May Yam Moshkovitz Douvdevany
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
May Yam Moshkovitz Douvdevany has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Shlomo Magdassi
The Hebrew University of Jerusalem
4 shared publications - Alice Zanini
Department of Industrial Engineering, University of Padova, via Marzolo 9, Padova 35131, Italy
1 shared publication - Andrea Ottomaniello
Center For Materials Interfaces Istituto Italiano di Tecnologia (IIT) Pontedera Italy
1 shared publication Danielle Paz
Institute of Chemistry The Hebrew University of Jerusalem Jerusalem 9190401 Israel
1 shared publicationDaria Savraeva
1 shared publication- Daria Savraeva
Casali Center for Applied Chemistry, Institute of Chemistry, The Hebrew University of Jerusalem, Jerusalem, Israel
1 shared publication
Latest Publications
- 16 November 2026
- Published by Wiley in Israel Journal of Chemistry
- Vol. 66 (6)
3D‐Printed ZnO Nanoparticle‐Based Nanocomposite for Photocatalytic Water Purification
Treatment of contaminated water is essential for removing harmful pollutants, pathogens, and toxic substances. Modern treatment processes improve water quality and support sustainable water reuse. However, challenges such as high treatment costs, emerging contaminants, and increasing industrial and urban wastewater volumes continue to hinder effective management. Herein, low‐cost, 3D‐printable photoactive filters have been demonstrated made from photoactive ZnO nanorods (NRs). These dual‐functioning ZnO NRs act as quantum photoinitiators for digital light processing 3D printing, while also providing the post‐cured polymer with photocatalytic functionalities. Using 3D printing, intricate photoactive filters can be fabricated with high surface area, offering a relevant mobile solution for wastewater remediation by harnessing light energy to degrade pollutants. The effects of ZnO nanoparticle concentration, the ink composition, and the filtering system design were studied. These nanocomposites achieved over 80% degradation of methylene blue, demonstrating good photocatalytic activity. This indicates the potential for sustainable and environmentally friendly water treatment applications.
- 16 November 2026
- Published by Wiley in Israel Journal of Chemistry
- Vol. 66 (6)
3D‐Printed ZnO Nanoparticle‐Based Nanocomposite for Photocatalytic Water Purification
Treatment of contaminated water is essential for removing harmful pollutants, pathogens, and toxic substances. Modern treatment processes improve water quality and support sustainable water reuse. However, challenges such as high treatment costs, emerging contaminants, and increasing industrial and urban wastewater volumes continue to hinder effective management. Herein, low‐cost, 3D‐printable photoactive filters have been demonstrated made from photoactive ZnO nanorods (NRs). These dual‐functioning ZnO NRs act as quantum photoinitiators for digital light processing 3D printing, while also providing the post‐cured polymer with photocatalytic functionalities. Using 3D printing, intricate photoactive filters can be fabricated with high surface area, offering a relevant mobile solution for wastewater remediation by harnessing light energy to degrade pollutants. The effects of ZnO nanoparticle concentration, the ink composition, and the filtering system design were studied. These nanocomposites achieved over 80% degradation of methylene blue, demonstrating good photocatalytic activity. This indicates the potential for sustainable and environmentally friendly water treatment applications.
- Open Access
- 30 March 2026
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 118 (1) , 22
Additive manufacturing of zirconia‑stabilized silica-phosphate glasses from sol-gel-based photocurable inks
Transparent, rare-earth-doped silica-based glasses are promising candidates for photonic and laser applications due to their favorable optical properties. Here, we report the fabrication of three-dimensional silica-phosphate and silica-zirconia-phosphate (Nd³⁺-doped) glasses, using a sol-gel-derived, particle-free photocurable resin that is tailored for digital light processing (DLP) 3D printing and UV-assisted mold casting. The resin consists solely of sol-gel precursors and a dual photopolymerizable component, enabling high-resolution printing without particle dispersion. Following room-temperature aging and a short thermal treatment at 700 °C for 1 h, transparent, crack-free glasses were obtained. The resulting glass structures exhibited transmittance values of 76.2 ± 0.3% and 77.1 ± 0.2% at 680 nm and 850 nm, respectively, and retained an amorphous microstructure. Phosphate incorporation improved the distribution of Nd³⁺ ions and suppressed photoluminescence (PL) quenching, but partial phosphate loss occurred during sintering. The addition of zirconia effectively stabilizes the phosphate within the silica network, preserving the composition of the printing solution. Phosphate addition led to a pronounced enhancement of PL intensity, up to tenfold for the 92SiO₂-4P₂O₅-4ZrO₂ composition doped with 0.7 mol % Nd₂O₃, compared to phosphate-free glass (96SiO₂-4ZrO₂). This facile and combined photopolymerization and the sol-gel-based DLP printing process enable the fabrication of geometrically complex, compositionally tunable, transparent laser glasses, demonstrating a cost-effective route for developing custom photonic and optoelectronic components.
- 30 March 2026
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 118 (1) , 22
Open AccessAdditive manufacturing of zirconia‑stabilized silica-phosphate glasses from sol-gel-based photocurable inks
Transparent, rare-earth-doped silica-based glasses are promising candidates for photonic and laser applications due to their favorable optical properties. Here, we report the fabrication of three-dimensional silica-phosphate and silica-zirconia-phosphate (Nd³⁺-doped) glasses, using a sol-gel-derived, particle-free photocurable resin that is tailored for digital light processing (DLP) 3D printing and UV-assisted mold casting. The resin consists solely of sol-gel precursors and a dual photopolymerizable component, enabling high-resolution printing without particle dispersion. Following room-temperature aging and a short thermal treatment at 700 °C for 1 h, transparent, crack-free glasses were obtained. The resulting glass structures exhibited transmittance values of 76.2 ± 0.3% and 77.1 ± 0.2% at 680 nm and 850 nm, respectively, and retained an amorphous microstructure. Phosphate incorporation improved the distribution of Nd³⁺ ions and suppressed photoluminescence (PL) quenching, but partial phosphate loss occurred during sintering. The addition of zirconia effectively stabilizes the phosphate within the silica network, preserving the composition of the printing solution. Phosphate addition led to a pronounced enhancement of PL intensity, up to tenfold for the 92SiO₂-4P₂O₅-4ZrO₂ composition doped with 0.7 mol % Nd₂O₃, compared to phosphate-free glass (96SiO₂-4ZrO₂). This facile and combined photopolymerization and the sol-gel-based DLP printing process enable the fabrication of geometrically complex, compositionally tunable, transparent laser glasses, demonstrating a cost-effective route for developing custom photonic and optoelectronic components.
- 13 December 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (51) , 70828-70838
Photocurable Sol–Gel Formulations for the Fabrication of Titanium Carbide/Carbon Nanocomposites via Digital Light Processing
Additive manufacturing of carbide materials has received significant attention in the past years due to the ability to fabricate complex structures over different length scales. However, the typical limitations for powder-laden inks, such as nozzle clogging, rheological and geometric constraints, particle sedimentation, light-scattering and absorbing phenomena, narrow the range of available processes to manufacture carbide materials via conventional particle-based systems. To address these shortcomings, we have developed a one-pot synthetic route for the preparation of sol-gel-based UV-photocurable formulations, aiming at the fabrication of titanium carbide/carbon nanocomposites using digital light processing printing, pointing to potential applications in the field of nuclear physics. Carbides have attracted increasing interest as a target material for the production of radioisotopes in the ISOL facilities; however, the release of radioisotopes strictly relies on the presence of open porous structures, thus enhancing the diffusion and effusion phenomena from the target component. Through our approach, we have successfully fabricated hierarchical porous structures of TiC with a high specific surface area. By controlling the positioning of the building blocks within the framework and the supramolecular interactions during the polymerization of the molecular precursors, we achieved multiscale structuring of the network with precise control over the local arrangement of the pores.
- 13 December 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (51) , 70828-70838
Photocurable Sol–Gel Formulations for the Fabrication of Titanium Carbide/Carbon Nanocomposites via Digital Light Processing
Additive manufacturing of carbide materials has received significant attention in the past years due to the ability to fabricate complex structures over different length scales. However, the typical limitations for powder-laden inks, such as nozzle clogging, rheological and geometric constraints, particle sedimentation, light-scattering and absorbing phenomena, narrow the range of available processes to manufacture carbide materials via conventional particle-based systems. To address these shortcomings, we have developed a one-pot synthetic route for the preparation of sol-gel-based UV-photocurable formulations, aiming at the fabrication of titanium carbide/carbon nanocomposites using digital light processing printing, pointing to potential applications in the field of nuclear physics. Carbides have attracted increasing interest as a target material for the production of radioisotopes in the ISOL facilities; however, the release of radioisotopes strictly relies on the presence of open porous structures, thus enhancing the diffusion and effusion phenomena from the target component. Through our approach, we have successfully fabricated hierarchical porous structures of TiC with a high specific surface area. By controlling the positioning of the building blocks within the framework and the supramolecular interactions during the polymerization of the molecular precursors, we achieved multiscale structuring of the network with precise control over the local arrangement of the pores.
- 28 August 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 92
Additive manufacturing of transparent conductive indium tin oxide by sol-gel and multiphoton absorption polymerization
- 28 August 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 92
Additive manufacturing of transparent conductive indium tin oxide by sol-gel and multiphoton absorption polymerization
- Open Access
- 17 June 2023
- Published by Wiley in Advanced Materials Technologies
- Vol. 8 (23)
3D Printing Transparent γ‐Alumina Porous Structures Based on Photopolymerizable Sol–Gel Inks
A novel method for fabricating transparent porous γ‐alumina 3D structures by printing at high resolution is presented. The process is based on combining digital light processing 3D printing (DLP) and sol–gel reactions, all performed in transparent solutions, resulting in ceramic monolithic porous structures. The aqueous printing solution contains mainly aluminum chloride, propylene oxide (PO), ethanol, and acrylic acid (AA). The printed polymerized structures are aged, followed by supercritical drying (SCD), and sintered at high temperatures. During aging and sintering, the printed objects shrink, thus enabling a final printing resolution far beyond the nominal value of the used printer. The resulting structures are crystalline γ‐Al2O3, with a very high surface area, above 1800 m2 g−1, and optical transmission above 80% at 600 nm. In addition, SCD enables precise control of pores’ dimensions and total surface area, which are essential for applications including thermal insulation and catalyst support and for obtaining heat‐resistant transparent optical devices.
- 17 June 2023
- Published by Wiley in Advanced Materials Technologies
- Vol. 8 (23)
Open Access3D Printing Transparent γ‐Alumina Porous Structures Based on Photopolymerizable Sol–Gel Inks
A novel method for fabricating transparent porous γ‐alumina 3D structures by printing at high resolution is presented. The process is based on combining digital light processing 3D printing (DLP) and sol–gel reactions, all performed in transparent solutions, resulting in ceramic monolithic porous structures. The aqueous printing solution contains mainly aluminum chloride, propylene oxide (PO), ethanol, and acrylic acid (AA). The printed polymerized structures are aged, followed by supercritical drying (SCD), and sintered at high temperatures. During aging and sintering, the printed objects shrink, thus enabling a final printing resolution far beyond the nominal value of the used printer. The resulting structures are crystalline γ‐Al2O3, with a very high surface area, above 1800 m2 g−1, and optical transmission above 80% at 600 nm. In addition, SCD enables precise control of pores’ dimensions and total surface area, which are essential for applications including thermal insulation and catalyst support and for obtaining heat‐resistant transparent optical devices.