Tingsong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tingsong Li has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Chen Hu
State Key Laboratory of High Performance Ceramics, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 201899, China
11 shared publications - Jiang Li
Institute of Materiobiology Department of Chemistry College of Sciences Shanghai University Shanghai China
11 shared publications Junlin Wu
Transparent Ceramics Research Center Shanghai Institute of Ceramics Chinese Academy of Sciences Shanghai China
6 shared publicationsQiang Liu
School of Material Science and Engineering Jiangsu University Zhenjiang China
5 shared publicationsDariusz Hreniak
Institute of Low Temperature and Structure Research Polish Academy of Sciences Wroclaw Poland
4 shared publicationsJiang Li
4 shared publications
Latest Publications
- Open Access
Evaluating Thermo-Optical Properties of (Tb0.6Y0.4)3Al5O12 Magneto-Optical Ceramics for High-Power Laser Applications
Mixed (Tb0.6Y0.4)3Al5O12 (TYAG) ceramics with superior optical properties were successfully produced using a solid-state reactive sintering method and subsequent hot isostatic pressing (HIP) treatment. We examined the optical (transmittance and Verdet constant) and thermal-optical characteristics of the ceramics. The prepared TYAG ceramics had an average grain size of ~35 μm and a high in-line transmittance of 83.8@1064 nm. The resulting TYAG ceramics exhibited a Verdet constant of 34 rad/T/m at 1064 nm, which is slightly lower than that of commercial Tb3Ga5O12 crystals (36–40 rad/T/m). We demonstrated that a Faraday isolator based on the TYAG ceramics achieved an isolation ratio of 30 dB with a laser power of 600 W. Using a higher magnetic field of 2.5 T, it is estimated that laser power could increase up to 850 W, without the need for additional adjustments or orientation selection. With its exceptional optical quality and maximum operating power, TYAG transparent ceramics are a promising candidate for use in high-power Faraday isolators.
Open AccessEvaluating Thermo-Optical Properties of (Tb0.6Y0.4)3Al5O12 Magneto-Optical Ceramics for High-Power Laser Applications
Mixed (Tb0.6Y0.4)3Al5O12 (TYAG) ceramics with superior optical properties were successfully produced using a solid-state reactive sintering method and subsequent hot isostatic pressing (HIP) treatment. We examined the optical (transmittance and Verdet constant) and thermal-optical characteristics of the ceramics. The prepared TYAG ceramics had an average grain size of ~35 μm and a high in-line transmittance of 83.8@1064 nm. The resulting TYAG ceramics exhibited a Verdet constant of 34 rad/T/m at 1064 nm, which is slightly lower than that of commercial Tb3Ga5O12 crystals (36–40 rad/T/m). We demonstrated that a Faraday isolator based on the TYAG ceramics achieved an isolation ratio of 30 dB with a laser power of 600 W. Using a higher magnetic field of 2.5 T, it is estimated that laser power could increase up to 850 W, without the need for additional adjustments or orientation selection. With its exceptional optical quality and maximum operating power, TYAG transparent ceramics are a promising candidate for use in high-power Faraday isolators.
- Open Access
- 8 September 2026
- Published by Institute of Central Computation and Knowledge Inc. in Journal of Advanced Materials Research
- Vol. 2 (4) , 262-273
Microstructure and Optical Properties of BaF$_2$ Transparent Ceramics Fabricated by Air Pre-sintering and Hot Isostatic Pressing
BaF$_2$ scintillation ceramics feature a rapid temporal response, high fast-component light yield, and a short X-ray attenuation length, making them a promising material for ultrafast X-ray imaging. In this work, BaF$_2$ nanopowder was co-precipitated from Ba(NO$_3$)$_2$ and KF$\cdot$2H$_2$O, consolidated by 600-750$^{\circ}$C air pre-sintering, and post-treated by hot isostatic pressing (HIP). The ceramics obtained under various process parameters allowed us to investigate temperature-dependent changes in microstructure, transmittance, and scintillation properties, including X-ray-excited luminescence (XEL), decay kinetics, and light yield. It was found that air pre-sintered compacts are porous, with relative density reaching a maximum at 700$^{\circ}$C. In addition, HIP eliminated most of the pores, leaving only residual intragranular pores. Both in-line transmittance and scintillation properties correlated strongly with increasing air pre-sintering temperature. The optimized BaF$_2$ ceramic achieves an in-line transmittance (1mm thick) of 57.6% and 40.6% at 800nm and 220nm, respectively, with a fast component of 16.8% and a light yield of 2655ph/MeV. High-temperature thermoluminescence suggests that a deep trap with considerable intensity may be responsible for the reduced light yield in the ceramic sample.
- 8 September 2026
- Published by Institute of Central Computation and Knowledge Inc. in Journal of Advanced Materials Research
- Vol. 2 (4) , 262-273
Open AccessMicrostructure and Optical Properties of BaF$_2$ Transparent Ceramics Fabricated by Air Pre-sintering and Hot Isostatic Pressing
BaF$_2$ scintillation ceramics feature a rapid temporal response, high fast-component light yield, and a short X-ray attenuation length, making them a promising material for ultrafast X-ray imaging. In this work, BaF$_2$ nanopowder was co-precipitated from Ba(NO$_3$)$_2$ and KF$\cdot$2H$_2$O, consolidated by 600-750$^{\circ}$C air pre-sintering, and post-treated by hot isostatic pressing (HIP). The ceramics obtained under various process parameters allowed us to investigate temperature-dependent changes in microstructure, transmittance, and scintillation properties, including X-ray-excited luminescence (XEL), decay kinetics, and light yield. It was found that air pre-sintered compacts are porous, with relative density reaching a maximum at 700$^{\circ}$C. In addition, HIP eliminated most of the pores, leaving only residual intragranular pores. Both in-line transmittance and scintillation properties correlated strongly with increasing air pre-sintering temperature. The optimized BaF$_2$ ceramic achieves an in-line transmittance (1mm thick) of 57.6% and 40.6% at 800nm and 220nm, respectively, with a fast component of 16.8% and a light yield of 2655ph/MeV. High-temperature thermoluminescence suggests that a deep trap with considerable intensity may be responsible for the reduced light yield in the ceramic sample.
- Open Access
Composite Al2O3-Ce:LuAG Phosphor Ceramics with High Luminous Efficacy and Thermal Conductivity for High-Brightness Laser Lighting
Despite the success of using Al2O3 as a secondary phase in Ce:LuAG phosphor ceramics (PCs), there is still room for improvement in the compositional design of biphasic PCs, as well as in their luminescent and thermal performance. In this study, nanopowders with 40 wt.% Al2O3-0.4at.% Ce:LuAG stoichiometry were synthesized via a co-precipitation approach. Subsequently, a series of compositionally uniform PCs was successfully fabricated by adjusting the vacuum sintering temperature and dwelling time. The grain size distributions of the Al2O3 and LuAG phases, as well as the evolution of porosity and pore size, were systematically analyzed and correlated with the sintering conditions. The addition of Al2O3 has been demonstrated to enhance the thermal properties of ceramics. The thermal conductivity of the “1750 °C × 10 h” sample was 15.6 W·m−1·K−1 at room temperature. Concurrently, it exhibited excellent thermal quenching behavior, retaining 96% of its luminescence intensity upon heating to 450 K. Its fluorescence lifetime was determined to be 21.06 ns. Under 450 nm laser excitation, the optimized PC attained a luminous efficacy of 286 lm·W−1 at 1 W·mm−2. In addition, the luminous flux increased continuously with laser power from 1 to 20 W·mm−2 without any sign of saturation, reaching a maximum of 2500 lm. The findings indicate that biphasic 40 wt.% Al2O3-0.4at.% Ce:LuAG PCs have potential as high-flux, green-color converters for next-generation high-power laser lighting. Furthermore, a laser illumination prototype device incorporating 40 wt.% Al2O3-0.4at.% Ce:LuAG ceramic samples and a 10 W blue laser was constructed. This device emits white light with an illumination range exceeding 500 m, thereby demonstrating its potential applications in laser-driven lighting.
Open AccessComposite Al2O3-Ce:LuAG Phosphor Ceramics with High Luminous Efficacy and Thermal Conductivity for High-Brightness Laser Lighting
Despite the success of using Al2O3 as a secondary phase in Ce:LuAG phosphor ceramics (PCs), there is still room for improvement in the compositional design of biphasic PCs, as well as in their luminescent and thermal performance. In this study, nanopowders with 40 wt.% Al2O3-0.4at.% Ce:LuAG stoichiometry were synthesized via a co-precipitation approach. Subsequently, a series of compositionally uniform PCs was successfully fabricated by adjusting the vacuum sintering temperature and dwelling time. The grain size distributions of the Al2O3 and LuAG phases, as well as the evolution of porosity and pore size, were systematically analyzed and correlated with the sintering conditions. The addition of Al2O3 has been demonstrated to enhance the thermal properties of ceramics. The thermal conductivity of the “1750 °C × 10 h” sample was 15.6 W·m−1·K−1 at room temperature. Concurrently, it exhibited excellent thermal quenching behavior, retaining 96% of its luminescence intensity upon heating to 450 K. Its fluorescence lifetime was determined to be 21.06 ns. Under 450 nm laser excitation, the optimized PC attained a luminous efficacy of 286 lm·W−1 at 1 W·mm−2. In addition, the luminous flux increased continuously with laser power from 1 to 20 W·mm−2 without any sign of saturation, reaching a maximum of 2500 lm. The findings indicate that biphasic 40 wt.% Al2O3-0.4at.% Ce:LuAG PCs have potential as high-flux, green-color converters for next-generation high-power laser lighting. Furthermore, a laser illumination prototype device incorporating 40 wt.% Al2O3-0.4at.% Ce:LuAG ceramic samples and a 10 W blue laser was constructed. This device emits white light with an illumination range exceeding 500 m, thereby demonstrating its potential applications in laser-driven lighting.
- Open Access
- 26 February 2026
- Published by Institute of Central Computation and Knowledge Inc. in Journal of Advanced Materials Research
- Vol. 2 (2) , 86-96
High Luminous Efficacy and Thermal Stability of LuAG:Ce Phosphor Ceramics with Porosity for High-brightness Laser Lighting
The generation of high-brightness white light in laser-illuminated devices is achieved by exciting yellow-green phosphors with a blue laser source. This configuration offers advantages such as high energy density and strong central luminous intensity. Among luminescent materials, LuAG:Ce phosphor ceramics (PCs) are notable for their high thermal stability and luminous output. In this study, LuAG:Ce PCs were produced from co-precipitated monophase nanopowders. The effects of vacuum sintering and air annealing temperatures on their porosity and luminescent properties were investigated. The sample, sintered at 1550°C and subsequently annealed at 1350°C, exhibited 3.5 vol.% porosity, highest room-temperature emission intensity in the series, and retained 96% of that intensity upon heating to 250°C. Under 450 nm laser-diode excitation, the sample achieved a luminous efficacy of 229 lm·W$^{-1}$ while maintaining excellent thermal stability. These results indicate that introducing controlled porosity to act as light-scattering centers in LuAG:Ce ceramics is a viable materials-design strategy for enhancing the luminous performance of laser-driven lighting devices.
- 26 February 2026
- Published by Institute of Central Computation and Knowledge Inc. in Journal of Advanced Materials Research
- Vol. 2 (2) , 86-96
Open AccessHigh Luminous Efficacy and Thermal Stability of LuAG:Ce Phosphor Ceramics with Porosity for High-brightness Laser Lighting
The generation of high-brightness white light in laser-illuminated devices is achieved by exciting yellow-green phosphors with a blue laser source. This configuration offers advantages such as high energy density and strong central luminous intensity. Among luminescent materials, LuAG:Ce phosphor ceramics (PCs) are notable for their high thermal stability and luminous output. In this study, LuAG:Ce PCs were produced from co-precipitated monophase nanopowders. The effects of vacuum sintering and air annealing temperatures on their porosity and luminescent properties were investigated. The sample, sintered at 1550°C and subsequently annealed at 1350°C, exhibited 3.5 vol.% porosity, highest room-temperature emission intensity in the series, and retained 96% of that intensity upon heating to 250°C. Under 450 nm laser-diode excitation, the sample achieved a luminous efficacy of 229 lm·W$^{-1}$ while maintaining excellent thermal stability. These results indicate that introducing controlled porosity to act as light-scattering centers in LuAG:Ce ceramics is a viable materials-design strategy for enhancing the luminous performance of laser-driven lighting devices.
- 20 December 2025
- Published by Institute of Central Computation and Knowledge Inc.
- Vol. 1 (1) , 6-17
Highly Transparent Sm:LuAG Ceramics for Cladding Fabricated by Solid-state Reactive Sintering
In solid-state laser systems with nanosecond repetition rates and high energy, amplified spontaneous emission (ASE) and parasitic oscillation (PO) produced by the gain material can significantly impact the laser output. A well-designed cladding composite structure is an effective solution to absorb ASE and suppress PO. In this work, 5 at.% Sm:LuAG transparent ceramics, a promising cladding material for suppressors of PO at 1064 nm of Nd:LuAG lasers, have been prepared by solid-state reactive sintering at 1825 °C followed by hot isostatic pressing (HIP) post-treatment at 1750 °C. The influences of TEOS (tetraethyl orthosilicate) content on microstructure evolution, in-line transmittance of the 5 at.% Sm:LuAG ceramics were studied. The results show that when the TEOS content is 0.8 wt.%, high transparency Sm:LuAG ceramics can be obtained by vacuum sintering at 1825 °C for 5 h followed by HIP post-treatment at 1750 °C in an argon atmosphere under 200 MPa for 3 h. The optimum in-line transmittance of the HIP-ed Sm:LuAG ceramics (1.5 mm thickness) is 83.3% at a wavelength of 808 nm and absorption coefficient of 3.46 cm$^{-1}$ at 1064 nm, indicating that it can effectively suppress ASE and PO.
- 20 December 2025
- Published by Institute of Central Computation and Knowledge Inc.
- Vol. 1 (1) , 6-17
Highly Transparent Sm:LuAG Ceramics for Cladding Fabricated by Solid-state Reactive Sintering
In solid-state laser systems with nanosecond repetition rates and high energy, amplified spontaneous emission (ASE) and parasitic oscillation (PO) produced by the gain material can significantly impact the laser output. A well-designed cladding composite structure is an effective solution to absorb ASE and suppress PO. In this work, 5 at.% Sm:LuAG transparent ceramics, a promising cladding material for suppressors of PO at 1064 nm of Nd:LuAG lasers, have been prepared by solid-state reactive sintering at 1825 °C followed by hot isostatic pressing (HIP) post-treatment at 1750 °C. The influences of TEOS (tetraethyl orthosilicate) content on microstructure evolution, in-line transmittance of the 5 at.% Sm:LuAG ceramics were studied. The results show that when the TEOS content is 0.8 wt.%, high transparency Sm:LuAG ceramics can be obtained by vacuum sintering at 1825 °C for 5 h followed by HIP post-treatment at 1750 °C in an argon atmosphere under 200 MPa for 3 h. The optimum in-line transmittance of the HIP-ed Sm:LuAG ceramics (1.5 mm thickness) is 83.3% at a wavelength of 808 nm and absorption coefficient of 3.46 cm$^{-1}$ at 1064 nm, indicating that it can effectively suppress ASE and PO.
- 10 April 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (19) , 29088-29097
Co-precipitation synthesis and sintering of 4.5 at.% Sm:YAG nano-powders for cladding ceramics
- 10 April 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (19) , 29088-29097
Co-precipitation synthesis and sintering of 4.5 at.% Sm:YAG nano-powders for cladding ceramics
- 4 March 2025
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (7)
Scintillation properties and slow component suppression mechanism of BaF 2 transparent ceramics
BaF 2 nano‐powders with the average particle size of 148 nm were synthesized by the coprecipitation method. Then, BaF 2 transparent ceramics were successfully fabricated by hot pressing (HP) combined with hot isostatic pressing (HIP). The BaF 2 transparent ceramics with the thickness of 2 mm exhibited an in‐line transmittance of 42.9% at 800 nm. In addition, the scintillation performance of the BaF 2 transparent ceramics was systematically studied. The XEL (X‐ray excited luminescence) spectra and scintillation decay curves demonstrate that the slow components in the BaF 2 ceramics are effectively suppressed compared with that in single crystal, and the fast component of undoped BaF 2 ceramics reaches 21.2% with a light yield of 5973 ph/MeV. To further investigate the mechanism of slow component suppression in BaF 2 ceramics, the temperature‐dependent XEL spectra and low‐temperature TSL (thermal stimulated luminescence) curves were also investigated. The results demonstrate that there may be faster quenching centers within the ceramics that quench STE (Self‐trapping exciton), and the intensity of the first TSL peak was reduced compared to that of crystals, thus leading to a decrease in the percentage of slow component of BaF 2 ceramics.
- 4 March 2025
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (7)
Scintillation properties and slow component suppression mechanism of BaF 2 transparent ceramics
BaF 2 nano‐powders with the average particle size of 148 nm were synthesized by the coprecipitation method. Then, BaF 2 transparent ceramics were successfully fabricated by hot pressing (HP) combined with hot isostatic pressing (HIP). The BaF 2 transparent ceramics with the thickness of 2 mm exhibited an in‐line transmittance of 42.9% at 800 nm. In addition, the scintillation performance of the BaF 2 transparent ceramics was systematically studied. The XEL (X‐ray excited luminescence) spectra and scintillation decay curves demonstrate that the slow components in the BaF 2 ceramics are effectively suppressed compared with that in single crystal, and the fast component of undoped BaF 2 ceramics reaches 21.2% with a light yield of 5973 ph/MeV. To further investigate the mechanism of slow component suppression in BaF 2 ceramics, the temperature‐dependent XEL spectra and low‐temperature TSL (thermal stimulated luminescence) curves were also investigated. The results demonstrate that there may be faster quenching centers within the ceramics that quench STE (Self‐trapping exciton), and the intensity of the first TSL peak was reduced compared to that of crystals, thus leading to a decrease in the percentage of slow component of BaF 2 ceramics.
- 25 February 2025
- Published by Elsevier in Optical Materials
- Vol. 162
Influence of annealing temperatures on the properties of Gd2O2S:Tb scintillation ceramics for neutron imaging
- 25 February 2025
- Published by Elsevier in Optical Materials
- Vol. 162
Influence of annealing temperatures on the properties of Gd2O2S:Tb scintillation ceramics for neutron imaging
- 26 December 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (4)
Influence of vacuum pre‐sintering temperature on the Eu 2+ –Dy 3+ co‐doped SrAl 2 O 4 ceramics with persistent luminescence
(Sr 0.97 Eu 0.01 Dy 0.02 )Al 2 O 4 persistent luminescence (PersL) ceramics were fabricated by solid‐state reactive pre‐sintering in vacuum combined with hot isostatic pressing (HIP) post‐treatment adding H 3 BO 3 as a sintering additive. The influence of pre‐sintering temperature on the phase composition, microstructure, and PersL performance of (Sr 0.97 Eu 0.01 Dy 0.02 )Al 2 O 4 ceramics was investigated. The results showed that optimum persistent performance was obtained by the ceramics prepared by vacuum pre‐sintered at 1600°C for 3 h and HIP post‐treated at 1400°C for 3 h under 200 MPa in Ar. The persistent initial luminescence intensity exceeded 9200 mcd/m 2 after 5 min when the optimum sample was simulated by the daylight irradiation of 1000 lx, and the persistent emission decay time was longer than 14 h. The trap depth was calculated using two methods, and the results showed that the ceramics prepared at pre‐sintering temperature of 1600°C had the highest trap depth.
- 26 December 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (4)
Influence of vacuum pre‐sintering temperature on the Eu 2+ –Dy 3+ co‐doped SrAl 2 O 4 ceramics with persistent luminescence
(Sr 0.97 Eu 0.01 Dy 0.02 )Al 2 O 4 persistent luminescence (PersL) ceramics were fabricated by solid‐state reactive pre‐sintering in vacuum combined with hot isostatic pressing (HIP) post‐treatment adding H 3 BO 3 as a sintering additive. The influence of pre‐sintering temperature on the phase composition, microstructure, and PersL performance of (Sr 0.97 Eu 0.01 Dy 0.02 )Al 2 O 4 ceramics was investigated. The results showed that optimum persistent performance was obtained by the ceramics prepared by vacuum pre‐sintered at 1600°C for 3 h and HIP post‐treated at 1400°C for 3 h under 200 MPa in Ar. The persistent initial luminescence intensity exceeded 9200 mcd/m 2 after 5 min when the optimum sample was simulated by the daylight irradiation of 1000 lx, and the persistent emission decay time was longer than 14 h. The trap depth was calculated using two methods, and the results showed that the ceramics prepared at pre‐sintering temperature of 1600°C had the highest trap depth.