Yongqing Zeng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yongqing Zeng has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
Xiaohong Liu
College of Civil Engineering and Architecture, Hunan Institute of Science and Technology, Yueyang, China
5 shared publicationsHaibo Li
State Key Laboratory of Geomechanics and Geotechnical Engineering, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan, China
4 shared publicationsHong Zuo
4 shared publicationsWeidong Hu
College of Civil Engineering and Architecture, Hunan Institute of Science and Technology, Yueyang, China
4 shared publicationsXinnian Zhu
College of Civil Engineering and Architecture, Hunan Institute of Science and Technology, Yueyang, China
4 shared publicationsJinlin Jiang
3 shared publications
Latest Publications
- Open Access
- 14 January 2026
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 14 (2) , 329-353
Research on the influence of pile diameter on the pile-anchor support system for deep foundation pit adjacent to the existing structure
The excavation of complex deep foundation pit poses significant risks to the safety of adjacent existing structures. To investigate the force and deformation characteristics of deep foundation pit, this study focuses on the pile-anchor support system of a deep foundation pit for a third-line ship lock on the Xiangjiang River. Model tests and numerical modeling analyses were conducted to evaluate the influence of pile diameters (1.0 m ≤ d ≤ 2.0 m) on the force and deformation characteristics of pile-anchor support system in deep foundation pit adjacent to buildings. The results indicate the following: (1) The variation pattern of horizontal displacement at the top of pile in the model test is consistent with that observed in the numerical simulation. The bending moment of the pile body exhibits an “S”-shaped distribution, confirming the reliability of numerical model. (2) The horizontal displacement curve of pile body presents a “bulging belly” shape, with smaller displacements at the top and bottom and larger displacements in the middle. The curvature of displacement decreases as the pile diameter increases. (3) Larger pile diameters result in greater bending moments in the pile body, smaller changes in the positions of positive and negative bending moment extremes, and reduced surface settlement. (4) The uplift at the bottom of foundation pit initially decreases and then increases, forming a “hooked” curve. The influence of pile diameter on bottom uplift is relatively minor. (5) Larger pile diameters promote a transition in the active failure mode from semi-infinite soil to finite soil, with d = 1.5 m serving as the critical value for finite soil conditions. (6) Based on economic considerations, d = 1.5 m is determined to be the optimal pile diameter. (7) The active deformation sliding surface of finite soil behind piles is a curve or polyline that is higher than the heel of wall and returns to the adjacent buildings. This study provides valuable experimental data for investigating finite soil deformation behind piles in the pile-anchor support system for deep foundation pit, offering both theoretical significance and practical engineering value.
- 14 January 2026
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 14 (2) , 329-353
Open AccessResearch on the influence of pile diameter on the pile-anchor support system for deep foundation pit adjacent to the existing structure
The excavation of complex deep foundation pit poses significant risks to the safety of adjacent existing structures. To investigate the force and deformation characteristics of deep foundation pit, this study focuses on the pile-anchor support system of a deep foundation pit for a third-line ship lock on the Xiangjiang River. Model tests and numerical modeling analyses were conducted to evaluate the influence of pile diameters (1.0 m ≤ d ≤ 2.0 m) on the force and deformation characteristics of pile-anchor support system in deep foundation pit adjacent to buildings. The results indicate the following: (1) The variation pattern of horizontal displacement at the top of pile in the model test is consistent with that observed in the numerical simulation. The bending moment of the pile body exhibits an “S”-shaped distribution, confirming the reliability of numerical model. (2) The horizontal displacement curve of pile body presents a “bulging belly” shape, with smaller displacements at the top and bottom and larger displacements in the middle. The curvature of displacement decreases as the pile diameter increases. (3) Larger pile diameters result in greater bending moments in the pile body, smaller changes in the positions of positive and negative bending moment extremes, and reduced surface settlement. (4) The uplift at the bottom of foundation pit initially decreases and then increases, forming a “hooked” curve. The influence of pile diameter on bottom uplift is relatively minor. (5) Larger pile diameters promote a transition in the active failure mode from semi-infinite soil to finite soil, with d = 1.5 m serving as the critical value for finite soil conditions. (6) Based on economic considerations, d = 1.5 m is determined to be the optimal pile diameter. (7) The active deformation sliding surface of finite soil behind piles is a curve or polyline that is higher than the heel of wall and returns to the adjacent buildings. This study provides valuable experimental data for investigating finite soil deformation behind piles in the pile-anchor support system for deep foundation pit, offering both theoretical significance and practical engineering value.
- Open Access
- 18 July 2025
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 13 (4) , 786-803
Research on the influence of width-height ratio and internal friction angle of the TT mode on the trapezoidal sliding surface of backfill behind the retaining wall
The morphology of sliding surface is an important factor in the earth pressure analysis. To study the characteristics of the sliding surface of backfill behind a rigid wall, taking the translational mode of wall (TT model) as an example, a model test was conducted through a self-made test device, and numerical modelling and theoretical analysis were carried out. The research shows: (1) The finite sliding surface morphology starts from the heel of the wall and consists of multiple “straight lines”. The smaller the width-height ratio and the internal friction angle, the more the number of straight line segments of the finite sliding surface. (2) The “length factor” of the sliding surface is introduced and defined. Through normalisation processing, the width-height ratio, internal friction angle, and length factor are linearly fitted, showing a high degree of linear correlation. (3) The study of the width-height ratio, internal friction angle, and length factor yields a binary quadratic surface function, which shows a high degree of linear correlation. The study fills the research gap of the joint influence of the width-height ratio and internal friction angle on the folded-line type sliding surface. It proposes a quantitative calculation formula for the determination of the finite soil.
- 18 July 2025
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 13 (4) , 786-803
Open AccessResearch on the influence of width-height ratio and internal friction angle of the TT mode on the trapezoidal sliding surface of backfill behind the retaining wall
The morphology of sliding surface is an important factor in the earth pressure analysis. To study the characteristics of the sliding surface of backfill behind a rigid wall, taking the translational mode of wall (TT model) as an example, a model test was conducted through a self-made test device, and numerical modelling and theoretical analysis were carried out. The research shows: (1) The finite sliding surface morphology starts from the heel of the wall and consists of multiple “straight lines”. The smaller the width-height ratio and the internal friction angle, the more the number of straight line segments of the finite sliding surface. (2) The “length factor” of the sliding surface is introduced and defined. Through normalisation processing, the width-height ratio, internal friction angle, and length factor are linearly fitted, showing a high degree of linear correlation. (3) The study of the width-height ratio, internal friction angle, and length factor yields a binary quadratic surface function, which shows a high degree of linear correlation. The study fills the research gap of the joint influence of the width-height ratio and internal friction angle on the folded-line type sliding surface. It proposes a quantitative calculation formula for the determination of the finite soil.
- Open Access
- 2 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-25
Numerical simulation of topographic propagation law of vibration wave in liquid carbon dioxide phase transition fracturing blasting
Compared to the high-risk hazards of explosive blasting, liquid carbon dioxide phase transition fracturing technology, as a new technology, can be used as a supplementary method that is not suitable for explosive blasting sites. Liquid carbon dioxide phase transition fracturing blasting is different from explosive blasting; for the application of liquid carbon dioxide phase transition fracturing blasting in the process of rock excavation, there is still a lack of research on the vibration effect of terrain on the topographic propagation law of vibration wave, so it is of certain significance to study the vibration wave propagation rule of liquid carbon dioxide phase transition fracturing blasting under different terrain conditions. The study on the terrain propagation law of vibration waves in liquid carbon dioxide phase change fracturing blasting was carried out. Firstly, the field CO2 blasting tests and PPV measurements are described, and the applicability of UDEC software to blasting analysis and the determination of the load for liquid carbon dioxide phase change fracturing blasting were introduced. Then, the selection of physical and mechanical parameters, viscous boundary conditions, and damping for the site rock mass was elaborated in detail. Finally, the numerical models are established for liquid carbon dioxide phase transition fracturing blasting in flat, concave, convex, and slope terrain. The influence laws of flat, concave, convex, and slope terrain on the peak particle velocity of liquid carbon dioxide phase transition fracturing blasting are obtained. In actual CO2 blasting sites, the safe PPV vibration control standards can be proposed based on different terrain by applying the proposed terrain prediction formula, solving the challenge of quantitatively analyzing the terrain effects of CO2 blasting. The research results have certain guiding significance for predicting the peak particle velocity in advance and controlling the vibration effect of high-pressure carbon dioxide fracturing blasting.
- 2 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-25
Open AccessNumerical simulation of topographic propagation law of vibration wave in liquid carbon dioxide phase transition fracturing blasting
Compared to the high-risk hazards of explosive blasting, liquid carbon dioxide phase transition fracturing technology, as a new technology, can be used as a supplementary method that is not suitable for explosive blasting sites. Liquid carbon dioxide phase transition fracturing blasting is different from explosive blasting; for the application of liquid carbon dioxide phase transition fracturing blasting in the process of rock excavation, there is still a lack of research on the vibration effect of terrain on the topographic propagation law of vibration wave, so it is of certain significance to study the vibration wave propagation rule of liquid carbon dioxide phase transition fracturing blasting under different terrain conditions. The study on the terrain propagation law of vibration waves in liquid carbon dioxide phase change fracturing blasting was carried out. Firstly, the field CO2 blasting tests and PPV measurements are described, and the applicability of UDEC software to blasting analysis and the determination of the load for liquid carbon dioxide phase change fracturing blasting were introduced. Then, the selection of physical and mechanical parameters, viscous boundary conditions, and damping for the site rock mass was elaborated in detail. Finally, the numerical models are established for liquid carbon dioxide phase transition fracturing blasting in flat, concave, convex, and slope terrain. The influence laws of flat, concave, convex, and slope terrain on the peak particle velocity of liquid carbon dioxide phase transition fracturing blasting are obtained. In actual CO2 blasting sites, the safe PPV vibration control standards can be proposed based on different terrain by applying the proposed terrain prediction formula, solving the challenge of quantitatively analyzing the terrain effects of CO2 blasting. The research results have certain guiding significance for predicting the peak particle velocity in advance and controlling the vibration effect of high-pressure carbon dioxide fracturing blasting.
- 3 February 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (20) , 16855-16867
Passive Earth Pressures on Cantilever Retaining Walls Under Non-ultimate State in Narrow Excavation
- 3 February 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (20) , 16855-16867
Passive Earth Pressures on Cantilever Retaining Walls Under Non-ultimate State in Narrow Excavation
- Open Access
- 8 January 2025
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 13 (2) , 344-361
The critical width-height ratio of finite soil behind retaining wall considering the compaction degree of fill under RB mode
The compaction degree of fill is an important index for quality control of slope support engineering. Aiming at the influence factor of the compaction degree of fill, the effect of the compaction degree of fill on the characteristics of active fracture surface and the critical width-height ratio of finite soil under the RB model was investigated through laboratory model test and numerical simulation. The primary research findings are as follows: (1) Under RB mode, the active fracture surface of fill is an inclined plane that does not pass through the heel of the wall, and there are often multiple nearly parallel fracture planes in the fractured body. The active fracture surface of semi-infinite soil is between the movable retaining wall and the fill surface, and the finite soil is between the movable retaining wall and the fixed retaining wall. (2) For the loose finite soil ( λ = 81 %), the upper point of the active fracture surface gradually moves upward from the fixed retaining wall to the fill surface with the increase of the compaction degree of the fill, the active fracture surface gradually becomes steeper, and the finite soil gradually changes into semi-infinite soil. (3) For loose semi-infinite soil ( λ = 81 %), with the increase of compaction degree, the active fracture surface gradually becomes steeper, but the soil between the two walls is still semi-infinite. (4) Under the RB model, the critical width-height ratio of actively destroyed finite soil decreases linearly with the increase of compaction degree. After fitting, the empirical equations of the experimental and simulated values of the critical width-height ratio considering the compaction degree of the fill are given respectively. (5) Under the RB model, the active failure mechanism of fill is similar to the push slide of slope, and the development process of active failure surface is top-down sliding layer by layer. The research in this paper shows that the compaction degree of fill is an important factor affecting the characteristics of the fracture surface and the critical width to height ratio of the finite soil, and it is an important index to define the finite or semi-infinite state of the soil behind the wall.
- 8 January 2025
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 13 (2) , 344-361
Open AccessThe critical width-height ratio of finite soil behind retaining wall considering the compaction degree of fill under RB mode
The compaction degree of fill is an important index for quality control of slope support engineering. Aiming at the influence factor of the compaction degree of fill, the effect of the compaction degree of fill on the characteristics of active fracture surface and the critical width-height ratio of finite soil under the RB model was investigated through laboratory model test and numerical simulation. The primary research findings are as follows: (1) Under RB mode, the active fracture surface of fill is an inclined plane that does not pass through the heel of the wall, and there are often multiple nearly parallel fracture planes in the fractured body. The active fracture surface of semi-infinite soil is between the movable retaining wall and the fill surface, and the finite soil is between the movable retaining wall and the fixed retaining wall. (2) For the loose finite soil ( λ = 81 %), the upper point of the active fracture surface gradually moves upward from the fixed retaining wall to the fill surface with the increase of the compaction degree of the fill, the active fracture surface gradually becomes steeper, and the finite soil gradually changes into semi-infinite soil. (3) For loose semi-infinite soil ( λ = 81 %), with the increase of compaction degree, the active fracture surface gradually becomes steeper, but the soil between the two walls is still semi-infinite. (4) Under the RB model, the critical width-height ratio of actively destroyed finite soil decreases linearly with the increase of compaction degree. After fitting, the empirical equations of the experimental and simulated values of the critical width-height ratio considering the compaction degree of the fill are given respectively. (5) Under the RB model, the active failure mechanism of fill is similar to the push slide of slope, and the development process of active failure surface is top-down sliding layer by layer. The research in this paper shows that the compaction degree of fill is an important factor affecting the characteristics of the fracture surface and the critical width to height ratio of the finite soil, and it is an important index to define the finite or semi-infinite state of the soil behind the wall.
- Open Access
- 15 May 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (5) , e0300586
A case study on soil slope landslide failure and parameter analysis of influencing factors for safety factor based on strength reduction method and orthogonal experimental design
In civil engineering, stability analysis of slope is one of the main content of design. By using the finite element limit analysis software OptumG2, a landslide geological model is established to simulate the failure process of the landslide in Huadu District, Guangzhou City, China. The analysis focused on the deformation and failure characteristics, as well as the mechanical mechanism of landslide; the landslide mode of homogeneous soil is circular sliding. Additionally, investigating the influencing factors affecting slope stability is crucial in engineering implementation; in which the five influencing factors are considered as follow: slope height, slope gradient, soil cohesion, soil internal friction angle, and soil unit weight, respectively. A stability calculation model for a soil slope is established under 25 working conditions based on strength reduction method and orthogonal experimental design, in which the relationship between the safety factor and slope height, slope gradient, soil cohesion, soil internal friction angle, and soil unit weight is obtained. As the slope height increases from 5m to 45m, the safety factor of soil slope gradually decreases from 2.21 to 0.94; As the slope gradient increases from 20° to 60°, the safety factor of soil slope decreases approximately linearly from 1.80 to 0.95; As the cohesion of soil increases from 10kpa to 30kpa, the safety factor of soil slope increases approximately linearly from 1.04 to 1.60; As the internal friction angle of soil increases from 10° to 30°, the safety factor of soil slope increases approximately linearly from 1.00 to 1.81; As the unit weight of soil increases from 13kN/m3 to 21kN/m3, the safety factor of soil slope decreases approximately linearly from 1.50 to 1.21. The influencing factors affecting the safety factor of soil slope in descending order are slope height, slope angle, soil internal friction angle, soil cohesion, and soil unit weight. The research has reference significance for studying the stability and failure laws of soil slopes and conducting landslide control on soil slopes.
- 15 May 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (5) , e0300586
Open AccessA case study on soil slope landslide failure and parameter analysis of influencing factors for safety factor based on strength reduction method and orthogonal experimental design
In civil engineering, stability analysis of slope is one of the main content of design. By using the finite element limit analysis software OptumG2, a landslide geological model is established to simulate the failure process of the landslide in Huadu District, Guangzhou City, China. The analysis focused on the deformation and failure characteristics, as well as the mechanical mechanism of landslide; the landslide mode of homogeneous soil is circular sliding. Additionally, investigating the influencing factors affecting slope stability is crucial in engineering implementation; in which the five influencing factors are considered as follow: slope height, slope gradient, soil cohesion, soil internal friction angle, and soil unit weight, respectively. A stability calculation model for a soil slope is established under 25 working conditions based on strength reduction method and orthogonal experimental design, in which the relationship between the safety factor and slope height, slope gradient, soil cohesion, soil internal friction angle, and soil unit weight is obtained. As the slope height increases from 5m to 45m, the safety factor of soil slope gradually decreases from 2.21 to 0.94; As the slope gradient increases from 20° to 60°, the safety factor of soil slope decreases approximately linearly from 1.80 to 0.95; As the cohesion of soil increases from 10kpa to 30kpa, the safety factor of soil slope increases approximately linearly from 1.04 to 1.60; As the internal friction angle of soil increases from 10° to 30°, the safety factor of soil slope increases approximately linearly from 1.00 to 1.81; As the unit weight of soil increases from 13kN/m3 to 21kN/m3, the safety factor of soil slope decreases approximately linearly from 1.50 to 1.21. The influencing factors affecting the safety factor of soil slope in descending order are slope height, slope angle, soil internal friction angle, soil cohesion, and soil unit weight. The research has reference significance for studying the stability and failure laws of soil slopes and conducting landslide control on soil slopes.
- Open Access
- 8 February 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (2) , e0298337
Study on the failure characteristics of sliding surface and stability analysis of inverted t-type retaining wall in active limit state
This paper investigates the sliding surface failure characteristics, earth pressure distribution law and stability safety factor of inverted T-type retaining wall by using the finite element limit analysis software OptumG2, the effects of width of wall heel plate, width of wall toe plate, thickness of bottom plate, soil–wall interface friction angle, soil cohesion and soil internal friction angle of filling on the failure characteristics of sliding surface, the earth pressure distribution law and stability safety factor of retaining walls are analyzed, The stability safety factor of the retaining wall showed a gradually increasing trend as the width of wall heel plate and wall toe plate increased; as the bottom plate thickness increases, the stability safety factor of the retaining wall gradually increases; as the soil-wall interface element reduction coefficient rises, that is, the internal friction angle of the soil-wall gradually increases to the soil internal friction angle, the stability safety factor of the retaining wall gradually increases; as the soil cohesion and internal friction angle increase, the stability safety factor of the retaining wall progressively increases. The safety factor of retaining wall increases by 0.45 for every 0.5m increase in the width of the wall heel plate; the safety factor of the retaining wall increases by 0.29 when the width of the wall toe plate increases by 0.5m; for every 0.5m increase in the width of wall plate thickness, the safety factor of the retaining wall is increased by 0.62; for every 0.25 increase in soil-wall interface element reduction coefficient, the safety factor of the retaining wall increases by 0.29; for every increase of 5KPa in soil cohesion, the safety factor of the retaining wall increased by 1.16; for every 5° increases in soil internal friction angle, the safety factor of retaining wall increases by 0.6. The research is significant for studying the failure laws and stability of retaining walls and providing references for retaining wall design.
- 8 February 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (2) , e0298337
Open AccessStudy on the failure characteristics of sliding surface and stability analysis of inverted t-type retaining wall in active limit state
This paper investigates the sliding surface failure characteristics, earth pressure distribution law and stability safety factor of inverted T-type retaining wall by using the finite element limit analysis software OptumG2, the effects of width of wall heel plate, width of wall toe plate, thickness of bottom plate, soil–wall interface friction angle, soil cohesion and soil internal friction angle of filling on the failure characteristics of sliding surface, the earth pressure distribution law and stability safety factor of retaining walls are analyzed, The stability safety factor of the retaining wall showed a gradually increasing trend as the width of wall heel plate and wall toe plate increased; as the bottom plate thickness increases, the stability safety factor of the retaining wall gradually increases; as the soil-wall interface element reduction coefficient rises, that is, the internal friction angle of the soil-wall gradually increases to the soil internal friction angle, the stability safety factor of the retaining wall gradually increases; as the soil cohesion and internal friction angle increase, the stability safety factor of the retaining wall progressively increases. The safety factor of retaining wall increases by 0.45 for every 0.5m increase in the width of the wall heel plate; the safety factor of the retaining wall increases by 0.29 when the width of the wall toe plate increases by 0.5m; for every 0.5m increase in the width of wall plate thickness, the safety factor of the retaining wall is increased by 0.62; for every 0.25 increase in soil-wall interface element reduction coefficient, the safety factor of the retaining wall increases by 0.29; for every increase of 5KPa in soil cohesion, the safety factor of the retaining wall increased by 1.16; for every 5° increases in soil internal friction angle, the safety factor of retaining wall increases by 0.6. The research is significant for studying the failure laws and stability of retaining walls and providing references for retaining wall design.
- Open Access
- 1 August 2023
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 11 (3) , 303-326
Non-contact model test and numerical simulation of plastic zone in sandy soil foundation
Reasonable determination of the ultimate bearing capacity of the foundation is of great significance in engineering applications. Based on the self-developed non-contact testing device for the plastic zone of shallow foundation, this paper carries out model test research on the plastic zone of sandy soil shallow foundation and analyzes the development law of plastic zone under the action of foundation load. The main advantages and functional characteristics of the foundation plastic zone test system are that it can realize the non-contact test of displacement deformation of soil, the dynamic development process of shear deformation, and the plastic zone of model foundation can be obtained intuitively. The development process, morphological boundary characteristics, and foundation failure mode of the plastic zone of the sand foundation are obtained. The plastic zone of the foundation starts from the edges of both sides of the bearing plate; with the increase of the load, the plastic zone gradually develops downward and approaches to the center line, and finally crosses through at the bottom until the local shear failure of the foundation occurs. The measured plastic zone is a symmetrical spindle shape with thin ends and a bulge in the middle; the sand on both sides of the bearing plate partially bulges, forming a “V” shaped shear failure zone, and the bottom of bearing plate forms a triangular compression zone, the foundation failure mode of sandy soil represents a typical punching shear failure mode. In order to study the distribution characteristics of the plastic zone range of foundation under different foundation loads and foundation widths, the Universal Distinct Element Code (UDEC) based on the discrete element method is used for numerical simulation research. By conducting parameterized numerical simulation test for the plastic zone of foundation and analyzing the results, with the changes in the foundation load and the foundation width, the variation law of (1) the depth of the plastic zone on the foundation bottom, (2) the width of the plastic zone on both sides of the foundation, (3) the ratio for the depth of plastic zone to the width of foundation, (4) the ratio for the width of plastic zone to the width of foundation and (5) the ratio for the width of plastic zone to the depth of plastic zone is obtained. The research has significant guiding significance for the study of the development law of plastic zone and foundation design.
- 1 August 2023
- Published by JVE International Ltd. in Journal of Measurements in Engineering
- Vol. 11 (3) , 303-326
Open AccessNon-contact model test and numerical simulation of plastic zone in sandy soil foundation
Reasonable determination of the ultimate bearing capacity of the foundation is of great significance in engineering applications. Based on the self-developed non-contact testing device for the plastic zone of shallow foundation, this paper carries out model test research on the plastic zone of sandy soil shallow foundation and analyzes the development law of plastic zone under the action of foundation load. The main advantages and functional characteristics of the foundation plastic zone test system are that it can realize the non-contact test of displacement deformation of soil, the dynamic development process of shear deformation, and the plastic zone of model foundation can be obtained intuitively. The development process, morphological boundary characteristics, and foundation failure mode of the plastic zone of the sand foundation are obtained. The plastic zone of the foundation starts from the edges of both sides of the bearing plate; with the increase of the load, the plastic zone gradually develops downward and approaches to the center line, and finally crosses through at the bottom until the local shear failure of the foundation occurs. The measured plastic zone is a symmetrical spindle shape with thin ends and a bulge in the middle; the sand on both sides of the bearing plate partially bulges, forming a “V” shaped shear failure zone, and the bottom of bearing plate forms a triangular compression zone, the foundation failure mode of sandy soil represents a typical punching shear failure mode. In order to study the distribution characteristics of the plastic zone range of foundation under different foundation loads and foundation widths, the Universal Distinct Element Code (UDEC) based on the discrete element method is used for numerical simulation research. By conducting parameterized numerical simulation test for the plastic zone of foundation and analyzing the results, with the changes in the foundation load and the foundation width, the variation law of (1) the depth of the plastic zone on the foundation bottom, (2) the width of the plastic zone on both sides of the foundation, (3) the ratio for the depth of plastic zone to the width of foundation, (4) the ratio for the width of plastic zone to the width of foundation and (5) the ratio for the width of plastic zone to the depth of plastic zone is obtained. The research has significant guiding significance for the study of the development law of plastic zone and foundation design.
- 15 March 2023
- Published by DAAAM International in International Journal of Simulation Modelling
- Vol. 22 (1) , 145-156
The Plastic Zone of Clay under Foundation Load: an Experimental and Numerical Analysis
- 15 March 2023
- Published by DAAAM International in International Journal of Simulation Modelling
- Vol. 22 (1) , 145-156
The Plastic Zone of Clay under Foundation Load: an Experimental and Numerical Analysis