MUMesut Uysal

Mesut Uysal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mesut Uysal has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Characterization of PLA–hemp biocomposites produced by hot-pressing

    by Esra Çelik, Mesut Uysal, Çağatay Taşdemir, Ömer Yunus Gümüş

    This study investigates the thermal, chemical, physical, morphological, and mechanical properties of hot-pressed PLA-hemp biocomposites produced without compatibilizers. Hemp particles below 75 µm were composed of PLA at 3%, 6%, and 9 wt%, and neat PLA was evaluated in both granular and extruded forms. The composition was compounded using a twin-screw extruder and converted into plates by hot pressing. TGA showed that extrusion slightly improved the thermal stability of neat PLA, whereas hemp addition reduced degradation temperatures. DSC results demonstrated that hemp fibers increased earlier crystallization and the crystallinity of the PLA matrix. FTIR spectra showed that the interaction between PLA and hemp was mainly physical but there is no evidence of new chemical bond formation. Water absorption and thickness swelling increased with hemp content, reaching the highest values in PLA-H9. Surface roughness was significantly affected by sample type, while tensile and flexural strengths decreased after hemp incorporation. SEM images depicted fiber pull-out, interfacial debonding, and micro voids, confirming limited matrix–fiber adhesion. Overall, hemp addition improved bio-based content but reduced strength without compatibilization.

  • Open Access

    Experimental and Numerical Analysis of Screw Withdrawal Strength of Cross-Laminated Timbers

    by Seyma Alpaslan, Halil Karatay, Orhan Eren, Mesut Uysal

    This study examines the impact of screw penetration depth and wood species on the SWS of CLT panels, utilizing a combination of experimental testing and FEA to assess performance. CLT panels were fabricated from Uludağ fir and black pine, and screw withdrawal tests were performed at two penetration depths corresponding to two- and three-layer. The average densities of CLTs were 0.44 g/cm3 for Uludağ fir and 0.52 g/cm3 for black pine, with respective moisture contents of 11.37% and 11.08%. The average SWS for Uludağ fir CLTs increased from 9.73 N/mm2 (two-layer) to 11.27 N/mm2 (three-layer), representing a 15.83% enhancement, while black pine CLTs improved from 13.85 N/mm2 to 14.72 N/mm2 (6.28% increase) with an increase in penetration depth from two to three-layer. Statistical analysis confirmed significant effects of both wood species and penetration depth. FEA simulations predicted withdrawal resistances of 2950.41–3115.94 N for Uludağ fir and 3339.19–3969.73 N for black pine, with two and three-layer penetration depths, respectively. The differences between the experimental and numerical results ranged from 3.69% to 50.10%. Approximately 62.50% of comparisons were within an acceptable 24% deviation range for wood materials. The results indicate that denser species and greater penetration depth enhance withdrawal performance, while FEA provides reasonably accurate yet conservative estimates. The developed experimental–numerical framework provides a reliable predictive basis for designing and optimizing screw connections in wooden constructions, contributing to safer, more efficient, and sustainable CLT-based building systems.

  • Moisture-dependent dynamic elasticity of wood: A non-destructive evaluation under varying relative humidity conditions

    by Mesut Uysal, Ergün Güntekin

    This study investigates the influence of moisture content (MC), controlled via oven-drying and relative humidity (RH) at 45%, 65%, and 85%, on the dynamic elastic properties of poplar, fir, spruce, and pine wood. Ultrasonic non-destructive testing (NDT) was used to measure the sound velocity and calculate the dynamic modulus of elasticity (MOE) in the longitudinal (L), radial (R), and tangential (T) directions of the samples. The findings revealed that the highest sound velocity in the L direction was observed in fir (5018 m/s under dry conditions), followed by poplar (4935 m/s), spruce (4912 m/s), and pine (4637 m/s). Correspondingly, the dynamic MOE in the L direction reached up to 12412 MPa for spruce and 10751 MPa for pine. As RH increased, all species showed declines in sound velocity and elasticity, with the radial and tangential directions being more sensitive to moisture variation. Spruce demonstrated the highest reduction rate in elasticity with increasing RH, particularly in the radial and tangential directions, while fir showed relatively stable mechanical behavior. These results underscore the species-specific and anisotropic response of wood to moisture and confirm the effectiveness of ultrasonic NDT for characterizing hygro-mechanical performance. The outcomes contribute to enhanced material selection and their long-term durability assessments for wood applications exposed to variable environmental conditions.

  • Open Access

    Hybrid Layer Thickness Configurations for Enhanced Mechanical Performance and Energy Efficiency FDM-Printed PLA

    by Mesut Uysal

    This study examines the impact of hybrid layer thickness configurations on the mechanical properties and energy consumption of 3D-printed polylactic acid (PLA) parts produced via Fused Deposition Modeling (FDM). PLA specimens with various combinations of outer and core layer thicknesses (0.08 mm, 0.16 mm, and 0.28 mm) were fabricated and tested for tensile strength, flexural strength, and flexural modulus, alongside measurements of energy consumption. The results revealed that hybrid structures incorporating 0.16 mm face layers and 0.08 mm core layers exhibited superior mechanical performance. In contrast, thicker core layers (0.28 mm) significantly reduced printing time and energy use. The highest tensile strength (53.57 MPa), flexural strength (90.68 MPa), and flexural modulus (2898.4 MPa) were obtained in the sample group of 0.16_0.08_0.16 mm layer thickness. Scanning Electron Microscopy (SEM) provided microstructural insights supporting these findings. The porosity and higher nozzle temperature may influence the material strength for thicker and thinner layer thicknesses, respectively. The sample group with the least energy consumption was 0.28 mm, followed by the sample group with the same layer thickness in both the face and core layers. The study highlights the potential of hybrid layering strategies to optimize performance-energy trade-offs in FDM printing, offering valuable guidance for material-efficient and functionally robust additive manufacturing.

  • Some printing parameters affecting the screw withdrawal strength of materials used in joints developed in 3D printers for furniture

    by Mesut Uysal

    This study examined to benchmark the screw withdrawal strength (SWS) of the 3D-printed PLA materials considering various infill patterns and ratios. SWS is one of the critical material properties for furniture joints. For this purpose, dimensions of 10 × 50 × 50 mm specimens made of PLA+ were printed according to ASTM D 6117-18. Three infill patterns (line, grid, and concentric) and four infill ratios (25%, 50%, 75%, and 100%) were used as printing parameters to construct a complete 3 × 4 factorial experiment. According to the results, line infill patterns had the highest density compared to the grid and concentric patterns for all infill ratios. Concentric infill patterns with an infill ratio of 100% (108.41 MPa) had the greatest SWS. Grid infill patterns provided higher strength at the lower infill ratios than line and concentric infill patterns. Here, diffusion for interfaces of strands affected the SWSs of the 3D-printed materials. This study would provide insight into the 3D-printed joints in the field of furniture mechanics.


  • Open Access

    The diagonal tensile strength of corner joints constructed with different connectors

    by Halil Karatay, Merve Fatma Akbaş, Mesut Uysal

    This study aimed to investigate the strength and stiffness of corner joints for case furniture in the diagonal tension test. For this purpose, joint members were constructed with medium-density fiberboard (MDF) and particleboard (PB) with minifix, butterfly, and trapeze connectors. The study also observed the role of the end distance of the connectors, which was found to be a factor in joint strength and stiffness. According to the results, joints made of MDF performed 16 to 92 % better compared to PB, considering connectors on joints, which was evident due to material properties that MDF were denser by 7.5% and more strengthfull by 177% than PB. The butterfly connectors had the highest strength and stiffness regardless of material type and end distance, followed by trapeze connectors. The joints with minifix connectors had strength and stiffness of 2-3 times lower than others. Moreover, the end distance of 75 mm provided slightly higher joint strength and stiffness compared to those of 50 mm but was not statistically significant. Consequently, butterfly connectors demonstrated markedly the highest strength and stiffness for corner joints of case furniture. Furniture made of MDF should be chosen for higher durability rather than PB.


  • 3D-Printed biocomposites from hemp fibers reinforced polylactic acid: Thermal, morphology, and mechanical performance

    by Esra Celik, Mesut Uysal, Omer Yunus Gumus, Cagatay Tasdemir

    Thermal, morphological, and mechanical properties were studied for 3D-printed biocomposites prepared from polylactic acid (PLA) and hemp fibers. For this purpose, the neat PLA, PLA/Hemp fiber (3 wt%), PLA/Hemp fiber/Maleic anhydride (3 wt% and 0.6 wt%), and PLA/Hemp fiber/Maleic anhydride/Glycerol (3 wt% and 0.6 wt% + Glycerol added in 10% of PLA) biocomposites were extruded to obtain filaments for fused filament fabrication (FFF). Thermogravimetric analysis (TGA) provided temperatures corresponding to 5%, 10%, and 90% mass losses for materials before and after 3D printing. During 3D printing, filaments were extruded with a nozzle temperature of 220 ºC; consequently, their thermal properties worsened after 3D printing. In thermal analysis, Tg increased by adding hemp fiber and maleic anhydride but was decreased with glycerol addition. The tensile and flexural strengths of neat PLA and biocomposites were not statically different, but flexural strength was slightly increased by adding ingredients one by one. Regarding modulus of elasticity (MOE) of materials, the sample group of the PLA/hemp fiber/maleic anhydride had the highest value. However, glycerol addition decreased MOE by 17%. These results showed that material performance of the PLA could be improved or remain statistically identical by adding hemp fiber, maleic anhydride, and glycerol.


  • Open Access

    Çapraz lamine kerestelerin sonlu elemanlar metodu ile analizi

    by Halil Karatay, Ergün Güntekin, Mesut Uysal

    Çalışmada, Çapraz Lamine Kerestelerin (ÇLK) Sonlu Elemanlar Metodu (SEM) ile yük altında eğilme davranışları incelenmiş; literatürde yer alan Uludağ göknarı ve karaçam odunundan elde edilen ÇLK’lerin eğilme özellikleri kullanılmış ve çalışma sonuçları ile karşılaştırılmıştır. ANSYS sonlu elemanlar yazılımı kullanılarak ahşap mal-zemenin ortotropik malzeme özellikleri ve laminasyonda kullanılan tutkallama dikkate alınarak modeller oluştu-rulmuştur. Uludağ göknarı odunundan elde edilen ÇLK’lerde malzemenin yük-deformasyon eğrisi 700 N yük uygulamasından sonra lineer bölgeden uzaklaşırken, karaçam odunundan elde edilen ÇLK’lerde ise 1400 N’dan sonra uzaklaşmaktadır. Uludağ göknarı’ndan elde edilen ÇLK’lerde 800 N altındaki deformasyon 10,50 mm iken karacam odunundan elde edilen ÇLK’lerde ise 13,85 mm’dir. Ayrıca, nümerik analizlerden elde edilen yük-deformasyon grafikleri ile deneysel sonuçların gösterildiği verilerdeki yük-deformasyon eğrileri uyumludur. Çalış-manın sonuçları, karaçam ve Uludağ göknarı odunundan elde edilen ÇLK’lerin ortotropik özellikleri kullanılarak bilgisayarlı ortamda simüle edilmesi yerli odun türlerimizin yapı sektöründe kullanılması açısından önem arz etmektedir.

  • Kontrplak ile güçlendirilmiş yongalevha ve MDF levhaların eğilme davranışının deneysel ve nümerik analizi

    by Ergün Güntekin, Mesut Uysal

    Bu çalışmada, kontrplak kullanılarak güçlendirilmiş yongalevha ve MDF levhaların eğilme davranışı deneysel ve nümerik yöntemler ile incelenmiştir. Çalışmada 13 mm YL ve 12 mm MDF levhalar 4 mm kalınlığında kayın kontrplak kullanılarak güçlendirilmiştir. Levhaların yapıştırılmasında poliüretan tutkalı kullanılmıştır. Deney örnekleri 3 nokta eğilme testine tabi tutularak eğilme davranışları belirlenmiştir. Çalışmada test edilen güçlendirilmiş örneklerin sonlu elemanlar modelleri oluşturularak nümerik analizleri yapılmıştır. Çalışma sonuçları kontrplak kullanarak güçlendirilmiş yongalevha örneklerin eğilmede elastikiyet modülü ve eğilme direnci yükleme yönüne göre iki katına kadar, MDF örneklerinde ise %44 artmıştır. Güçlendirmenin etkinliği yükleme yönüne göre değişmektedir. Çekme gerilmesine maruz kalan yüzeylerin güçlendirilmesi basma gerilmesine maruz kalan yüzeylerin güçlendirilmesine göre eğilme özelliklerine daha fazla katkı yapmıştır. Eğilme testlerinden elde edilen yük-deformasyon eğrileri ile nümerik analizlerden elde edilen yük-deformasyon eğrilerinin çoğunlukla benzer olduğu görülmektedir. Çalışma sonuçları KP kullanılarak güçlendirilmiş YL ve MDF levhaların eğilme davranışlarının sonlu elemanlar yöntemi kullanarak tahmin edilebileceğini göstermiştir.