Stephen R. Ross
Research Subjects
Stephen R. Ross has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Joyeeta Nag
Non-Volatile Memory Research, Western Digital 2 , San Jose, California 95119
3 shared publications - Kartik Sondhi
Silicon Technology & Manufacturing, Western Digital 1 , Milpitas, California 95035
3 shared publications - Senaka Kanakamedala
Silicon Technology & Manufacturing, Western Digital 1 , Milpitas, California 95035
3 shared publications - Aaron N. Fancher
New Non-Volatile Memory Research, Western Digital 2 , San Jose, California 95119
2 shared publications Alexei L. Bogdanov
New Non-Volatile Memory Research, Western Digital 2 , San Jose, California 95119
2 shared publications- Mark D. Kraman
Sandisk Technologies, Inc., Milpitas, USA
2 shared publications
Latest Publications
- 2 August 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (5)
Inherent area selective deposition of silicon dioxide in multilayer 3D SiOx–SiNx stacks
Device scaling for future semiconductor technologies is driving the adoption of innovative methods for miniaturizing semiconductor chips. One promising approach that has garnered significant interest for sub-10 nm device scaling is area selective deposition (ASD). In this study, we demonstrate the feasibility of ASD of silicon dioxide (SiO2) on –OH terminated surfaces (silicon oxide: SiOx) but not on –NH terminated surfaces (silicon nitride: SiNx) for 2D blanket, 2D patterned, and 3D stacks using a novel precursor: Orthrus. To achieve this, we optimized the SiOx and SiNx layers to enhance the –OH and –NH surface bonds, respectively. Using x-ray photo spectroscopy analysis, we showed that SiO2 selectively deposits on SiOx without any nucleation delay compared to SiNx. We have demonstrated the inherent selective deposition of approximately ∼4 nm on 2D patterned structures and ∼3.7 nm on 3D stacks by fine-tuning the atomic layer deposition process. This selective thickness is >250% compared to a previously shown selective SiO2 deposition process in the literature. Finally, we also showed that the step coverage of selective SiO2 growth in 3D stacks is ∼1. This study highlights the potential pathway for performing ASD of commonly used SiO2 in 3D high-aspect-ratio stacks.
- 2 August 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (5)
Inherent area selective deposition of silicon dioxide in multilayer 3D SiOx–SiNx stacks
Device scaling for future semiconductor technologies is driving the adoption of innovative methods for miniaturizing semiconductor chips. One promising approach that has garnered significant interest for sub-10 nm device scaling is area selective deposition (ASD). In this study, we demonstrate the feasibility of ASD of silicon dioxide (SiO2) on –OH terminated surfaces (silicon oxide: SiOx) but not on –NH terminated surfaces (silicon nitride: SiNx) for 2D blanket, 2D patterned, and 3D stacks using a novel precursor: Orthrus. To achieve this, we optimized the SiOx and SiNx layers to enhance the –OH and –NH surface bonds, respectively. Using x-ray photo spectroscopy analysis, we showed that SiO2 selectively deposits on SiOx without any nucleation delay compared to SiNx. We have demonstrated the inherent selective deposition of approximately ∼4 nm on 2D patterned structures and ∼3.7 nm on 3D stacks by fine-tuning the atomic layer deposition process. This selective thickness is >250% compared to a previously shown selective SiO2 deposition process in the literature. Finally, we also showed that the step coverage of selective SiO2 growth in 3D stacks is ∼1. This study highlights the potential pathway for performing ASD of commonly used SiO2 in 3D high-aspect-ratio stacks.
- Open Access
- 15 November 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (6)
Understanding 3D anisotropic reactive ion etching of oxide-metal stacks
Scaling semiconductor devices necessitates the fabrication of high-aspect-ratio narrow features through the precise etching of multiple layers comprising alternating materials, each with sub-20 nm thickness. However, etching dissimilar materials, such as alternating metal and oxide layers, pose significant challenges due to inherent discrepancies in vertical and lateral etch rates. This study demonstrates the feasibility of etching a stack comprising 10 layers of silicon dioxide (SiO2) and molybdenum (Mo) using an Oxford Instruments ICP RIE tool operating at a low power regime (bias < 250 V). We evaluated different etch chemistries, including Cl2/CHF3 and CF4/CHF3, and the role of CH4 as a passivation gas to control the lateral etch rates. Mask encapsulation with Ru was employed to protect the hardmask during the etching process, enabling successful etching of 10 layers without lateral recess. Experimental results were validated using Sentaurus™ TCAD software to investigate the impact of gas chemistry on the stack etch rate. Our findings provide valuable insights into the performance of various etch chemistries, demonstrating the effectiveness of the evaluated chemistries and the role of CH4 in improving profile characteristics. The integration of experimental and computational approaches facilitates the optimization of process parameters for advanced integrated circuit fabrication.
- 15 November 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (6)
Open AccessUnderstanding 3D anisotropic reactive ion etching of oxide-metal stacks
Scaling semiconductor devices necessitates the fabrication of high-aspect-ratio narrow features through the precise etching of multiple layers comprising alternating materials, each with sub-20 nm thickness. However, etching dissimilar materials, such as alternating metal and oxide layers, pose significant challenges due to inherent discrepancies in vertical and lateral etch rates. This study demonstrates the feasibility of etching a stack comprising 10 layers of silicon dioxide (SiO2) and molybdenum (Mo) using an Oxford Instruments ICP RIE tool operating at a low power regime (bias < 250 V). We evaluated different etch chemistries, including Cl2/CHF3 and CF4/CHF3, and the role of CH4 as a passivation gas to control the lateral etch rates. Mask encapsulation with Ru was employed to protect the hardmask during the etching process, enabling successful etching of 10 layers without lateral recess. Experimental results were validated using Sentaurus™ TCAD software to investigate the impact of gas chemistry on the stack etch rate. Our findings provide valuable insights into the performance of various etch chemistries, demonstrating the effectiveness of the evaluated chemistries and the role of CH4 in improving profile characteristics. The integration of experimental and computational approaches facilitates the optimization of process parameters for advanced integrated circuit fabrication.
- Open Access
- 8 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (4)
Hardmask engineering by mask encapsulation for enabling next generation reactive ion etch scaling
Miniaturization and scaling of semiconductor devices require development of innovative techniques to sustain advancements. A promising trend is the migration from 2D to 3D device architectures that necessitate fabrication of high-aspect-ratio narrow features through layers of different materials. Reactive ion etching can achieve this but poses unique challenges due to the requirement of etch chemistries capable of etching dissimilar materials with varying etch rates while maintaining high productivity. The choice of hardmask is also crucial, as it plays a critical role in determining efficacy of the etch process and the final shape of the feature being etched. To address these challenges, we introduce a new concept of hardmask engineering that involves a bilayer hardmask scheme consisting of a patterned conventional hardmask encapsulated with a thin layer of etch-resistant ruthenium (Ru) layer. Experimental results for etching multilayer stacks consisting of alternating pairs of SiO2 and Mo show that this engineered hardmask results in improved hardmask remaining and etch profile with smaller critical dimensions (CDs). Technology computer-aided design simulations with the Ru encapsulation layer on conventional carbon hardmask demonstrate increased poly-Si etch depth with reduced bow CD. This concept can be extended to any semiconductor nanofabrication step involving high-aspect-ratio etching where precise control of CDs is essential in the vertical direction.
- 8 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (4)
Open AccessHardmask engineering by mask encapsulation for enabling next generation reactive ion etch scaling
Miniaturization and scaling of semiconductor devices require development of innovative techniques to sustain advancements. A promising trend is the migration from 2D to 3D device architectures that necessitate fabrication of high-aspect-ratio narrow features through layers of different materials. Reactive ion etching can achieve this but poses unique challenges due to the requirement of etch chemistries capable of etching dissimilar materials with varying etch rates while maintaining high productivity. The choice of hardmask is also crucial, as it plays a critical role in determining efficacy of the etch process and the final shape of the feature being etched. To address these challenges, we introduce a new concept of hardmask engineering that involves a bilayer hardmask scheme consisting of a patterned conventional hardmask encapsulated with a thin layer of etch-resistant ruthenium (Ru) layer. Experimental results for etching multilayer stacks consisting of alternating pairs of SiO2 and Mo show that this engineered hardmask results in improved hardmask remaining and etch profile with smaller critical dimensions (CDs). Technology computer-aided design simulations with the Ru encapsulation layer on conventional carbon hardmask demonstrate increased poly-Si etch depth with reduced bow CD. This concept can be extended to any semiconductor nanofabrication step involving high-aspect-ratio etching where precise control of CDs is essential in the vertical direction.