Lijun Xin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lijun Xin has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Fufa Wu
School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, China
5 shared publicationsMinghua Chen
3 shared publicationsKe Li
School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, China
2 shared publications- Minghua Chen
School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, China
2 shared publications Qi Zhou
2 shared publicationsChenbin Li
1 shared publication
Latest Publications
- 1 June 2024
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 29 (4) , 261-270
Study on the crystallisation of amorphous alloy–titanium alloy joints during different welding processes
In this study, continuous laser beam welding (CLBW) and tungsten-inert-gas (TIG) welding were employed to weld β-Ti dendrite-toughened metal glass composite with TC4 titanium alloy. The microstructure, element distribution, and mechanical properties of the welded joints were studied. The influence of the welding heat source state and welding speed on the crystallisation of the joints was analysed. The results revealed that at the interface between the fusion zone (FZ) and the Ti alloy, columnar crystals of β-Ti grew positively and extended from the Ti alloy into the FZ. The development of β-Ti grains was more pronounced during TIG welding than during CLBW owing to the lower cooling rate of the liquid pool in TIG welding. The hardness in the FZ of the TIG-welded sample was lower than that of the CLBW sample.
- 1 June 2024
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 29 (4) , 261-270
Study on the crystallisation of amorphous alloy–titanium alloy joints during different welding processes
In this study, continuous laser beam welding (CLBW) and tungsten-inert-gas (TIG) welding were employed to weld β-Ti dendrite-toughened metal glass composite with TC4 titanium alloy. The microstructure, element distribution, and mechanical properties of the welded joints were studied. The influence of the welding heat source state and welding speed on the crystallisation of the joints was analysed. The results revealed that at the interface between the fusion zone (FZ) and the Ti alloy, columnar crystals of β-Ti grew positively and extended from the Ti alloy into the FZ. The development of β-Ti grains was more pronounced during TIG welding than during CLBW owing to the lower cooling rate of the liquid pool in TIG welding. The hardness in the FZ of the TIG-welded sample was lower than that of the CLBW sample.
- 26 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (8) , 2252-2259
Analysis on TIG Arc During Welding of Magnesium Alloy Sheet by a Combination of Spectral Diagnosing and Langmuir Probe Detection
To identify the discharge features of tungsten inert gas (TIG) welding arc on magnesium alloy workpiece, spectral diagnosing and a self-developed Langmuir probe detection were jointly performed on the welding arc. Results show that during welding, Mg atoms with low ionization energy rush into the burning arc and replace Ar atoms to discharge, which gives influences on arc discharge. The arc plasmas have a normal space potential distribution. Reflected by both of the two diagnosing methods, region near arc anode (magnesium alloy workpiece) has the lowest electron temperature and the highest electron density. The variations of electron temperature and density with the position have similar trends measured by the two diagnosing methods, indicating that the self-developed probe detection system is effective and reliable in diagnosing the welding arc. It is also found that the diagnosing error of probe detection is a little larger than that of spectral diagnosing, especially in the region near cathode. This research gives a new method to diagnose the welding arc, and the results can give experimental indication and support to researchers in arc welding area from another view sight.
- 26 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (8) , 2252-2259
Analysis on TIG Arc During Welding of Magnesium Alloy Sheet by a Combination of Spectral Diagnosing and Langmuir Probe Detection
To identify the discharge features of tungsten inert gas (TIG) welding arc on magnesium alloy workpiece, spectral diagnosing and a self-developed Langmuir probe detection were jointly performed on the welding arc. Results show that during welding, Mg atoms with low ionization energy rush into the burning arc and replace Ar atoms to discharge, which gives influences on arc discharge. The arc plasmas have a normal space potential distribution. Reflected by both of the two diagnosing methods, region near arc anode (magnesium alloy workpiece) has the lowest electron temperature and the highest electron density. The variations of electron temperature and density with the position have similar trends measured by the two diagnosing methods, indicating that the self-developed probe detection system is effective and reliable in diagnosing the welding arc. It is also found that the diagnosing error of probe detection is a little larger than that of spectral diagnosing, especially in the region near cathode. This research gives a new method to diagnose the welding arc, and the results can give experimental indication and support to researchers in arc welding area from another view sight.
- 1 November 2020
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 134
Microstructures of the pulsed laser welded TiZrBeCuMo composite amorphous alloy joint
- 1 November 2020
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 134
Microstructures of the pulsed laser welded TiZrBeCuMo composite amorphous alloy joint
- 1 January 2018
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 100, 208-215
Effect of laser pulse on alternative current arc discharge during laser-arc hybrid welding of magnesium alloy
- 1 January 2018
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 100, 208-215
Effect of laser pulse on alternative current arc discharge during laser-arc hybrid welding of magnesium alloy
- 1 October 2016
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 85, 1-8
Comparative study on interactions between laser and arc plasma during laser-GTA welding and laser-GMA welding
- 1 October 2016
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 85, 1-8
Comparative study on interactions between laser and arc plasma during laser-GTA welding and laser-GMA welding
- 1 January 2009
- Published by Laser Institute of America
- Vol. 2009 (1) , 1569-1572
Comparative study on the application of fiber laser and slab CO2 laser in welding DP780 high strength steel plate
Welding experiments of high strength steel plate produced by Baosteel with IPG YLR-6000-ST2 fiber laser and Slab CO2 laser have been processed. The differences of laser in practical application have been investigated through the contrast of parameters and welding seam dynamic performances. It is showed that the maximum welding speed of fiber laser is 2∼3 times faster than Slab CO2 laser; the welding speed of fiber laser with the power 1300W is as same as Slab CO2 laser 3500W; the samples prepared by fiber laser have better depth-to-width ratio; the fit-up gap adjustability of fiber laser is better than Slab CO2 laser.
- 1 January 2009
- Published by Laser Institute of America
- Vol. 2009 (1) , 1569-1572
Comparative study on the application of fiber laser and slab CO2 laser in welding DP780 high strength steel plate
Welding experiments of high strength steel plate produced by Baosteel with IPG YLR-6000-ST2 fiber laser and Slab CO2 laser have been processed. The differences of laser in practical application have been investigated through the contrast of parameters and welding seam dynamic performances. It is showed that the maximum welding speed of fiber laser is 2∼3 times faster than Slab CO2 laser; the welding speed of fiber laser with the power 1300W is as same as Slab CO2 laser 3500W; the samples prepared by fiber laser have better depth-to-width ratio; the fit-up gap adjustability of fiber laser is better than Slab CO2 laser.