XLXun Liu

Xun Liu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xun Liu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Temperature Dependence Modeling and Design Optimization of VCEsat in Carrier-Storage Trench-Gate IGBTs

    by Anning Chen, Yameng Sun, Kun Ma, Xun Liu, Yang Zhou, Sheng Liu

    Insulated-gate bipolar transistor (IGBT) power modules suffer efficiency degradation at elevated operating junction temperatures. The thermal sensitivity of the collector–emitter saturation voltage (VCEsat) induces thermal stress imbalance, constraining system efficiency and reliability. A multi-resistor cascade network model for carrier-storage trench-gate IGBTs (CS-IGBTs) is established. The simulation results agree with the measurements within 10% error. The model decomposes the temperature coefficient contributions of individual structural regions. Analysis reveals that the drift region resistance dominates the VCEsat temperature coefficient. Based on this finding, a co-doping strategy is proposed through simultaneously increasing the doping concentration in the carrier-storage layer and P+ collector. This approach reduces the temperature sensitivity of carrier mobility in the drift region, thereby optimizing VCEsat’s temperature sensitivity. For the fabricated 1200 V/40 A CS-IGBT, the VCEsat temperature coefficient decreases from 2.38 mV/K to 1.76 mV/K over 300 K to 450 K, which represents a 25.4% reduction. The total switching loss at 450 K decreases from 9.32 mJ to 8.70 mJ, achieving a 6.7% improvement. This device-level optimization suppresses VCEsat’s temperature sensitivity and switching losses, enhancing efficiency in high-temperature power module applications.

  • Open Access

    Investigation of a Physical Model for the Reverse Recovery Characteristics of PT-PIN FRD with a Buffer Layer

    by Yameng Sun, Kun Ma, Xiong Yuan, Anning Chen, Xun Liu, Yifan Song, Xuehan Li, Tongtong Zi, Yang Zhou, Sheng Liu

    As application conditions become increasingly demanding and usage becomes more aggressive, the performance of traditional insulated gate bipolar transistor (IGBT) and fast recovery diode (FRD) systems can no longer meet the required specifications. In these systems, FRDs are required to carry load current and allow current to return from the load to the IGBTs. Consequently, the reverse recovery performance of the FRDs significantly restricts the overall efficiency of the system. Therefore, how to predict the reverse recovery characteristics of the FRDs with greater precision has attracted considerable attention. In this context, this paper presents an in-depth investigation of the high-level injection carrier distribution and reverse recovery characteristics of punchthrough P-I-N (PT-PIN) FRD with a buffer layer. Specifically, the research explores the physical properties of the materials, doping concentrations, and the geometric structure of the devices. Furthermore, it takes into account the complex interactions among carrier recombination, diffusion, and drift, leading to the development of a model that delineates the spatial distribution of carriers and their influence on current conduction. Building upon the traditional step-wise analysis method, subsequently, the temporal aspects of the FRDs reverse recovery process were further segmented. Utilizing the derived carrier distribution model, a reverse recovery analytical model was constructed. The model was validated using a 1200 V, 100 A IGBT with 1200 V, 60 A FRD configured in a reverse parallel arrangement, which demonstrated a 5% improvement in prediction accuracy of VR compared with previous models that employed the lumped charge method. Finally, a range of experiments with varying RG, VCC and IF confirmed the broad applicability of this analytical model.


  • Open Access

    The Mechanism of Short-Circuit Oscillations in Automotive-Grade Multi-Chip Parallel Power Modules and an Effective Mitigation Approach

    by Kun Ma, Yameng Sun, Xun Liu, Yifan Song, Xuehan Li, Huimin Shi, Zheng Feng, Xiao Zhang, Yang Zhou, Sheng Liu

    This paper presents an in-depth analysis of the oscillation phenomenon occurring in multi-chip parallel automotive-grade power modules under short-circuit conditions and investigates three suppression methods. We tested and analyzed two commercial automotive-grade power modules, one containing two chips and the other containing a single chip, and found that short-circuit gate oscillations were more likely to occur in multi-chip parallel packaged modules than in single-chip packaged modules. Through experimental and simulation analyses, we observed that gate oscillations were mainly caused by the interaction between internal parasitic parameters of the module and the external drive circuit, and we found that high drive resistance and low common emitter inductance between parallel chips could effectively suppress gate voltage oscillations. We also analyzed the two mainstream suppression schemes, increasing the drive gate resistance and placing the drive capacitors in parallel. Unfortunately, we found that these suppression schemes were not ideal solutions because both schemes changed the switching characteristics of the power module. As an alternative, we propose a simple and effective solution that involves adding parallel connections between the parallel chips. Simulation calculations showed that this optimized method reduced the emitter inductance between parallel chips in the upper bridge arm by about 30% and in the lower bridge arm by 35%. Through short-circuit experiments conducted at different DC bus voltages, it has been verified that the new optimized solution effectively resolves gate oscillation issues without affecting the switching characteristics of the power module.


  • Open Access

    Digital-Twin-Driven Intelligent Insulated-Gate Bipolar Transistor Production Lines

    by Xiao Zhang, Xun Liu, Yifan Song, Xuehan Li, Wei Huang, Yang Zhou, Sheng Liu

    With the rapid development of novel energy vehicles, power generation, photovoltaics, and other industries, power electronic devices have gained considerable attention. Insulated-gate bipolar transistors (IGBTs) have been widely used in those fields. With the emergence of intelligent manufacturing concepts such as Germany’s “Industry 4.0” and China’s “Made in China 2025”, conventional manufacturing which needs to be upgraded with higher efficiency and yield is rapidly pivoting toward digitalization and intelligence. The digital twin methodology has been extensively used in various industries for constructing virtual models of physical entities, facilitating real-time data interconnection to reduce costs and improve efficiency. This study proposes a modular intelligent IGBT production line based on the digital twin. Real-time data are transmitted from a physical line to a digital line for storage and analysis. The digital line is visualized, and an intelligent management platform containing multiple functions is developed. Additionally, a process simulation database is established to obtain the optimal process parameters. Numerous quality issues that can arise during each process of IGBT packaging are addressed using a problem-solving approach based on the digital twin methodology. Consequently, this digital-twin-based IGBT intelligent production line effectively enhances yield rates and efficiency. IGBT modules with various packaging forms such as ACF, ACE, and ACD are manufactured.


  • Open Access

    Failure Analysis for Gold Wire Bonding of Sensor Packaging Based on Experimental and Numerical Methods

    by Yameng Sun, Kun Ma, Yifan Song, Tongtong Zi, Xun Liu, Zheng Feng, Yang Zhou, Sheng Liu

    There is an increasing demand for the use of automotive sensors where complex working environments may easily lead to failure. Wire pull and shear test models based on finite-element analysis are established to evaluate their reliability by investigating the failure mode and mechanism of gold wire bonding. The effect of shear force position and pull force position on failure is also analyzed. The bonding failure was verified by experiments, which is consistent with the simulation result. The results show that: (1) The three-dimensional quantitative modeling reveals the process of bonding delamination and stress concentration. (2) The bonding–slip method (BSM) is adopted in the gold ball detaching process. The concept of three states, including deformation accumulation, cracking, and disengagement, was put forward to reveal the interface stress evolution trend according to the shear testing results. The results indicate that in the interface, the stress in the deformation accumulation state decreases from the tensile side (or compression side) to the center, and the stress in the cracking and disengagement states reduces gradually from the tensile side to the edge. When the interface is completely separated, the failed shear force concentrates on 42 g. The concept and theory proposed in this work can effectively reveal the failure mechanism of bonding interface and help to establish a new failure criterion.


  • Open Access

    A Micromechanical Analysis to the Viscoplastic Behavior of Sintered Silver Joints under Shear Loading

    by Kun Ma, Xun Liu, Yameng Sun, Yifan Song, Zheng Feng, Yang Zhou, Sheng Liu

    Ag paste has been recognized as a promising substitute for Sn/Pb solder in SiC or GaN power electronic devices, owing to its ability to withstand high temperatures and facilitate low-temperature packing. The reliability of these high-power circuits is greatly influenced by the mechanical properties of sintered Ag paste. However, there exist substantial voids inside the sintered silver layer after sintering, and the conventional macroscopic constitutive models have certain limitation to describe the shear stress–strain relationship of sintered silver materials. To analyze the void evolution and microstructure of sintered silver, Ag composite pastes composed of micron flake silver and nano-silver particles were prepared. The mechanical behaviors were studied at different temperatures (0–125 °C) and strain rates (1 × 10−4–1 × 10−2) for Ag composite pastes. The crystal plastic finite element method (CPFEM) was developed to describe the microstructure evolution and shear behaviors of sintered silver at varied strain rates and ambient temperatures. The model parameters were obtained by fitting experimental shear test data to a representative volume element (RVE) model built on representative volume elements, also known as Voronoi tessellations. The numerical predictions were compared with the experimental data, which showed that the introduced crystal plasticity constitutive model can describe the shear constitutive behavior of a sintered silver specimen with reasonable accuracy.