AKAlexey Kushchev

Alexey Kushchev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alexey Kushchev has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    СТЕНД КОНТРОЛЮ МІКРОЗАБРУДНЕННЯ ЯК ІНСТРУМЕНТ ЯКІСНОЇ ДІАГНОСТИКИ МІНІАТЮРНИХ ШАРИКОПІДШИПНИКІВ

    by Олександр Стельмах, Руслан Костюнік, Рудольф Мнацаканов, Олексій Кущев, Сергій Шимчук

    Проведено оцінку конструктивних особливостей, науково-практичного потенціалу та ефективності застосування новоствореного чотириканального вимірювального стенду вхідного контролю мікрозабруднень мініатюрних і прецизійних кулькових підшипників, призначених для прецизійних механічних систем авіаційної та оборонної техніки. Проаналізовано негативний вплив сторонніх твердих і м'яких мікрочастинок на деградацію робочих поверхонь доріжок кочення, що призводить до локальних надвисоких контактних напружень, абразивного зносу, заклинювання та інтенсивного втомного викришування. Обґрунтовано впровадження інвертованої кінематичної схеми стенду, за якої обертається зовнішнє кільце підшипника, а датчики монтуються на нерухомому внутрішньому валу, що забезпечує безконтактний магнітний розгін, виключення сторонніх завад, максимальну чутливість до мікрочастинок бруду та захист сенсорів від динамічних похибок обертання. Описано технічні характеристики синхронного чотириканального збору даних, який об'єднує оптичний канал для фіксації частоти обертання і часу вибігу, вібраційний канал для цифрової обробки сигналів і обчислення пік-фактора й ексцесу, акустичний канал на базі датчика акустичної емісії та мікрофона, а також силовий канал для точної реєстрації чистого моменту тертя методом реакції корпусу. Проведено серію експериментальних порівняльних вимірювань двох партій мініатронних підшипників NTN 61901ZZ/5K та FAG 6001–C–2HRS до та після проведення процедури реновації. Одержано позитивні результати відновлення віброакустичних характеристик деталей за допомогою комбінованого імпульсно магнітно-турбулентного та ультразвукового очищення в розчиннику нефрас. Доведено, що використання такого комбінованого впливу знижує показники вібропришвидшення підшипників на 66–75%, а коефіцієнт варіації часу вибігу зменшується з початкових 38–42% до 9–28%, забезпечуючи високу однорідність відновленої партії. Одержано підтвердження ефективності методу вільного вибігу як самостійного первинного інструменту експрес-діагностики промислової чистоти та виявлення незворотних геометричних дефектів без залучення складного спектрального аналізу. Проведено оцінку економічного ефекту від впровадження розробленого стенду на авіаремонтних підприємствах за рахунок автоматизації контролю, відновлення придатних деталей та уникнення передчасних відмов навігаційних приладів.

  • Open Access

    Development of Plasma-Sprayed Copper Alloy–Nickel-Clad Graphite Composite Coatings with Enhanced Tribological Properties

    by O. Terentjev, O. Umanskyi, O. Kushchev, V. Varchenko, V. Konoval, O. Bondarenko, V. Kurilovych

    This study is focused on the development of composite plasma-sprayed coatings with a low coefficient of friction based on copper alloys with additions of nickel-clad graphite and on the investigation of their physicomechanical and tribological properties. Composite coatings were produced by atmospheric plasma spraying (APS) from agglomerated powders of copper alloys with the following compositions: BrONG-30 (70 wt.% BrOF10-1 + 30 wt.% nickel-clad graphite), BrOSNG-30 (70 wt.% BrOCTS5-5-5 + 30 wt.% nickel-clad graphite), and LNG-30 (70 wt.% L63 + 30 wt.% nickel-clad graphite). The application of graphite in a nickel shell improves its wettability by the metallic matrix and enhances adhesion. The obtained coatings exhibit high adhesion strength to the substrate (33–38 MPa) and density (94–97%). Tribological tests demonstrated that the LNG-30 – steel 45 friction pair showed the best performance. The inclusion of nickel-clad graphite reduced the friction coefficient by up to 1.5 times and increased wear resistance by up to 3.8 times. Using EDS and Auger spectroscopy, it was established that during friction in the LNG-30 – steel 45 pair, a film consisting of graphite (16–17 nm thick) and oxides of copper, zinc, nickel, and iron is formed on the counterbody wear track. The presence of such oxide films indicates a predominantly oxidative mechanism of friction, with minor adhesive interaction. The proposed coatings are promising for application in friction units, particularly under conditions where the use of liquid lubricants is limited or impossible

  • Open Access

    METHOD OF INCREASING THE WEAR RESISTANCE OF A NICKEL-GRAPHITE-BASED COMPOSITE PLASMA COATING BY ADDING COPPER ALLOYS

    by Oleksii Kushchev, Oleksandr Terentjev, Viktor Varchenko, Tetiana Chevichelova, Ruslan Kostyunik, Oleksandr Umanskyi

    Background. The article considers the possibility of expanding the areas of application of plasma coatings based on the nickel-graphite system by adding lead-free copper alloys to the composition, which have an affinity for the nickel shell of the nickel-graphite powder and, in addition to preserving the tribotechnical properties of nickel-graphite, can provide the necessary level of cohesion of the coating. Objective. The aim of this work is to study the effect of the content of the copper alloy CuAl10Ni5Fe4 when added to nickel-graphite (NPG-75) on the tribotechnical characteristics of the composite plasma coating. Methods. As part of the work to determine the influence of the copper alloy content in nickel-graphite on the tribotechnical properties of the plasma composite coating, friction and wear tests were conducted on samples with 35, 50, 75 and 90 wt.% copper alloy CuAl10Ni5Fe4 in nickel-clad graphite NPG-75 (75 wt.% nickel). The double copper-zinc alloy CuZn10 was used as a standard. Results. It has been experimentally established that plasma coatings based on NPG-75 with the addition of 50 wt.% CuAl10Ni5Fe4 have wear resistance increased by 10 times compared to pure NPG-75 with a friction coefficient significantly lower (0.36) than the CuZn10 standard (0.52). The coating on the counterbody of DIN C45 (hardness 45-48 HRC) is the smallest among the friction pair that were investigated in this work. Reducing the copper alloy content to 35 wt.% is impractical, since this results in active wear of the coating material and its spreading onto the counter body. Further increase in the content of CuAl10Ni5Fe4 powder in the composition leads to the occurrence of setting in the contact zone, as evidenced by a sharp (10-fold) increase in the wear of the coating samples, an increase in the temperature in the contact zone, and a ~ 2-fold increase in the friction coefficient. Conclusions. The optimal content of CuAl10Ni5Fe4 in a plasma coating based on NPG-75 is about 50 wt.%. This material allows you to reduce the friction coefficient from 0.52 (CuZn10) to 0.36 when paired with steel DIN C45. The mass wear of the steel counterbody is also significantly reduced, probably due to a change in the wear mechanism from adhesive (seizing) to oxidative wear. This allows us to significantly expand the scope of application of the Ni-C + CuAl10Ni5Fe4 material in aviation and space technology

  • An Innovative Approach to Non-Contact Cleaning of Mini-Ball Bearings

    by Ruslan Kostyunik, Oksana Mikosianchyk, Oleksandr Stelmakh, Alexey Kushchev, Sergii Shymchuk, Nataliia Zaichuk

    The bearing industry represents a critical segment of the modern economy, directly influencing the operational reliability and service life of various machines, equipment, and components employed in high-responsibility sectors of mechanical engineering and transportation infrastructure. Despite ongoing advancements and technological improvements in rolling bearing manufacturing, there remains a significant risk of residual contamination by particulates of various origins, primarily during production. This problem becomes particularly relevant in the case of miniature rolling bearings, characterized by an outer diameter of less than 30 mm. Conventional cleaning techniques currently applied in industrial practice often demonstrate limited efficiency in removing microcontaminants from hard-to-access zones within non-separable bearing assemblies. This study proposed an innovative non-contact cleaning method based on comprehensive investigations. The technique integrates the synergistic effects of pulsed alternating magnetic fields and ultrasonic excitation, offering enhanced cleaning performance without compromising the structural integrity of precision components. The results of the granulometric composition of the removed contaminant particles of ball bearings by different methods were presented. The optimum angles of bearing inclination were experimentally evaluated at various locations of ultrasonic wave radiation sources and the action of a pulsed magnetic field. The effectiveness of the developed combined method on aircraft ball bearings demonstrated its advantages in removing both large and small contaminants, confirmed by vibration diagnostics and microscopic analysis. Testing of the method at leading aircraft manufacturers underlines the practical significance of the developed approach and has the potential to significantly improve the quality, service life, and reliability of precision parts and mechanisms. Depending on the contamination degree and the bearing type, the cleaning time ranged from several seconds to 2–3 minutes, allowing the developed combined method to be integrated into the manufacturing technological cycle of rolling bearings using the necessary automated systems and equipment as the final cleaning operation. This ensures the principle of improving the innovation of production. Using ultrasonic waves allowed for the removal of the strongest films of complex structure. Overall, combining ultrasound with a pulsed magnetic turbulent cleaning method significantly increased the effectiveness of the cleaning process.


  • Improvement of Operational Parameters for Precision Rolling Bearings by Cleaning Working Surfaces from Micro Pollution of Various Nature

    by A. Stelmakh, R. Kostyunik, O. Mikosianchyk, A. Kushchev, T. Ibraimov, O. Sydorenko, N. Zaichuk, S. Shymchuk

    Author(s): Stelmakh A.1,2, Kostyunik R.2, Mikosianchyk O.2, Kushchev A.2, Ibraimov T.2, Sydorenko O.2, Zaichuk N.3, Shymchuk S.3* Affiliation(s): 1 Beijing