Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lei Qiao has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Annealing Temperature on Microstructure and Corrosion Resistance of HVOF-Sprayed Fe-Based Amorphous–Nanocrystalline Coatings

    by Lei Qiao, Xiaoqiang Zhang, Taotao Li, Ruifeng Li

    In this work, a Fe-based amorphous coating (Fe44Cr18Mo7Ni4Cu2B20Si3C2) was fabricated via high-velocity oxygen fuel (HVOF) spraying, and the effect of annealing temperature on its microstructure, phase composition, and corrosion resistance in 3.5 wt.% NaCl solution was investigated. The as-sprayed (AS) coating exhibits an amorphous content of 85.71% and a porosity of 1.37%. Annealing at 540 °C (H540) reduces porosity to 0.98% without significant crystallization, whereas annealing at 640 °C (H640) and 740 °C (H740) triggers extensive crystallization (amorphous content drops to 24.18% and 19.20%), and porosity increases to 1.82% and 2.17%. Electrochemical tests show that corrosion resistance deteriorates progressively with increasing temperature. icorr increases from 3.56 μA/cm2 (AS) to 50.0 μA/cm2 (H740), while Rp decreases from 8472 to 669 Ω·cm2. EIS reveals that the AS coating is dominated by the inner barrier layer (Rb >> Rt), whereas annealing causes a drastic collapse of Rb (from 8.374 × 104 to 5.011 Ω·cm2). This degradation is attributed to crystallization-induced grain boundaries and reduced effective Cr content, which impair passive film integrity and accelerate corrosion.

  • Open Access

    Effects of Sliding Speed on Wear Behavior of High-Velocity Oxygen Fuel-Sprayed FeCrMoNiCuBSiC Metallic Glass Coatings

    by Lei Qiao, Botao Zhou, Ruifeng Li, Taotao Li, Yue Zhao, Xiaoqiang Zhang, Chul-Hee Lee

    A FeCrMoNiCuBSiC metallic glass coating was designed and then deposited by the high-velocity oxygen fuel (HVOF) spraying technique. X-ray diffraction, a scanning electron microscope, and a microhardness tester were applied to characterize the phase, microstructure, and mechanical properties of the coating. The amorphous phase was the main phase in the coating, and crystal phases were almost undetectable in the XRD results. The coating had a dense structure (the porosity was 1.47 ± 0.32%) and high Vickers microhardness (848 ± 22 HV0.3). The wear behavior of the coatings sliding against WC-Co was studied with a pin-on-disc wear test system and was compared with that of 316L stainless steel. The coating improved the wear resistance of the steel by around 7–9 times at different sliding speeds. As the sliding speed was increased, the wear loss rate of the steel obviously increased, yet the loss rate of the coating decreased first and then increased. This happened because the contact flash temperature induced by friction increases with the sliding speed, which results in oxidative behavior and crystallization events in the coating. The dominating wear mechanism of the coating is fatigue wear combined with oxidative wear.


  • Open Access

    A Comprehensive Study on Microstructure and Wear Behavior of Nano-WC Reinforced Ni60 Laser Coating on 17-4PH Stainless Steel

    by Jie Wang, Xiaoqiang Zhang, Lei Qiao, Yue Zhao, Mengfei Ren, Tiaotiao Li, Ruifeng Li

    The surface of 17-4PH martensitic stainless steel was laser-cladded with Ni60 and Ni60+nano-WC composites and a comprehensive investigation was conducted of the microstructure and wear mechanism. The findings demonstrate that despite the added nano-WC particles being fused and dissolved during laser cladding, they still lead to a reduction in grain size and a decrease in crystallographic orientation strength. Furthermore, the dissolution of nano-WC makes the lamellar M23C6 carbides transform into a rod or block morphology, and leads to the CrB borides becoming finer and more evenly dispersed. This microstructural evolution resulted in a uniform increase in hardness and wear resistance, effectively preventing crack formation. When the nano-WC addition increased to 20 wt.%, there was a 27.12% increase in microhardness and an 85.19% decrease in volume wear rate compared to that of the pure Ni60 coating. Through analysis of the microstructure and topography of wear traces, it can be inferred that as the nano-WC addition increased from 0 wt.% up to 20 wt.%, there was a gradual transition from two-body abrasive wear to three-body abrasive wear, ultimately resulting in adherent wear.