Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ergün Güntekin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Moisture-dependent dynamic elasticity of wood: A non-destructive evaluation under varying relative humidity conditions

    by Mesut Uysal, Ergün Güntekin

    This study investigates the influence of moisture content (MC), controlled via oven-drying and relative humidity (RH) at 45%, 65%, and 85%, on the dynamic elastic properties of poplar, fir, spruce, and pine wood. Ultrasonic non-destructive testing (NDT) was used to measure the sound velocity and calculate the dynamic modulus of elasticity (MOE) in the longitudinal (L), radial (R), and tangential (T) directions of the samples. The findings revealed that the highest sound velocity in the L direction was observed in fir (5018 m/s under dry conditions), followed by poplar (4935 m/s), spruce (4912 m/s), and pine (4637 m/s). Correspondingly, the dynamic MOE in the L direction reached up to 12412 MPa for spruce and 10751 MPa for pine. As RH increased, all species showed declines in sound velocity and elasticity, with the radial and tangential directions being more sensitive to moisture variation. Spruce demonstrated the highest reduction rate in elasticity with increasing RH, particularly in the radial and tangential directions, while fir showed relatively stable mechanical behavior. These results underscore the species-specific and anisotropic response of wood to moisture and confirm the effectiveness of ultrasonic NDT for characterizing hygro-mechanical performance. The outcomes contribute to enhanced material selection and their long-term durability assessments for wood applications exposed to variable environmental conditions.

  • Eğilmeye maruz bırakılmış PVC köpük çekirdekli sandviç levhaların deneysel ve sayısal analizi

    by Ergün Güntekin

    Bu çalışmada, eğilmeye maruz bırakılan PVC köpük çekirdek ve kontrplak/MDF yüzeyler kullanılarak oluşturulan sandviç levhalar, deneysel ve sayısal yöntemler kullanılarak analiz edilmiştir. Sandviç levhalarda çekirdek olarak 60 kg/m3 yoğunlukta PVC köpük, yüzey malzemeleri olarak kayın kontrplak ve MDF kullanılmıştır. Sandviç katmanları çift bileşenli epoksi yapıştırıcı kullanılarak yapıştırılmıştır. Çalışmada kullanılan kontrplak ve MDF malzemelerin eğilme özellikleri belirlenerek sayısal modellemede kullanılmıştır. PVC köpük için üretici tarafından belirtilen elastikiyet değeri kullanılmıştır. Çalışmanın sonuçları, yüzey malzeme türünün PVC köpük çekirdekli sandviç levhaların eğilme davranışını önemli ölçüde etkilediğini göstermiştir. Kontrplak yüzeyler kullanıldığında, PVC köpük çekirdekli sandviç levhaların eğilmeye rijitliğinin ve dayanımının daha yüksek olduğu bulunmuştur. Test edilen sandviç levhalarda, baskın arıza türü yüzey malzemesinin kırılmasıdır. MDF yüzeylerde üst yüzeyde kırışma ve MDF/çekirdek kırılması gözlemlenmiştir. Çalışmanın sonuçları, sayısal modellerin, malzemelerin akma gerilmesi ve teğet modülü (plastik bölge) kullanılarak sandviç levhaların kırılmaya kadar olan eğilme davranışını doğru bir şekilde tahmin etmek için kullanılabileceğini göstermektedir.

  • Performance Evaluation of Hybrid Sandwich Panels Composed of Recycled Particleboard Cores and MDF Face Materials

    by Ahmet Dedeağaçlı, Ergün Güntekin

    This study investigated the recovery potential and reuse possibilities of waste particleboards. , Waste particleboards were used as sandwich cores through two different methods. In the first method, waste particleboards obtained from different sources were recycled by processing them through a chipping machine. The resulting chips were sieved and classified to ensure homogeneity in terms of size and shape. After the classification, the chips were dried to obtain homogeneous moisture content. The chips were then used in the production of single-layer particleboards bonded with urea-formaldehyde adhesive. The produced single-layer particleboards had a target density of 0.5 g/cm3, a thickness of 10 mm, and an adhesive content of 10 % based on oven dried weight of the dry chip amount. The surfaces of the produced single-layer particleboards were bonded to 4 mm thick MDF boards using PVA adhesive, and sandwich boards were produced by cold pressing. In the second method, used particleboard was cut into 10 mm wide strips and used directly as sandwich panel cores. The face materials and adhesive in this method were the same as those used in the first method. The resulting sandwich materials were conditioned at 65% humidity and 21 °C. Test specimens were cut from the sandwich panels and evaluated for density, thickness swelling, and bending properties. The modulus of elasticity and bending strength values of sandwich panels ranged from 1861 to 2974 N/mm2, and 16.90 to 26.75 N/mm2, respectively. The sandwich panels manufactured using second method yielded thickness swelling values lower than 15%. The results of the study showed that waste particleboard can be successfully reused in sandwich panel production.

  • Open Access

    Microstructural Evolution and Physico-Mechanical Response of Cement-Bonded Fiberboards: A Comparative Study on Cement Type and Fiber Ratio

    by Emrecan Arpaci, Sebnem S. Arpaci, Ergun Guntekin

    This study investigates the interplay between Portland cement strength class (32.5, 42.5, and 52.5) and fiber/cement ratio (ranging from 1/2 to 1/5 by weight) to optimize the physical-mechanical and thermal performance of cement-bonded fiberboards. The experimental data revealed a distinct trade-off: while reducing the fiber content towards a 1/5 ratio significantly improved flexural strength and dimensional stability through matrix densification, it inevitably compromised thermal insulation. Among the binders evaluated, the 42.5 strength class emerged as the most effective option, outperforming the 32.5 class and, notably, offering a more balanced profile than the 52.5 class. The highest stiffness was recorded with the 42.5 cement at a 1/5 ratio (modulus of elasticity (MOE): 5902 ± 532 N/mm2; modulus of rupture (MOR): 12.49 ± 0.6 N/mm2), yielding performance metrics comparable to the 1/4 ratio (MOR: 12.78 N/mm2). Furthermore, this formulation demonstrated superior moisture resistance, achieving water absorption (WA) values as low as 18.9%. Thermal conductivity (TC) measurements at 20 °C confirmed that while fiber-rich mixtures (1/2 ratio) favored insulation, the 42.5 cement at a 1/4 ratio maintained a competitive conductivity value (λ = 0.1625 W/mK), lower than that of the 52.5 grade, thereby striking a critical balance between structural integrity and thermal efficiency. Statistical analyses (Two-way ANOVA, p < 0.05) corroborated the significant influence of both cement type and mix ratio. Microstructural insights from Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) suggest that the superior performance of the 42.5 cement is associated with optimized hydration kinetics and a well-graded particle size distribution (D50 = 14.80 µm), which together facilitated effective fiber encapsulation.

  • Open Access

    Optimizing Mechanical and Thermal Properties of Slag-Based Geopolymer Fiber Boards via Fiber Pretreatment and Reinforcement Type

    by Sebnem Sevil Arpaci, Ergun Guntekin

    This study aims to optimize the physical, mechanical, and thermal properties of 100% Ground Granulated Blast Furnace Slag (GGBFS) based geopolymer wood-composite panels. Pine fibers were utilized as the primary reinforcement matrix, while glass and hemp fibers were introduced as secondary reinforcements at varying proportions (3%, 6%, 9% by weight). The research investigated the effects of fiber pretreatments (hot water vs. 1% NaOH) and reinforcement hybridization. Results indicate that GGBFS successfully geopolymerized, forming a hybrid N-A-S-H and C-A-S-H gel network. Quantitative analysis revealed that 9% glass fiber reinforcement yielded the highest mechanical performance, achieving a Modulus of Rupture (MOR) of 10.05 N/mm2 and Internal Bond (IB) strength of 1.32 N/mm2, alongside superior water resistance (1.0% Thickness Swelling). Conversely, while hemp fiber inclusion reduced mechanical strength (MOR: 5.77 N/mm2 at 9%), it significantly enhanced thermal insulation, reducing thermal conductivity to 0.10 W/m·K. It was observed that aggressive NaOH pretreatment caused alkali-induced degradation of pine fibers, negatively impacting the composite’s integrity compared to hot water treatment. This study demonstrates the feasibility of tailoring 100% slag-based geopolymer composites for either structural (glass-reinforced) or insulating (hemp-reinforced) applications using industrial by-products.


  • Open Access

    Microstructural Evolution and Physico-Mechanical Response of Cement-Bonded Fiberboards: A Comparative Study on Cement Type and Fiber Ratio

    by Emrecan Arpaci, Sebnem S. Arpaci, Ergun Guntekin

    This study investigates the critical interplay between cement grade (32.5, 42.5, 52.5) and fiber/cement ratio (1/2 to 1/5) in determining the performance of cement-bonded fiberboards. Experimental results highlighted a fundamental trade-off: while reducing the fiber content significantly enhanced mechanical strength and moisture resistance, it naturally diminished thermal insulation capabilities. The analysis identified the 42.5 cement at a 1/4 ratio as the optimal formulation, offering the most effective balance between structural integrity and physical stability. To understand the mechanism behind this performance, the study employed multi-scale characterization using FTIR, XRD, and SEM. These analyses revealed that the superior properties of the optimal formulation stem from a denser hydration product network and improved fiber encapsulation. Specifically, the 42.5 cement facilitated a more robust Calcium-Silicate-Hydrate (C-S-H) gel formation compared to the 32.5 types, creating a stronger fiber-matrix interface. These findings provide a scientific basis for tailoring fiberboard production, demonstrating that material properties can be precisely engineered for either load-bearing or insulating applications.


  • PVC esaslı bazı OPK profillerin eğilme davranışının deneysel ve sonlu elemanlar analizi

    by Ergün Güntekin

    Ticari olarak üretilen polivinil klorür (PVC) esaslı bazı odun plastik kompozit (OPK) profillerin eğilme özellikleri deneysel ve sayısal yöntemler kullanılarak analiz edilmiştir. İlk olarak, PVC-odun unu kompozitlerinin elastikiyet modülü ASTM D790 standardına göre 3 nokta eğilme testleri kullanılarak küçük numuneler üzerinde belirlenmiştir. Üç farklı OPK profili deneysel olarak test edilmiş ve sonlu elemanlar yöntemi kullanılarak modellenmiştir. Sayısal modellemede izotropik malzeme özellikleri kullanılmıştır. Çalışmanın sonuçları, sayısal modellerin OPK profillerinin eğilme davranışının gerçekçi bir şekilde tahmin edilmesinde kullanılabileceğini göstermektedir. OPK profillerinin eğilme rijitlikleri benzer, ancak direnç özellikleri önemli ölçüde farklı bulunmuştur. Çalışma sonuçları OPK profillerin izotropik malzeme özellikleri kullanılarak modellenebileceğini göstermiştir.

  • Open Access

    Optimizing Mechanical and Thermal Properties of Slag-Based Geopolymer Fiber Boards via Fiber Pretreatment and Reinforcement Type

    by Sebnem Sevil Arpaci, Ergun Guntekin

    This study aims to optimize the physical, mechanical, and thermal properties of 100% Ground Granulated Blast Furnace Slag (GGBFS) based geopolymer wood-composite panels. Pine fibers were used as the primary reinforcement, while glass and hemp fibers were added as secondary reinforcements. The research investigated the effects of fiber pretreatments (hot water and 1% sodium hydroxide (NaOH) solution and varying proportions (3%, 6%, 9% by weight) of these secondary reinforcements on the slag-based geopolymer matrix. Properties such as density, water absorption (WA), thickness swelling (TS), thermal conductivity (λ), modulus of rupture (MOR), modulus of elasticity (MOE), and internal bond (IB) strength were determined. Furthermore, microstructural and chemical interactions were examined through Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), and Scanning Electron Microscopy (SEM) analyses. Results indicate that GGBFS successfully geopolymerized upon alkali activation, exhibiting strong mechanical properties due to the formation of N-A-S-H and C-A-S-H gels. While hot water pretreatment provided a slight improvement in the fiber-matrix interface, NaOH pretreatment led to alkali-induced degradation, causing significant reductions in performance. Glass fiber reinforcement generally resulted in higher density and systematically increased MOR, MOE, and IB values, significantly enhancing the mechanical performance and water resistance of the composites. In contrast, hemp fiber reinforcement typically yielded lower density values and reduced mechanical properties due to fiber agglomeration and high hydrophilicity. However, HF-containing groups, particularly with 9% addition, showed a notable reduction in thermal conductivity (down to 0.10 W/m·K), suggesting potential for lightweight insulation applications. FTIR, XRD, and SEM analyses corroborated the effects of fiber-matrix interactions and microstructural defects on the observed macro-properties. This study provides valuable insights into utilizing industrial and agricultural wastes in geopolymer composites, supporting sustainable and carbon-neutral construction goals.

  • Open Access

    Experimental and Numerical Analysis of Sandwich Panels Made of Different Core Materials with Plywood Facing

    by Ergün Güntekin, Mesut Uysal

    Sandwich panels composed of different core materials with plywood facings were analyzed using experimental and numerical methods. Particleboard (PB), fiberboard (MDF), and foam materials were used as the core of the sandwich, while beech plywood was laid as the only face material. The layers of the sandwich were adhered with polyurethane adhesive. Elasticities (E) of PB, MDF, and plywood were determined in the laboratory. The E value specified by the manufacturer for the foam was used to determine the flexural behavior of sandwich panels. Results of the study indicated that the type of core material significantly affects the bending behavior of sandwich panels with plywood facings. Sandwich panels with MDF-core were observed to be more resistant in bending compared to PB and foam-core sandwich panels. Core shear failure was the dominant failure type when wood-based materials were used as core material. Buckling or tension in facing was observed when foam was used as core material. The results of the study demonstrate that numerical models can be used to accurately predict the bending behavior of the sandwich panels until failure based on yield stress and tangent modulus of the materials.


  • Open Access

    Effects of heat treatment on elastic constants of Cedar (Cedrus libani) wood

    by Ergün Güntekin

    The aim of this study was to evaluate the effects of heat treatment on the elastic constants of Cedar (Cedrus liba-ni) wood. Heat under atmospheric pressure at three different temperatures (150, 180 and 210 °C) and three differ-ent time levels (2, 5 and 8 hours) was applied to Cedar wood specimens and its Modulus of elasticity (EL, ER, ET) shear modulus (GLR, GLT, GRT) and Poisson’s ratios (νLR, νLT, νRL, νRT, νTL, νTR) were evaluated by compression tests conducted on 20 x 20 x 60 mm samples using bi-axial extensometer. It was observed that the modulus of elastici-ty, shear modulus, and compression strength of the tested specimens were significantly affected by the temperature and time parameters of the heat treatment. Treatment of heat for low temperatures and short periods yielded some increase in modulus of elasticity but an increase in time and temperature resulted in a significant decrease. Heat treatment has a devastating influence on the shear modulus. Poisson’s ratios were less sensitive to the heat treat-ment. Heat treatment significantly alters the modulus of elasticity, shear modulus and compression strength of Cedar wood.