Almir Turazi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Almir Turazi has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Alexandre Galiotto
Department of Mechanics, Instituto Federal de Santa Catarina - IFSC 1 , Rua dos Imigrantes, 445, Jaraguá do Sul, Santa Catarina 89254-430
2 shared publications - Fernando Henrique Gruber Colaço
Department of Mechanics, Instituto Federal de Santa Catarina - IFSC 1 , Rua dos Imigrantes, 445, Jaraguá do Sul, Santa Catarina 89254-430
2 shared publications - Gil Magno Portal Chagas
Department of Mechanics, Instituto Federal de Santa Catarina - IFSC 1 , Rua dos Imigrantes, 445, Jaraguá do Sul, Santa Catarina 89254-430
2 shared publications - Giuseppe Pintaude
Surface and Contact Lab (LASC), Academic Department of Mechanics, Universidade Tecnológica Federal do Paraná, Curitiba 81280-340, Brazil
2 shared publications - Joel Stryhalski
Federal Institute of Santa Catarina, Jaragu do Sul, Santa Catarina, Brazil
2 shared publications Arthur Henrique Ribeiro Souto
Instituto Federal de Santa Catarina, Brasil
1 shared publication
Latest Publications
- 15 September 2023
- Published by ASTM International in Materials Performance and Characterization
- Vol. 12 (3) , 396-404
Wear Resistance of Fe–Cr–C Hardfacing Deposited by Flux-Core-Double-Wire GTAW in Rubber Wheel Abrasion Test
The wear resistance of metals can be improved by using the hardfacing technique. Different processes can produce it with the desirable microstructures and mechanical properties. This study presents an original method, flux-core-double-wire of gas-shielded tungsten arc welding, in which wires of different compositions are used simultaneously to obtain different microstructures. The deposition was controlled through the following parameters: welding speed, deposition current, standoff distance, torch angle, and pulse frequency of wire feed. Four coatings were deposited on AISI 1020 steel substrate by combining the cored wires: Fe–Cr–C, Fe–Cr–C–Nb, Fe–Cr–C–Mo–Nb, and Fe–Cr–C–Mo–Ti. The combination of these wires resulted in a hypoeutectic microstructure with niobium and titanium carbides, with an average hardness of 650 HV0.3. The hypereutectic microstructures were formed by different niobium contents, with a microhardness range from 820 to 1,020 HV0.3. The performance of the hardfacing was evaluated in the rubber wheel abrasion test described by ASTM G65, Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus (Superseded), procedure B. The results revealed that the carbide cracking distinguished the wear resistance, and the hardness was not enough to separate the wear behavior. Still, the volume fraction of carbides was a decisive microstructural parameter.
- 15 September 2023
- Published by ASTM International in Materials Performance and Characterization
- Vol. 12 (3) , 396-404
Wear Resistance of Fe–Cr–C Hardfacing Deposited by Flux-Core-Double-Wire GTAW in Rubber Wheel Abrasion Test
The wear resistance of metals can be improved by using the hardfacing technique. Different processes can produce it with the desirable microstructures and mechanical properties. This study presents an original method, flux-core-double-wire of gas-shielded tungsten arc welding, in which wires of different compositions are used simultaneously to obtain different microstructures. The deposition was controlled through the following parameters: welding speed, deposition current, standoff distance, torch angle, and pulse frequency of wire feed. Four coatings were deposited on AISI 1020 steel substrate by combining the cored wires: Fe–Cr–C, Fe–Cr–C–Nb, Fe–Cr–C–Mo–Nb, and Fe–Cr–C–Mo–Ti. The combination of these wires resulted in a hypoeutectic microstructure with niobium and titanium carbides, with an average hardness of 650 HV0.3. The hypereutectic microstructures were formed by different niobium contents, with a microhardness range from 820 to 1,020 HV0.3. The performance of the hardfacing was evaluated in the rubber wheel abrasion test described by ASTM G65, Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus (Superseded), procedure B. The results revealed that the carbide cracking distinguished the wear resistance, and the hardness was not enough to separate the wear behavior. Still, the volume fraction of carbides was a decisive microstructural parameter.
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 26 (suppl 1) , e20220600
Dry Sliding Wear Resistance of Fe-Cr-C hardfacing Deposited by Flux-Core-Double-Wire GTAW
Gas-Shielded Tungsten Arc Welding (GTAW) was modified to a Flux-Cored-Double-Wire GTAW (FCDW-GTAW); in this technique, wires of different compositions are used simultaneously to obtain different microstructures. In the modified GTAW, automatic flux-cored double-wire was used with a combination of four different wires deposited in AISI1020 steel, allowing different microstructures. Pin-on-disk wear tests described by ASTM G99 was used to evaluate the wear coefficients of four hardfacing materials combining Fe–Cr–C, Fe-Cr-C-Nb, Fe-Cr-C-Mo-Nb, and Fe-Cr-C-Mo-Ti alloys. The combination of these wires resulted in a hypoeutectic microstructure with niobium and titanium carbides, with an average hardness of 650 HV0.3, and hypereutectic microstructures formed by different niobium contents, with a microhardness range from 820 to 1020 HV0.3. The wear tests were performed without lubrication at room temperature, using a 6.0 mm diameter polished alumina sphere as a counter-body. The total distance covered was 1000 m with a speed of 0.1 m/s, a track radius of 6.0 cm, and an applied load of 10 N. Hardness, microstructure, wear coefficient, and wear mechanisms were compared. The results showed that wear resistance could be differentiated by the predominant wear mechanism: polishing for the hypoeutectic hardfacing and cracking for the hypereutectic ones.
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 26 (suppl 1) , e20220600
Open AccessDry Sliding Wear Resistance of Fe-Cr-C hardfacing Deposited by Flux-Core-Double-Wire GTAW
Gas-Shielded Tungsten Arc Welding (GTAW) was modified to a Flux-Cored-Double-Wire GTAW (FCDW-GTAW); in this technique, wires of different compositions are used simultaneously to obtain different microstructures. In the modified GTAW, automatic flux-cored double-wire was used with a combination of four different wires deposited in AISI1020 steel, allowing different microstructures. Pin-on-disk wear tests described by ASTM G99 was used to evaluate the wear coefficients of four hardfacing materials combining Fe–Cr–C, Fe-Cr-C-Nb, Fe-Cr-C-Mo-Nb, and Fe-Cr-C-Mo-Ti alloys. The combination of these wires resulted in a hypoeutectic microstructure with niobium and titanium carbides, with an average hardness of 650 HV0.3, and hypereutectic microstructures formed by different niobium contents, with a microhardness range from 820 to 1020 HV0.3. The wear tests were performed without lubrication at room temperature, using a 6.0 mm diameter polished alumina sphere as a counter-body. The total distance covered was 1000 m with a speed of 0.1 m/s, a track radius of 6.0 cm, and an applied load of 10 N. Hardness, microstructure, wear coefficient, and wear mechanisms were compared. The results showed that wear resistance could be differentiated by the predominant wear mechanism: polishing for the hypoeutectic hardfacing and cracking for the hypereutectic ones.