Yifan Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yifan Song has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Kun Ma
School of Power and Mechanical Engineering, Wuhan University, Wuhan, China
3 shared publications - Sheng Liu
Wuhan University
3 shared publications - Xun Liu
Institute of Technological Sciences, Wuhan University, Wuhan 430072, China
3 shared publications - Yameng Sun
School of Integrated Circuits, Wuhan University, Wuhan, China
3 shared publications - Yang Zhou
Hefei Archimedes Electronic Technology Co., Ltd., Hefei 230094, China
3 shared publications - Zheng Feng
Hefei Archimedes Electronic Technology Co., Ltd., Hefei 230000, China
2 shared publications
Latest Publications
- Open Access
The Mechanism of Short-Circuit Oscillations in Automotive-Grade Multi-Chip Parallel Power Modules and an Effective Mitigation Approach
This paper presents an in-depth analysis of the oscillation phenomenon occurring in multi-chip parallel automotive-grade power modules under short-circuit conditions and investigates three suppression methods. We tested and analyzed two commercial automotive-grade power modules, one containing two chips and the other containing a single chip, and found that short-circuit gate oscillations were more likely to occur in multi-chip parallel packaged modules than in single-chip packaged modules. Through experimental and simulation analyses, we observed that gate oscillations were mainly caused by the interaction between internal parasitic parameters of the module and the external drive circuit, and we found that high drive resistance and low common emitter inductance between parallel chips could effectively suppress gate voltage oscillations. We also analyzed the two mainstream suppression schemes, increasing the drive gate resistance and placing the drive capacitors in parallel. Unfortunately, we found that these suppression schemes were not ideal solutions because both schemes changed the switching characteristics of the power module. As an alternative, we propose a simple and effective solution that involves adding parallel connections between the parallel chips. Simulation calculations showed that this optimized method reduced the emitter inductance between parallel chips in the upper bridge arm by about 30% and in the lower bridge arm by 35%. Through short-circuit experiments conducted at different DC bus voltages, it has been verified that the new optimized solution effectively resolves gate oscillation issues without affecting the switching characteristics of the power module.
Open AccessThe Mechanism of Short-Circuit Oscillations in Automotive-Grade Multi-Chip Parallel Power Modules and an Effective Mitigation Approach
This paper presents an in-depth analysis of the oscillation phenomenon occurring in multi-chip parallel automotive-grade power modules under short-circuit conditions and investigates three suppression methods. We tested and analyzed two commercial automotive-grade power modules, one containing two chips and the other containing a single chip, and found that short-circuit gate oscillations were more likely to occur in multi-chip parallel packaged modules than in single-chip packaged modules. Through experimental and simulation analyses, we observed that gate oscillations were mainly caused by the interaction between internal parasitic parameters of the module and the external drive circuit, and we found that high drive resistance and low common emitter inductance between parallel chips could effectively suppress gate voltage oscillations. We also analyzed the two mainstream suppression schemes, increasing the drive gate resistance and placing the drive capacitors in parallel. Unfortunately, we found that these suppression schemes were not ideal solutions because both schemes changed the switching characteristics of the power module. As an alternative, we propose a simple and effective solution that involves adding parallel connections between the parallel chips. Simulation calculations showed that this optimized method reduced the emitter inductance between parallel chips in the upper bridge arm by about 30% and in the lower bridge arm by 35%. Through short-circuit experiments conducted at different DC bus voltages, it has been verified that the new optimized solution effectively resolves gate oscillation issues without affecting the switching characteristics of the power module.
- Open Access
- 30 August 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (9) , 1695
Failure Analysis for Gold Wire Bonding of Sensor Packaging Based on Experimental and Numerical Methods
There is an increasing demand for the use of automotive sensors where complex working environments may easily lead to failure. Wire pull and shear test models based on finite-element analysis are established to evaluate their reliability by investigating the failure mode and mechanism of gold wire bonding. The effect of shear force position and pull force position on failure is also analyzed. The bonding failure was verified by experiments, which is consistent with the simulation result. The results show that: (1) The three-dimensional quantitative modeling reveals the process of bonding delamination and stress concentration. (2) The bonding–slip method (BSM) is adopted in the gold ball detaching process. The concept of three states, including deformation accumulation, cracking, and disengagement, was put forward to reveal the interface stress evolution trend according to the shear testing results. The results indicate that in the interface, the stress in the deformation accumulation state decreases from the tensile side (or compression side) to the center, and the stress in the cracking and disengagement states reduces gradually from the tensile side to the edge. When the interface is completely separated, the failed shear force concentrates on 42 g. The concept and theory proposed in this work can effectively reveal the failure mechanism of bonding interface and help to establish a new failure criterion.
- 30 August 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (9) , 1695
Open AccessFailure Analysis for Gold Wire Bonding of Sensor Packaging Based on Experimental and Numerical Methods
There is an increasing demand for the use of automotive sensors where complex working environments may easily lead to failure. Wire pull and shear test models based on finite-element analysis are established to evaluate their reliability by investigating the failure mode and mechanism of gold wire bonding. The effect of shear force position and pull force position on failure is also analyzed. The bonding failure was verified by experiments, which is consistent with the simulation result. The results show that: (1) The three-dimensional quantitative modeling reveals the process of bonding delamination and stress concentration. (2) The bonding–slip method (BSM) is adopted in the gold ball detaching process. The concept of three states, including deformation accumulation, cracking, and disengagement, was put forward to reveal the interface stress evolution trend according to the shear testing results. The results indicate that in the interface, the stress in the deformation accumulation state decreases from the tensile side (or compression side) to the center, and the stress in the cracking and disengagement states reduces gradually from the tensile side to the edge. When the interface is completely separated, the failed shear force concentrates on 42 g. The concept and theory proposed in this work can effectively reveal the failure mechanism of bonding interface and help to establish a new failure criterion.
- Open Access
A Micromechanical Analysis to the Viscoplastic Behavior of Sintered Silver Joints under Shear Loading
Ag paste has been recognized as a promising substitute for Sn/Pb solder in SiC or GaN power electronic devices, owing to its ability to withstand high temperatures and facilitate low-temperature packing. The reliability of these high-power circuits is greatly influenced by the mechanical properties of sintered Ag paste. However, there exist substantial voids inside the sintered silver layer after sintering, and the conventional macroscopic constitutive models have certain limitation to describe the shear stress–strain relationship of sintered silver materials. To analyze the void evolution and microstructure of sintered silver, Ag composite pastes composed of micron flake silver and nano-silver particles were prepared. The mechanical behaviors were studied at different temperatures (0–125 °C) and strain rates (1 × 10−4–1 × 10−2) for Ag composite pastes. The crystal plastic finite element method (CPFEM) was developed to describe the microstructure evolution and shear behaviors of sintered silver at varied strain rates and ambient temperatures. The model parameters were obtained by fitting experimental shear test data to a representative volume element (RVE) model built on representative volume elements, also known as Voronoi tessellations. The numerical predictions were compared with the experimental data, which showed that the introduced crystal plasticity constitutive model can describe the shear constitutive behavior of a sintered silver specimen with reasonable accuracy.
Open AccessA Micromechanical Analysis to the Viscoplastic Behavior of Sintered Silver Joints under Shear Loading
Ag paste has been recognized as a promising substitute for Sn/Pb solder in SiC or GaN power electronic devices, owing to its ability to withstand high temperatures and facilitate low-temperature packing. The reliability of these high-power circuits is greatly influenced by the mechanical properties of sintered Ag paste. However, there exist substantial voids inside the sintered silver layer after sintering, and the conventional macroscopic constitutive models have certain limitation to describe the shear stress–strain relationship of sintered silver materials. To analyze the void evolution and microstructure of sintered silver, Ag composite pastes composed of micron flake silver and nano-silver particles were prepared. The mechanical behaviors were studied at different temperatures (0–125 °C) and strain rates (1 × 10−4–1 × 10−2) for Ag composite pastes. The crystal plastic finite element method (CPFEM) was developed to describe the microstructure evolution and shear behaviors of sintered silver at varied strain rates and ambient temperatures. The model parameters were obtained by fitting experimental shear test data to a representative volume element (RVE) model built on representative volume elements, also known as Voronoi tessellations. The numerical predictions were compared with the experimental data, which showed that the introduced crystal plasticity constitutive model can describe the shear constitutive behavior of a sintered silver specimen with reasonable accuracy.