Albina M. Murashko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Albina M. Murashko has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Olga V. Boytsova
Department of Chemistry, Lomonosov Moscow State University, Building, 3, Leninskie Gory, 1, 119991 Moscow, Russia
7 shared publications - Tatiana B. Shatalova
Department of Chemistry, Lomonosov Moscow State University, Building, 3, Leninskie Gory, 1, 119991 Moscow, Russia
7 shared publications - Tatiana Viktorovna Safronova
Department of Chemistry, Lomonosov Moscow State University, Building, 3, Leninskie Gory, 1, 119991 Moscow, Russia
7 shared publications - Yaroslav Filippov
Department of Materials Science, Lomonosov Moscow State University, Building, 73, Leninskie Gory, 1, 119991 Moscow, Russia
6 shared publications - Tatiana V. Filippova
Department of Chemistry, Lomonosov Moscow State University, Building, 3, Leninskie Gory, 1, 119991 Moscow, Russia
5 shared publications - Vadim Platonov
Department of Chemistry, Lomonosov Moscow State University, Building, 3, Leninskie Gory, 1, 119991 Moscow, Russia
5 shared publications
Latest Publications
- Open Access
- 26 October 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (11) , 565
Freeze-Dried Porous Composites Based on Sodium Alginate and Powders of Calcium Salts Synthesized from Mixed-Anionic Solutions Prepared from (NH4)2CO3 and (NH4)2H2P2O7 Taken in Different Proportions
The creation of new biocompatible and resorbable composite materials with an alginate matrix and fine synthetic calcium salts as a filler for potential applications in regenerative medicine is an important area of materials science. Freeze-dried porous (0.05–0.06 g/cm3) composite materials were prepared from homogeneous molding compositions containing distilled water (95 wt. %), fine inorganic powders of calcium salts (2.5 wt. %), and sodium alginate (2.5 wt. %). An aqueous solution of calcium chloride (CaCl2) and an aqueous mixed-anionic solution, which were prepared by mixing solutions of (NH4)2CO3 and (NH4)2H2P2O7 taken in different proportions, were used for syntheses of fine inorganic powders. The molar ratios (NH4)2H2P2O7)/((NH4)2CO3+(NH4)2H2P2O7) of salts used for mixed-anionic solutions preparation were established as 0 (reference powder), 0.02, 0.04, 0.08 and 0.16. Quantities of aqueous solutions of calcium chloride (CaCl2) were taken to provide a molar ratio CaCl2/((NH4)2CO3+(NH4)2H2P2O7) equal to 1.00 (reference powder), 1.02, 1.04, 1.08 and 1.16. The phase composition of synthesized inorganic powders included calcium carbonate (CaCO3) (mostly vaterite) and a quasi-amorphous phase of calcium phosphates (primarily hydrated calcium pyrophosphate (Ca2P2O7 xH2O)). All synthesized powders contained adsorbed and occluded salts present in the mother liquor after synthesis was completed, before separation of the precipitate. The mother liquors were aqueous solutions of ammonium chloride (NH4Cl) (all syntheses) and calcium chloride (CaCl2) (syntheses from mixed-anionic solutions). As components of inorganic powders used as fillers in the composite materials, ammonium chloride (NH4Cl) and calcium chloride (CaCl2) provoked a partial cross-linking of sodium alginate in the stages of preparation of molding compositions, composite samples molding, freezing, and freeze-drying. All freeze-dried porous composite materials demonstrated a high water absorption capacity of 4600–9200%. The most pronounced cross-linked effect was observed for alginate matrices loaded with powders synthesized at molar ratios CaCl2/((NH4)2CO3+(NH4)2H2P2O7) equal to 1.04 and 1.08, demonstrating the lowest water absorption and dry mass loss after dipping in distilled water for 12 h. Prepared freeze-dried porous composite materials with an alginate matrix and calcium carbonate and/or quasi-amorphous phase of calcium phosphates (primarily hydrated calcium pyrophosphate) powders, used as a filler, can be recommended for subsequent testing as an extracellular matrix for soft/hard tissue repair, as wound dressings or bone defect fillers.
- 26 October 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (11) , 565
Open AccessFreeze-Dried Porous Composites Based on Sodium Alginate and Powders of Calcium Salts Synthesized from Mixed-Anionic Solutions Prepared from (NH4)2CO3 and (NH4)2H2P2O7 Taken in Different Proportions
The creation of new biocompatible and resorbable composite materials with an alginate matrix and fine synthetic calcium salts as a filler for potential applications in regenerative medicine is an important area of materials science. Freeze-dried porous (0.05–0.06 g/cm3) composite materials were prepared from homogeneous molding compositions containing distilled water (95 wt. %), fine inorganic powders of calcium salts (2.5 wt. %), and sodium alginate (2.5 wt. %). An aqueous solution of calcium chloride (CaCl2) and an aqueous mixed-anionic solution, which were prepared by mixing solutions of (NH4)2CO3 and (NH4)2H2P2O7 taken in different proportions, were used for syntheses of fine inorganic powders. The molar ratios (NH4)2H2P2O7)/((NH4)2CO3+(NH4)2H2P2O7) of salts used for mixed-anionic solutions preparation were established as 0 (reference powder), 0.02, 0.04, 0.08 and 0.16. Quantities of aqueous solutions of calcium chloride (CaCl2) were taken to provide a molar ratio CaCl2/((NH4)2CO3+(NH4)2H2P2O7) equal to 1.00 (reference powder), 1.02, 1.04, 1.08 and 1.16. The phase composition of synthesized inorganic powders included calcium carbonate (CaCO3) (mostly vaterite) and a quasi-amorphous phase of calcium phosphates (primarily hydrated calcium pyrophosphate (Ca2P2O7 xH2O)). All synthesized powders contained adsorbed and occluded salts present in the mother liquor after synthesis was completed, before separation of the precipitate. The mother liquors were aqueous solutions of ammonium chloride (NH4Cl) (all syntheses) and calcium chloride (CaCl2) (syntheses from mixed-anionic solutions). As components of inorganic powders used as fillers in the composite materials, ammonium chloride (NH4Cl) and calcium chloride (CaCl2) provoked a partial cross-linking of sodium alginate in the stages of preparation of molding compositions, composite samples molding, freezing, and freeze-drying. All freeze-dried porous composite materials demonstrated a high water absorption capacity of 4600–9200%. The most pronounced cross-linked effect was observed for alginate matrices loaded with powders synthesized at molar ratios CaCl2/((NH4)2CO3+(NH4)2H2P2O7) equal to 1.04 and 1.08, demonstrating the lowest water absorption and dry mass loss after dipping in distilled water for 12 h. Prepared freeze-dried porous composite materials with an alginate matrix and calcium carbonate and/or quasi-amorphous phase of calcium phosphates (primarily hydrated calcium pyrophosphate) powders, used as a filler, can be recommended for subsequent testing as an extracellular matrix for soft/hard tissue repair, as wound dressings or bone defect fillers.
- Open Access
- 21 September 2026
- Published by MDPI AG in Preprints.org
Freeze-Dried Porous Composites Based on Sodium Alginate and Powders of Calcium Salts Synthesized from Mixed-Anionic Solutions Prepared from (NH4)2CO3 and (NH4)2H2P2O7 Taken in Different Proportions
Freeze-dried porous (0.05-0.06 g/cm3) composite materials were prepared from homogeneous molding compositions containing distilled water (95 wt. %), fine inorganic powders of calcium salts (2.5 wt. %) and sodium alginate (2.5 wt. %). Aqueous solution of calcium chloride (CaCl2) and aqueous mixed-anionic solution prepared by mixing solutions of (NH4)2CO3 and (NH4)2H2P2O7 taken in different proportions were used for syntheses of fine inorganic powders. Molar ratios (NH4)2Н2P2O7)/((NH4)2CO3+(NH4)2Н2P2O7) of salts used for mixed-anionic solutions preparation were established as 0 (reference powder), 0.02, 0.04, 0.08 and 0.16. Quantities of aqueous solutions of calcium chloride (CaCl2) was taken to provide molar ratio CaCl2/((NH4)2CO3+(NH4)2Н2P2O7) equal 1.00 (reference powder), 1.02, 1.04, 1.08 and 1.16. Phase composition of synthesized inorganic powders included calcium carbonate (CaCO3) (mostly vaterite) and quasi-amorphous phase of hydrated calcium pyrophosphate (Ca2P2O7 xH2O) . All synthesized powders contained adsorbed and occluded salts presented in the mother liquor after synthesis completed before separation of precipitate. Mother liquors were aqueous solutions of ammonium chloride (NH4Cl) (all syntheses) and calcium chloride (CaCl2) (syntheses from mixed-anionic solutions). As components of inorganic powders used as fillers in composite materials ammonium chloride (NH4Cl) and calcium chloride (CaCl2) provoked a partial cross-linking of sodium alginate in the stages of preparation of molding compositions, composite sample molding, freezing and freeze drying. All freeze-dried porous composite materials demonstrated high water absorption capacity 4700-9300%. The most pronounced cross-linked effect was observed for alginate matrixes loaded with powders synthesized at molar ratio CaCl2/((NH4)2CO3+(NH4)2Н2P2O7) equal 1.04 and 1.08 demonstrating lowest water absorption and dry mass-loss after dipping in distilled water for 12 hours. Prepared freeze-dried porous composite materials with alginate matrix and calcium carbonate and/or hydrated calcium pyrophosphate powders as a filler can be recommended for subsequent testing as extracellular matrix for soft/hard tissue repair, as wound dressings or bone defects fillers.
- 21 September 2026
- Published by MDPI AG in Preprints.org
Open AccessFreeze-Dried Porous Composites Based on Sodium Alginate and Powders of Calcium Salts Synthesized from Mixed-Anionic Solutions Prepared from (NH4)2CO3 and (NH4)2H2P2O7 Taken in Different Proportions
Freeze-dried porous (0.05-0.06 g/cm3) composite materials were prepared from homogeneous molding compositions containing distilled water (95 wt. %), fine inorganic powders of calcium salts (2.5 wt. %) and sodium alginate (2.5 wt. %). Aqueous solution of calcium chloride (CaCl2) and aqueous mixed-anionic solution prepared by mixing solutions of (NH4)2CO3 and (NH4)2H2P2O7 taken in different proportions were used for syntheses of fine inorganic powders. Molar ratios (NH4)2Н2P2O7)/((NH4)2CO3+(NH4)2Н2P2O7) of salts used for mixed-anionic solutions preparation were established as 0 (reference powder), 0.02, 0.04, 0.08 and 0.16. Quantities of aqueous solutions of calcium chloride (CaCl2) was taken to provide molar ratio CaCl2/((NH4)2CO3+(NH4)2Н2P2O7) equal 1.00 (reference powder), 1.02, 1.04, 1.08 and 1.16. Phase composition of synthesized inorganic powders included calcium carbonate (CaCO3) (mostly vaterite) and quasi-amorphous phase of hydrated calcium pyrophosphate (Ca2P2O7 xH2O) . All synthesized powders contained adsorbed and occluded salts presented in the mother liquor after synthesis completed before separation of precipitate. Mother liquors were aqueous solutions of ammonium chloride (NH4Cl) (all syntheses) and calcium chloride (CaCl2) (syntheses from mixed-anionic solutions). As components of inorganic powders used as fillers in composite materials ammonium chloride (NH4Cl) and calcium chloride (CaCl2) provoked a partial cross-linking of sodium alginate in the stages of preparation of molding compositions, composite sample molding, freezing and freeze drying. All freeze-dried porous composite materials demonstrated high water absorption capacity 4700-9300%. The most pronounced cross-linked effect was observed for alginate matrixes loaded with powders synthesized at molar ratio CaCl2/((NH4)2CO3+(NH4)2Н2P2O7) equal 1.04 and 1.08 demonstrating lowest water absorption and dry mass-loss after dipping in distilled water for 12 hours. Prepared freeze-dried porous composite materials with alginate matrix and calcium carbonate and/or hydrated calcium pyrophosphate powders as a filler can be recommended for subsequent testing as extracellular matrix for soft/hard tissue repair, as wound dressings or bone defects fillers.
- Open Access
- 23 March 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (3) , 172
Composite Materials Based on Sodium Alginate and Synthetic Powders of Calcium Carbonate
Properties of composite materials with polymer matrix and inorganic filler are affected by preparation methods and starting components’ properties. For example, filler powder particle size distribution, phase composition and presence/absence of dopants can greatly affect properties of resulting composites. The present research attempts to clarify the influence of synthetic CaCO3 powder properties on alginate/CaCO3 composite material preparation process. Composite materials in the form of granules, networks and films were created from suspensions of synthetic powders of calcium carbonates CaCO3 in aqueous solutions of sodium alginate. Powders of calcium carbonates CaCO3 were synthesized from 0.5 M aqueous solutions of calcium chloride CaCl2 and aqueous solutions of potassium K2CO3 (at molar ratio Ca/CO3 = 1), sodium Na2CO3 (at molar ratio Ca/CO3 = 1), and ammonium (NH4)2CO3 (at molar ratios Ca/CO3 = 1 and Ca/CO3 = 0.5) carbonates. Phase composition of powder synthesized from CaCl2 and K2CO3 was presented by calcite. Phase composition of powders synthesized from other soluble carbonates included calcite and vaterite. The powder preparation protocol excluded the stage of synthesized powder washing for by-product removal. This preparation protocol provided preservation of reaction by-product in the synthesized powder at a very low level. The presence of NH4Cl as a reaction by-product even in small quantities can be taken as a reason for visually observed subsequences of cross-linking reaction at the stage of suspensions preparation. Aqueous solution of sodium alginate and suspensions containing powders synthesized from potassium K2CO3 and sodium Na2CO3 carbonates demonstrated similar dependence of viscosities from shear rate. The presence of (NH4)2CO3 in the powder synthesized at molar ratio Ca/CO3 = 0.5 was the reason for the lower viscosity of the suspension in comparison with suspensions loaded with powders containing KCl, NaCl and (NH4)2Cl as reaction by-products due to decomposition of unstable (NH4)2CO3 and gas phase formation. The presence of (NH4)2Cl in the powder synthesized at molar ratio Ca/CO3 = 1 in contrast was a reason for the highest viscosity suspension in comparison with those under investigation. Additionally, (NH4)2Cl presence in synthetic powders shows the ability to facilitate partial dissolution of CaCO3 providing a higher concentration of Ca2+ cations at the stage of suspension preparation, thus aiding the cross-linking process of alginate hydrogel. Granules, meshes and films were created via interaction of suspensions of calcium carbonates CaCO3 in aqueous solutions of sodium alginate with 0.25 M aqueous solutions of calcium chloride CaCl2 to provide the formation of matrix of composites via Ca-crosslinking of sodium alginate followed by washing and freeze drying under deep vacuum. The created composite materials in the form of granules, meshes and films based on Ca-cross-linked alginate and powders of synthetic calcium carbonate can be recommended for skin wound and bone defect treatment and drug delivery carriers.
- 23 March 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (3) , 172
Open AccessComposite Materials Based on Sodium Alginate and Synthetic Powders of Calcium Carbonate
Properties of composite materials with polymer matrix and inorganic filler are affected by preparation methods and starting components’ properties. For example, filler powder particle size distribution, phase composition and presence/absence of dopants can greatly affect properties of resulting composites. The present research attempts to clarify the influence of synthetic CaCO3 powder properties on alginate/CaCO3 composite material preparation process. Composite materials in the form of granules, networks and films were created from suspensions of synthetic powders of calcium carbonates CaCO3 in aqueous solutions of sodium alginate. Powders of calcium carbonates CaCO3 were synthesized from 0.5 M aqueous solutions of calcium chloride CaCl2 and aqueous solutions of potassium K2CO3 (at molar ratio Ca/CO3 = 1), sodium Na2CO3 (at molar ratio Ca/CO3 = 1), and ammonium (NH4)2CO3 (at molar ratios Ca/CO3 = 1 and Ca/CO3 = 0.5) carbonates. Phase composition of powder synthesized from CaCl2 and K2CO3 was presented by calcite. Phase composition of powders synthesized from other soluble carbonates included calcite and vaterite. The powder preparation protocol excluded the stage of synthesized powder washing for by-product removal. This preparation protocol provided preservation of reaction by-product in the synthesized powder at a very low level. The presence of NH4Cl as a reaction by-product even in small quantities can be taken as a reason for visually observed subsequences of cross-linking reaction at the stage of suspensions preparation. Aqueous solution of sodium alginate and suspensions containing powders synthesized from potassium K2CO3 and sodium Na2CO3 carbonates demonstrated similar dependence of viscosities from shear rate. The presence of (NH4)2CO3 in the powder synthesized at molar ratio Ca/CO3 = 0.5 was the reason for the lower viscosity of the suspension in comparison with suspensions loaded with powders containing KCl, NaCl and (NH4)2Cl as reaction by-products due to decomposition of unstable (NH4)2CO3 and gas phase formation. The presence of (NH4)2Cl in the powder synthesized at molar ratio Ca/CO3 = 1 in contrast was a reason for the highest viscosity suspension in comparison with those under investigation. Additionally, (NH4)2Cl presence in synthetic powders shows the ability to facilitate partial dissolution of CaCO3 providing a higher concentration of Ca2+ cations at the stage of suspension preparation, thus aiding the cross-linking process of alginate hydrogel. Granules, meshes and films were created via interaction of suspensions of calcium carbonates CaCO3 in aqueous solutions of sodium alginate with 0.25 M aqueous solutions of calcium chloride CaCl2 to provide the formation of matrix of composites via Ca-crosslinking of sodium alginate followed by washing and freeze drying under deep vacuum. The created composite materials in the form of granules, meshes and films based on Ca-cross-linked alginate and powders of synthetic calcium carbonate can be recommended for skin wound and bone defect treatment and drug delivery carriers.
- Open Access
- 26 February 2026
- Published by MDPI AG in Preprints.org
Composite Materials Based on Sodium Alginate and Synthetic Powders of Calcium Carbonate
Composite materials in form of granules, networks and films were created from sus-pensions of synthetic powders of calcium carbonates CaCO3 in aqueous solutions of sodium alginate. Powders of calcium carbonates CaCO3 were synthesized from 0.5M aqueous solutions of calcium chloride CaCl2 and aqueous solutions of potassium K2CO3 (at molar ratio Ca/CO3=1), sodium Na2CO3 (at molar ratio Ca/CO3=1), ammonium (NH4)2CO3 (at molar ratios Ca/CO3=1 and Ca/CO3=0.5) carbonates. Phase composition of powder synthesized from CaCl2 and K2CO3 was presented by calcite. Phase compo-sition of powders synthesized from other soluble carbonates included calcite and va-terite. The powder preparation protocol excluded the stage of by-product removing via synthesized powder washing providing their preservation at very low level. Presence of NH4Cl as reaction by-product even in small quantities can be taken as a reason vis-ually observed subsequences of cross-linking reaction at the stage of suspensions preparation. Aqueous solution of sodium alginate and suspensions containing powders synthesized from potassium K2CO3 and sodium Na2CO3 carbonates demonstrated the similar dependence of viscosities from share rate. Presence of (NH4)2CO3 in the powder synthesized at molar ratio Ca/CO3=0.5 was the reason of the lower viscosity of the suspension in comparison with suspensions loaded with powders containing KCl, NaCl and (NH4)2Cl as reaction by-products due to decomposition of unstable (NH4)2CO3 and gas phase formation. Presence of (NH4)2Cl in the powder synthesized at molar ratio Ca/CO3=1 in contrary was a reason of the highest viscosity suspension comparison with those under investigation. Granules, meshes and films were created via interaction of suspensions calcium carbonates CaCO3 in aqueous solutions of so-dium alginate with 0.25M aqueous solutions of calcium chloride CaCl2 to provide formation of matrix of composites via Ca-crosslinking of sodium alginate followed by washing and freeze drying under deep vacuum. Created composite materials in form of granules, meshes and films based on Ca-cross-linked alginate and powders of synthetic calcium carbonate can be recommended for the skin wounds and bone defects treatment, and drug delivery carriers.
- 26 February 2026
- Published by MDPI AG in Preprints.org
Open AccessComposite Materials Based on Sodium Alginate and Synthetic Powders of Calcium Carbonate
Composite materials in form of granules, networks and films were created from sus-pensions of synthetic powders of calcium carbonates CaCO3 in aqueous solutions of sodium alginate. Powders of calcium carbonates CaCO3 were synthesized from 0.5M aqueous solutions of calcium chloride CaCl2 and aqueous solutions of potassium K2CO3 (at molar ratio Ca/CO3=1), sodium Na2CO3 (at molar ratio Ca/CO3=1), ammonium (NH4)2CO3 (at molar ratios Ca/CO3=1 and Ca/CO3=0.5) carbonates. Phase composition of powder synthesized from CaCl2 and K2CO3 was presented by calcite. Phase compo-sition of powders synthesized from other soluble carbonates included calcite and va-terite. The powder preparation protocol excluded the stage of by-product removing via synthesized powder washing providing their preservation at very low level. Presence of NH4Cl as reaction by-product even in small quantities can be taken as a reason vis-ually observed subsequences of cross-linking reaction at the stage of suspensions preparation. Aqueous solution of sodium alginate and suspensions containing powders synthesized from potassium K2CO3 and sodium Na2CO3 carbonates demonstrated the similar dependence of viscosities from share rate. Presence of (NH4)2CO3 in the powder synthesized at molar ratio Ca/CO3=0.5 was the reason of the lower viscosity of the suspension in comparison with suspensions loaded with powders containing KCl, NaCl and (NH4)2Cl as reaction by-products due to decomposition of unstable (NH4)2CO3 and gas phase formation. Presence of (NH4)2Cl in the powder synthesized at molar ratio Ca/CO3=1 in contrary was a reason of the highest viscosity suspension comparison with those under investigation. Granules, meshes and films were created via interaction of suspensions calcium carbonates CaCO3 in aqueous solutions of so-dium alginate with 0.25M aqueous solutions of calcium chloride CaCl2 to provide formation of matrix of composites via Ca-crosslinking of sodium alginate followed by washing and freeze drying under deep vacuum. Created composite materials in form of granules, meshes and films based on Ca-cross-linked alginate and powders of synthetic calcium carbonate can be recommended for the skin wounds and bone defects treatment, and drug delivery carriers.
- 19 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 16154-16168
Bioresorbable ceramics based on the Mg3(PO4)2–Mg2P2O7 system for bone tissue regeneration
- 19 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 16154-16168
Bioresorbable ceramics based on the Mg3(PO4)2–Mg2P2O7 system for bone tissue regeneration
- 1 January 2026
- Published by Intercontact Science in Perspektivnye Materialy
- No. 11
Investigation of the crystallization process in multielement systems based on 45S5 bioactive glass
The results of the synthesis of multicomponent glasses based on the base composition of Bioglass 45S5 are presented, which was modified by introducing up to 20 chemical elements to impart osteoinductive properties to the material. The multicomponent chemical composition of the glasses is determined by the specific role of each element in the biochemical processes accompanying the natural process of bone remodeling. An analysis of the glass transition and crystallization processes of the modified glasses was carried out, and the stable and metastable phases formed depending on the composition were established. The operating temperature range for softened glass becomes narrower for multielement glasses and shifts to a lower temperature range, which is naturally associated with a greater fragmentation of the silicon‑oxygen network in the modified glasses. An analysis of the sintering of glass powders indicates a two‑stage shrinkage process, with the first stage attributed to the transition of the glass to a viscous flow state, and the second stage to phase separation and the onset of crystallization. The obtained results demonstrate that multicomponent glasses can serve as a basis for the development of osteoinductive glass‑ceramic materials suitable for the fabrication of three‑dimensional porous scaffolds in bone tissue engineering.
- 1 January 2026
- Published by Intercontact Science in Perspektivnye Materialy
- No. 11
Investigation of the crystallization process in multielement systems based on 45S5 bioactive glass
The results of the synthesis of multicomponent glasses based on the base composition of Bioglass 45S5 are presented, which was modified by introducing up to 20 chemical elements to impart osteoinductive properties to the material. The multicomponent chemical composition of the glasses is determined by the specific role of each element in the biochemical processes accompanying the natural process of bone remodeling. An analysis of the glass transition and crystallization processes of the modified glasses was carried out, and the stable and metastable phases formed depending on the composition were established. The operating temperature range for softened glass becomes narrower for multielement glasses and shifts to a lower temperature range, which is naturally associated with a greater fragmentation of the silicon‑oxygen network in the modified glasses. An analysis of the sintering of glass powders indicates a two‑stage shrinkage process, with the first stage attributed to the transition of the glass to a viscous flow state, and the second stage to phase separation and the onset of crystallization. The obtained results demonstrate that multicomponent glasses can serve as a basis for the development of osteoinductive glass‑ceramic materials suitable for the fabrication of three‑dimensional porous scaffolds in bone tissue engineering.
- Open Access
Powders Synthesized from Calcium Chloride and Mixed-Anionic Solution Containing Orthophosphate and Carbonate Ions
Low-crystalline hydroxyapatite was synthesized from an aqueous solution of calcium chloride (CaCl2), and a mixed-anionic (HPO42− и CO32−) aqueous solution prepared from potassium hydrophosphate trihydrate (K2HPO4 3Н2О), and potassium carbonate (K2CO3). The interaction of K2CO3 and K2HPO4 salts during synthesis from a mixed-anionic solution in the reaction zone without additional regulation provided the pH level necessary for the synthesis of hydroxyapatite. For comparison, as references, powders were also synthesized from an aqueous solution of CaCl2 and from aqueous solutions of either K2HPO4 or K2CO3. The phase composition of the powder synthesized from aqueous solutions of CaCl2 and K2HPO4 included brushite (CaНРО4·2H2O). The phase composition of the powder synthesized from aqueous solutions of CaCl2 and K2CO3 included calcite (CaCO3). The phase composition of all synthesized powders contained potassium chloride (sylvine, KCl), as a reaction by-product. After heat treatment at 1000 °C of the powder containing low-crystalline hydroxyapatite and KCl, powder of chlorapatite (Са10(РО4)6Cl2) was obtained. After heat treatment of a powder containing brushite (CaНРО4·2H2O) and KCl at 800 and 1000 °C, a powder with the phase composition including β-calcium pyrophosphate (β-Ca2P2O7), β-calcium orthophosphate (β-Ca3(PO4)2), and potassium-calcium pyrophosphate (K2CaP2O7) was obtained. Heat treatment of calcite (CaCO3) powder at 800 °C, as expected, led to the formation of calcium oxide (CaO). Synthesized powders, including biocompatible minerals such as hydroxyapatite, chlorapatite, brushite, monetite, calcium pyrophosphate, calcium potassium pyrophosphate, tricalcium phosphate, and calcite, can be used for the creation of biocompatible inorganic materials or composite materials with a biocompatible polymer matrix. The potassium chloride present in the synthesized powders can act as one of the precursors of biocompatible minerals, such as chlorapatite or calcium potassium pyrophosphate, or it can be treated as a removable inorganic porogen.
Open AccessPowders Synthesized from Calcium Chloride and Mixed-Anionic Solution Containing Orthophosphate and Carbonate Ions
Low-crystalline hydroxyapatite was synthesized from an aqueous solution of calcium chloride (CaCl2), and a mixed-anionic (HPO42− и CO32−) aqueous solution prepared from potassium hydrophosphate trihydrate (K2HPO4 3Н2О), and potassium carbonate (K2CO3). The interaction of K2CO3 and K2HPO4 salts during synthesis from a mixed-anionic solution in the reaction zone without additional regulation provided the pH level necessary for the synthesis of hydroxyapatite. For comparison, as references, powders were also synthesized from an aqueous solution of CaCl2 and from aqueous solutions of either K2HPO4 or K2CO3. The phase composition of the powder synthesized from aqueous solutions of CaCl2 and K2HPO4 included brushite (CaНРО4·2H2O). The phase composition of the powder synthesized from aqueous solutions of CaCl2 and K2CO3 included calcite (CaCO3). The phase composition of all synthesized powders contained potassium chloride (sylvine, KCl), as a reaction by-product. After heat treatment at 1000 °C of the powder containing low-crystalline hydroxyapatite and KCl, powder of chlorapatite (Са10(РО4)6Cl2) was obtained. After heat treatment of a powder containing brushite (CaНРО4·2H2O) and KCl at 800 and 1000 °C, a powder with the phase composition including β-calcium pyrophosphate (β-Ca2P2O7), β-calcium orthophosphate (β-Ca3(PO4)2), and potassium-calcium pyrophosphate (K2CaP2O7) was obtained. Heat treatment of calcite (CaCO3) powder at 800 °C, as expected, led to the formation of calcium oxide (CaO). Synthesized powders, including biocompatible minerals such as hydroxyapatite, chlorapatite, brushite, monetite, calcium pyrophosphate, calcium potassium pyrophosphate, tricalcium phosphate, and calcite, can be used for the creation of biocompatible inorganic materials or composite materials with a biocompatible polymer matrix. The potassium chloride present in the synthesized powders can act as one of the precursors of biocompatible minerals, such as chlorapatite or calcium potassium pyrophosphate, or it can be treated as a removable inorganic porogen.
- Open Access
- 1 September 2025
- Published by MDPI AG in Preprints.org
Powders Synthesized from Calcium Chloride and Mixed-Anionic Solution Containing Orthophosphate and Carbonate Ions
Low crystalline hydroxyapatite was synthesized from an aqueous solution of calcium chloride CaCl2 and a mixed-anionic (HPO42- и CO32-) aqueous solution prepared from potassium hydro-phosphate trihydrate K2HPO4 3Н2О and potassium carbonate K2CO3. The interaction of K2CO3 and K2HPO4 salts during synthesis from a mixed anionic solution in the reaction zone without additional regulation provided the pH level necessary for the synthesis of hydroxyapatite. For comparison, as references, powders were also synthesized from an aqueous solution of calcium chloride CaCl2 and from aqueous solutions of either potassium hydrophosphate K2HPO4 or potassium carbonate K2CO3. The phase composition of the powder synthesized from aqueous solutions of calcium chlo-ride CaCl2 and potassium hydrophosphate K2HPO4 included brushite CaНРО4·2H2O. The phase composition of the powder synthesized from aqueous solutions of calcium chloride CaCl2 and po-tassium carbonate K2CO3 included calcite CaCO3. The phase composition of all synthesized pow-ders contained potassium chloride (sylvine) KCl as a reaction by-product. After heat treatment at 1000 °C of the powder containing low crystalline hydroxyapatite and potassium chloride (sylvine) KCl, powder of chlorapatite Са10(РО4)6Cl2 was obtained. After heat treatment of a powder con-taining brushite CaНРО4·2H2O and potassium chloride (sylvine) KCl at 800 and 1000 °C, a powder with the phase composition including β-calcium pyrophosphate β-Ca2P2O7, β-calcium ortho-phosphate β-Ca3(PO4)2 and potassium-calcium pyrophosphate K2CaP2O7 was obtained. Heat treatment of calcite CaCO3 powder at 800 °C, as expected, led to the formation of calcium oxide CaO. Synthesized powders including biocompatible minerals such as hydroxyapatite, chlorapatite, brushite, monetite, calcium pyrophosphate, calcium potassium pyrophosphate, tricalcium phos-phate, calcite can be used for creation of biocompatible inorganic materials or composite materials with a biocompatible polymer matrix. The potassium chloride present in the synthesized powders can act as one of the precursors of biocompatible minerals such as chlorapatite or calcium potassium pyrophosphate; or it can be treated as a removable inorganic porogen.
- 1 September 2025
- Published by MDPI AG in Preprints.org
Open AccessPowders Synthesized from Calcium Chloride and Mixed-Anionic Solution Containing Orthophosphate and Carbonate Ions
Low crystalline hydroxyapatite was synthesized from an aqueous solution of calcium chloride CaCl2 and a mixed-anionic (HPO42- и CO32-) aqueous solution prepared from potassium hydro-phosphate trihydrate K2HPO4 3Н2О and potassium carbonate K2CO3. The interaction of K2CO3 and K2HPO4 salts during synthesis from a mixed anionic solution in the reaction zone without additional regulation provided the pH level necessary for the synthesis of hydroxyapatite. For comparison, as references, powders were also synthesized from an aqueous solution of calcium chloride CaCl2 and from aqueous solutions of either potassium hydrophosphate K2HPO4 or potassium carbonate K2CO3. The phase composition of the powder synthesized from aqueous solutions of calcium chlo-ride CaCl2 and potassium hydrophosphate K2HPO4 included brushite CaНРО4·2H2O. The phase composition of the powder synthesized from aqueous solutions of calcium chloride CaCl2 and po-tassium carbonate K2CO3 included calcite CaCO3. The phase composition of all synthesized pow-ders contained potassium chloride (sylvine) KCl as a reaction by-product. After heat treatment at 1000 °C of the powder containing low crystalline hydroxyapatite and potassium chloride (sylvine) KCl, powder of chlorapatite Са10(РО4)6Cl2 was obtained. After heat treatment of a powder con-taining brushite CaНРО4·2H2O and potassium chloride (sylvine) KCl at 800 and 1000 °C, a powder with the phase composition including β-calcium pyrophosphate β-Ca2P2O7, β-calcium ortho-phosphate β-Ca3(PO4)2 and potassium-calcium pyrophosphate K2CaP2O7 was obtained. Heat treatment of calcite CaCO3 powder at 800 °C, as expected, led to the formation of calcium oxide CaO. Synthesized powders including biocompatible minerals such as hydroxyapatite, chlorapatite, brushite, monetite, calcium pyrophosphate, calcium potassium pyrophosphate, tricalcium phos-phate, calcite can be used for creation of biocompatible inorganic materials or composite materials with a biocompatible polymer matrix. The potassium chloride present in the synthesized powders can act as one of the precursors of biocompatible minerals such as chlorapatite or calcium potassium pyrophosphate; or it can be treated as a removable inorganic porogen.
- Open Access
Powders Synthesized from Water Solutions of Sodium Silicate and Calcium and/or Magnesium Chlorides
Powders with phase composition including quasi-amorphous phases and calcium carbonate CaCO3 in the form of calcite or aragonite and sodium halite NaCl as a reaction by-product were synthesized from 0.5M aqua solutions of sodium silicate and 0.5M aqua solutions of calcium and/or magnesium chlorides. Starting solutions were taken in quantities which could provide precipitation of hydrated calcium and/or magnesium silicates with molar ratios Ca/Si = 1 (CaSi), Mg/Si = 1 (MgSi) or (Ca+Mg)/Si = 1 (CaMgSi). Hydrated calcium and/or magnesium silicates, hydrated silica, magnesium carbonate, hydrated magnesium carbonate or hydrated magnesium silicate containing carbonate ions are suspected as components of quasi-amorphous phases presented in synthesized powders. Heat treatment of synthesized powders at 400, 600, 800 °C and pressed preceramic samples at 900, 1000, 1100 and 1200 °C were used for investigation of thermal evolution of the phase composition and microstructure of powders and ceramic samples. Mass loss of powder samples under investigation during heat treatment was provided due to evacuation of H2O (m/z = 18), CO2 (m/z = 44) and NaCl at temperatures above its melting point. After sintering at 1100 °C, the phase composition of ceramic samples included wollastonite CaSiO3 (CaSi_1100); enstatite MgSiO3, clinoenstatite MgSiO3 and forsterite Mg2SiO4 (MgSi_1100); and diopside CaMgSi2O6 (CaMgSi_1100). After sintering at 1200 °C, the phase composition of ceramics CaSi_1200 included pseudo-wollastonite CaSiO3. After heat treatment at 1300 °C, the phase composition of MgSi_1300 powder included preferably protoenstatite MgSiO3. The phase composition of all samples after heat treatment belongs to the oxide system CaO–MgO–SiO2. Ceramic materials in this system are of interest for use in different areas, including refractories, construction materials and biomaterials. Powders prepared in the present investigation, both via precipitation and via heat treatment, can be used for the creation of materials with specific properties and in model experiments as lunar regolith simulants.
Open AccessPowders Synthesized from Water Solutions of Sodium Silicate and Calcium and/or Magnesium Chlorides
Powders with phase composition including quasi-amorphous phases and calcium carbonate CaCO3 in the form of calcite or aragonite and sodium halite NaCl as a reaction by-product were synthesized from 0.5M aqua solutions of sodium silicate and 0.5M aqua solutions of calcium and/or magnesium chlorides. Starting solutions were taken in quantities which could provide precipitation of hydrated calcium and/or magnesium silicates with molar ratios Ca/Si = 1 (CaSi), Mg/Si = 1 (MgSi) or (Ca+Mg)/Si = 1 (CaMgSi). Hydrated calcium and/or magnesium silicates, hydrated silica, magnesium carbonate, hydrated magnesium carbonate or hydrated magnesium silicate containing carbonate ions are suspected as components of quasi-amorphous phases presented in synthesized powders. Heat treatment of synthesized powders at 400, 600, 800 °C and pressed preceramic samples at 900, 1000, 1100 and 1200 °C were used for investigation of thermal evolution of the phase composition and microstructure of powders and ceramic samples. Mass loss of powder samples under investigation during heat treatment was provided due to evacuation of H2O (m/z = 18), CO2 (m/z = 44) and NaCl at temperatures above its melting point. After sintering at 1100 °C, the phase composition of ceramic samples included wollastonite CaSiO3 (CaSi_1100); enstatite MgSiO3, clinoenstatite MgSiO3 and forsterite Mg2SiO4 (MgSi_1100); and diopside CaMgSi2O6 (CaMgSi_1100). After sintering at 1200 °C, the phase composition of ceramics CaSi_1200 included pseudo-wollastonite CaSiO3. After heat treatment at 1300 °C, the phase composition of MgSi_1300 powder included preferably protoenstatite MgSiO3. The phase composition of all samples after heat treatment belongs to the oxide system CaO–MgO–SiO2. Ceramic materials in this system are of interest for use in different areas, including refractories, construction materials and biomaterials. Powders prepared in the present investigation, both via precipitation and via heat treatment, can be used for the creation of materials with specific properties and in model experiments as lunar regolith simulants.
- 1 January 2025
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 10
Study of mechanical properties of ceramic materials based on ca3(po4)2-ca2,5na(po4)2, obtained by 3d printing
The mechanical properties of ceramic materials based on high-temperature phases of tricalcium phosphate α-Ca3(PO4)2 and sodium rhenanite Ca2,5Na(PO4)2, as well as their composites in the 1:1 molar ratio, fabricated by the stereolithography method, have been studied. It is shown that the composite (biphase) ceramics produced by pressing followed by firing exhibit the highest density - 92% - and ultimate compression strength up to 120 MPa. For ceramic materials synthesized by 3D printing with a specified porosity of 70%, the influence of the pore space architecture on the mechanical properties under compression was determined. It is shown that ceramics with the Kelvin architecture exhibit greater strength than ceramics with the gyroid architecture. A temperature-time regime for heat treatment of the printed samples was developed to remove the polymer matrix, resulting in crack-free ceramics. It was found that the ultimate compressive strength of 3D ceramics based on α-Ca3(PO4)2 reached 2.5 MPa, which is acceptable for medical applications.
- 1 January 2025
- Published by Science & Technology in Deformation and Fracture of Materials
- No. 10
Study of mechanical properties of ceramic materials based on ca3(po4)2-ca2,5na(po4)2, obtained by 3d printing
The mechanical properties of ceramic materials based on high-temperature phases of tricalcium phosphate α-Ca3(PO4)2 and sodium rhenanite Ca2,5Na(PO4)2, as well as their composites in the 1:1 molar ratio, fabricated by the stereolithography method, have been studied. It is shown that the composite (biphase) ceramics produced by pressing followed by firing exhibit the highest density - 92% - and ultimate compression strength up to 120 MPa. For ceramic materials synthesized by 3D printing with a specified porosity of 70%, the influence of the pore space architecture on the mechanical properties under compression was determined. It is shown that ceramics with the Kelvin architecture exhibit greater strength than ceramics with the gyroid architecture. A temperature-time regime for heat treatment of the printed samples was developed to remove the polymer matrix, resulting in crack-free ceramics. It was found that the ultimate compressive strength of 3D ceramics based on α-Ca3(PO4)2 reached 2.5 MPa, which is acceptable for medical applications.