Additionally, converter is designed to operate in discontinuous conduction mode (DCM), which accords charger supplementary benefits of zero current switching to one diode and two switches of converter without a use of any auxiliary circuit. DCM operation leads to diminished size of magnetics and further, facilitates reduction of number of sensors required and control effort for implementation of various charging methodologies viz. constant current (CC) and constant voltage (CV). At supply end, charger operates at high power factor while exhibiting high voltage conversion ratio. This study authenticates feasibility of charger and its performance during both steady and dynamic states using simulations. Practical implementation and validation of theoretical features of charger are undertaken using a 450 W test bench setup, which attempts to emulate simulated results in real time environment


  • Bridgeless Modified High-Step-Up Gain SEPIC PFC Converter Based Charger for Light EVs Battery

    by Alakshyender Singh, Jitendra Gupta, Bhim Singh

    This study presents a two-stage on-board charger for light electric vehicles (LEVs) with low voltage battery (24-72V). The front-end of the charger has characteristics of high voltage conversion ratio and unity power factor operation achieved by a bridgeless high gain modified SEPIC converter. The high voltage conversion ratio enables the front-end to operate over a wide range of input voltages. At the back-end of the charger, an isolated positive output Luo DC-DC converter is employed to regulate the charging profile of the LEV battery under constant current (CC) and constant voltage (CV) charging modes. The presented charger operates in discontinuous conduction mode (DCM), which has dual advantages of having inherent feature of power factor correction (PFC) at the supply end along with significantly reducing the complexity of control mechanism, thereby reducing the cost and effort of control implementation. The operational analysis and design of the presented charger in DCM are covered in detail in this study and the same are further validated by means of simulations. A 650 W test bench setup is developed to authenticate the theoretical performance by means of experimental results. The experimental performance of the front-end is finally compared with other PFC topologies to highlight the merits and demerits of the presented charger.


  • Design and Control of Two Stage Battery Charger for Low Voltage Electric Vehicles Using High Gain Buck-Boost PFC AC-DC Converter

    by Alakshyender Singh, Jitendra Gupta, Bhim Singh

    The design and control of a two-stage onboard battery charger (OBC) for the low-voltage electric vehicle (LVEVs) are presented in this study. The presented charger operates over a wide range of AC input voltage at high power factor. The presented charger utilizes a bridgeless high gain high power factor AC-DC converter with continuous input current characteristics at its front end. At the back end of the charger, an isolated Cuk DC-DC converter is employed to control and implement different battery charging modes, viz. constant current (CC) and constant voltage (CV) charging profiles. The presented AC-DC converter operates under discontinuous current mode (DCM) operation and achieves minimum control complexity at the AC-DC stage. The DCM design and high voltage conversion ratio allow it to function reliably over a comprehensive range of input and intermediate DC link voltage. This study covers the charger's design for a power rating of 650 W and output battery voltage of 24 to 72 V. The overall operational analysis and effectiveness of the design are verified through both simulations and experimental implementation and the performance is compared with other contemporary power factor correction (PFC) topologies on various parameters.