Minghua Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Minghua Chen has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Fufa Wu
School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, China
5 shared publicationsKe Li
School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, China
3 shared publicationsRuiqiang Xu
Liaoning University of Technology, Jinzhou, China
3 shared publicationsChenbin Li
Beijing Xinghang Electro-mechanical Equipment Co. Ltd., Beijing, People’s Republic of China
2 shared publicationsLiang Liu
School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, People's Republic of China
2 shared publications- Lijun Xin
School of Mechanical and Electrical Engineering, Tangshan University, Tangshan, China
2 shared publications
Latest Publications
- 1 June 2024
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 29 (4) , 261-270
Study on the crystallisation of amorphous alloy–titanium alloy joints during different welding processes
In this study, continuous laser beam welding (CLBW) and tungsten-inert-gas (TIG) welding were employed to weld β-Ti dendrite-toughened metal glass composite with TC4 titanium alloy. The microstructure, element distribution, and mechanical properties of the welded joints were studied. The influence of the welding heat source state and welding speed on the crystallisation of the joints was analysed. The results revealed that at the interface between the fusion zone (FZ) and the Ti alloy, columnar crystals of β-Ti grew positively and extended from the Ti alloy into the FZ. The development of β-Ti grains was more pronounced during TIG welding than during CLBW owing to the lower cooling rate of the liquid pool in TIG welding. The hardness in the FZ of the TIG-welded sample was lower than that of the CLBW sample.
- 1 June 2024
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 29 (4) , 261-270
Study on the crystallisation of amorphous alloy–titanium alloy joints during different welding processes
In this study, continuous laser beam welding (CLBW) and tungsten-inert-gas (TIG) welding were employed to weld β-Ti dendrite-toughened metal glass composite with TC4 titanium alloy. The microstructure, element distribution, and mechanical properties of the welded joints were studied. The influence of the welding heat source state and welding speed on the crystallisation of the joints was analysed. The results revealed that at the interface between the fusion zone (FZ) and the Ti alloy, columnar crystals of β-Ti grew positively and extended from the Ti alloy into the FZ. The development of β-Ti grains was more pronounced during TIG welding than during CLBW owing to the lower cooling rate of the liquid pool in TIG welding. The hardness in the FZ of the TIG-welded sample was lower than that of the CLBW sample.
- 25 January 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (3) , 2046-2051
Microstructure and Mechanical Properties of Ti-Based Amorphous Solder Vacuum Brazing Joint for Stainless Steel
- 25 January 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (3) , 2046-2051
Microstructure and Mechanical Properties of Ti-Based Amorphous Solder Vacuum Brazing Joint for Stainless Steel
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240770
Microstructures and mechanical properties of laser brazed TC4 titanium alloy joint using internal dendrite amorphous alloy as the filler metal
The laser brazing technology for TC4 titanium alloy using a Ti-based amorphous alloy as brazing filler metal was studied. Results show that laser brazing of TC4 titanium alloy can be achieved by using a Ti-based amorphous alloy, and a continuous and stable brazed joint without welding defects can be obtained. The microstructure comprises broken β-Ti dendrites dispersed on the amorphous alloy matrix, and columnar crystals are formed on both sides near the interface of the base metal. In the brazing process, the Zr element in the liquid filler metal diffuses to the TC4 base metal at a depth of about 50 μm. The hardness of the brazed zone is about 540 HV, which is much higher than that of the base metal at 320 HV. The tensile strength of brazed joint is about 960 MPa, and the specimen fractured on TC4 base metal.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240770
Open AccessMicrostructures and mechanical properties of laser brazed TC4 titanium alloy joint using internal dendrite amorphous alloy as the filler metal
The laser brazing technology for TC4 titanium alloy using a Ti-based amorphous alloy as brazing filler metal was studied. Results show that laser brazing of TC4 titanium alloy can be achieved by using a Ti-based amorphous alloy, and a continuous and stable brazed joint without welding defects can be obtained. The microstructure comprises broken β-Ti dendrites dispersed on the amorphous alloy matrix, and columnar crystals are formed on both sides near the interface of the base metal. In the brazing process, the Zr element in the liquid filler metal diffuses to the TC4 base metal at a depth of about 50 μm. The hardness of the brazed zone is about 540 HV, which is much higher than that of the base metal at 320 HV. The tensile strength of brazed joint is about 960 MPa, and the specimen fractured on TC4 base metal.
- 26 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (8) , 2252-2259
Analysis on TIG Arc During Welding of Magnesium Alloy Sheet by a Combination of Spectral Diagnosing and Langmuir Probe Detection
To identify the discharge features of tungsten inert gas (TIG) welding arc on magnesium alloy workpiece, spectral diagnosing and a self-developed Langmuir probe detection were jointly performed on the welding arc. Results show that during welding, Mg atoms with low ionization energy rush into the burning arc and replace Ar atoms to discharge, which gives influences on arc discharge. The arc plasmas have a normal space potential distribution. Reflected by both of the two diagnosing methods, region near arc anode (magnesium alloy workpiece) has the lowest electron temperature and the highest electron density. The variations of electron temperature and density with the position have similar trends measured by the two diagnosing methods, indicating that the self-developed probe detection system is effective and reliable in diagnosing the welding arc. It is also found that the diagnosing error of probe detection is a little larger than that of spectral diagnosing, especially in the region near cathode. This research gives a new method to diagnose the welding arc, and the results can give experimental indication and support to researchers in arc welding area from another view sight.
- 26 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (8) , 2252-2259
Analysis on TIG Arc During Welding of Magnesium Alloy Sheet by a Combination of Spectral Diagnosing and Langmuir Probe Detection
To identify the discharge features of tungsten inert gas (TIG) welding arc on magnesium alloy workpiece, spectral diagnosing and a self-developed Langmuir probe detection were jointly performed on the welding arc. Results show that during welding, Mg atoms with low ionization energy rush into the burning arc and replace Ar atoms to discharge, which gives influences on arc discharge. The arc plasmas have a normal space potential distribution. Reflected by both of the two diagnosing methods, region near arc anode (magnesium alloy workpiece) has the lowest electron temperature and the highest electron density. The variations of electron temperature and density with the position have similar trends measured by the two diagnosing methods, indicating that the self-developed probe detection system is effective and reliable in diagnosing the welding arc. It is also found that the diagnosing error of probe detection is a little larger than that of spectral diagnosing, especially in the region near cathode. This research gives a new method to diagnose the welding arc, and the results can give experimental indication and support to researchers in arc welding area from another view sight.
- 15 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (7) , 2004-2009
Identification of Ionization Region Profile and Potential Distribution in Welding Arc Plasma by Direct Probe Detection
A special probe detection system and analyzing method were designed for estimating the ionization region in welding arc. Results showed that ionization region in gas tungsten welding arc is in spindle shape. Arc plasma prefers to contract near anode workpiece. The arc volume increases with the increase of welding arc current accordingly. With the decrease of arc length, the arc expands in radius direction. Electrical equipotential lines nearly parallel the anode surface and tend to bend to the tungsten electrode in the region near cathode. Voltage drop near the cathode dominates the arc voltage when arc current changes.
- 15 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (7) , 2004-2009
Identification of Ionization Region Profile and Potential Distribution in Welding Arc Plasma by Direct Probe Detection
A special probe detection system and analyzing method were designed for estimating the ionization region in welding arc. Results showed that ionization region in gas tungsten welding arc is in spindle shape. Arc plasma prefers to contract near anode workpiece. The arc volume increases with the increase of welding arc current accordingly. With the decrease of arc length, the arc expands in radius direction. Electrical equipotential lines nearly parallel the anode surface and tend to bend to the tungsten electrode in the region near cathode. Voltage drop near the cathode dominates the arc voltage when arc current changes.
- 1 August 2022
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 27 (6) , 463-471
Butt welding of TiZrMoCuBe MGC/TC4 titanium alloy using a pulsed Nd:YAG laser
β-Ti dendrite toughened metal glass composite and TC4 titanium alloy were butt welded by a pulsed laser. Microstructures and mechanical properties of the welded joint were specially studied. Results show that microstructure in the fusion zone is uneven, and mainly consists of dendritical β-Ti grains (in nanometre or micron scales) and amorphous alloy background. Special chemical compositions of base materials, shocking effect from laser pulses and large cooling speed during welding directly restrain the development of crystal β-Ti grain in the fusion zone. Hardness in the fusion zone ranges from 500 HV to more than 600 HV. During tensile tests, all the welded joints fracture on TC4 titanium alloy base material side.
- 1 August 2022
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 27 (6) , 463-471
Butt welding of TiZrMoCuBe MGC/TC4 titanium alloy using a pulsed Nd:YAG laser
β-Ti dendrite toughened metal glass composite and TC4 titanium alloy were butt welded by a pulsed laser. Microstructures and mechanical properties of the welded joint were specially studied. Results show that microstructure in the fusion zone is uneven, and mainly consists of dendritical β-Ti grains (in nanometre or micron scales) and amorphous alloy background. Special chemical compositions of base materials, shocking effect from laser pulses and large cooling speed during welding directly restrain the development of crystal β-Ti grain in the fusion zone. Hardness in the fusion zone ranges from 500 HV to more than 600 HV. During tensile tests, all the welded joints fracture on TC4 titanium alloy base material side.
- 28 February 2021
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 26 (3) , 264-272
Influence of laser pulse on solidification of molten pool during laser welding of dissimilar Ti-based amorphous alloys
Dissimilar Ti-based amorphous alloy sheets were butt welded by a pulsed laser and metallurgical joints were obtained. The β-Ti crystal grains in nanometre scale unevenly distribute on the amorphous background in the fusion zone. With the increase of laser pulse energy and pulse duration, the crystalline β-Ti grains grow up from spherical to dendritical profile, but the crystalline size reaches its maximum of about 1 µm, which is much smaller than the grains in base metal. The refinement of the grains in fusion zone results from the fast cooling speed during welding. The microhardness in the welded joints ranges from 470 to 525 HV. Average tensile strength of the welded joint is about 1510 MPa (86% of pure Ti-based amorphous alloy BM and 91% of β-Ti dendrite reinforced Ti-based amorphous alloy BM).
- 28 February 2021
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 26 (3) , 264-272
Influence of laser pulse on solidification of molten pool during laser welding of dissimilar Ti-based amorphous alloys
Dissimilar Ti-based amorphous alloy sheets were butt welded by a pulsed laser and metallurgical joints were obtained. The β-Ti crystal grains in nanometre scale unevenly distribute on the amorphous background in the fusion zone. With the increase of laser pulse energy and pulse duration, the crystalline β-Ti grains grow up from spherical to dendritical profile, but the crystalline size reaches its maximum of about 1 µm, which is much smaller than the grains in base metal. The refinement of the grains in fusion zone results from the fast cooling speed during welding. The microhardness in the welded joints ranges from 470 to 525 HV. Average tensile strength of the welded joint is about 1510 MPa (86% of pure Ti-based amorphous alloy BM and 91% of β-Ti dendrite reinforced Ti-based amorphous alloy BM).
- 17 July 2014
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 75 (1-4) , 331-337
A new superimposed double-arc welding method with one arc submerged in the weld pool
- 17 July 2014
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 75 (1-4) , 331-337
A new superimposed double-arc welding method with one arc submerged in the weld pool