Murat Öztürk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Murat Öztürk has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Erdem Çiftçi
Gazi Üniversitesi
4 shared publications - Azim Doğuş Tuncer
Department of Energy Systems Engineering, Faculty of Engineering-Architecture, Burdur Mehmet Akif Ersoy University, Burdur, Turkey
2 shared publications - Ayça Altintaş
Mehmet Akif Ersoy Üniversitesi
1 shared publication - Berk Sürücü
Department of Energy Systems Engineering Mehmet Akif Ersoy University Burdur Turkey
1 shared publication - Fatma Kadriye Düden Örgen
Mehmet Akif Ersoy Üniversitesi
1 shared publication - Sezai Yaşar
Mehmet Akif Ersoy Üniversitesi
1 shared publication
Latest Publications
- 22 March 2024
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 9 (1) , 135-153
Numerical analysis of the journal bearings of Keban Hydroelectric Power Plant using different type nanofluids
Energy production in line with demand rapidly increases. Fossil fuel systems in use today pose a great threat to the future of the world and in this sense, the interest to the renewable energy sources such as hydroelectric energy systems is increasing. In this study, the heating problem of the journal bearings one of the parts of the hydroelectric energy systems was evaluated, various analysis were performed with the Computational Fluid Dynamics (CFD) approach to eliminate this problem and the results obtained were shared. Initial analyses were performed and evaluated for Mobil DTE 68 oil, which was commonly used as a refrigerant in journal bearings. Then, Al2O3 nanoparticles at concentrations of 3%, 7% and 10% were then added to the refrigerant oil and necessary analyses were performed for these three conditions. Finally, similar analyses were performed in the 3%, 7% and 10% concentration for SiO2. When the obtained temperature changes were examined accordingly, it was obtained that the increase in the concentration of nanoparticles exhibited a characteristic that was inversely proportional to the surface temperature. With the addition of nanoparticles, surface temperatures have been observed to decrease from 80°C to 68°C, but the effect on sharp corners is quite low. In this sense, it has been obtained that nanoparticles can significantly increase the thermal characteristics of Mobil DTE 68 oil, and it has been concluded that nanofluids may be an alternative solution for the overheating problem that occurs in journal bearings.
- 22 March 2024
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 9 (1) , 135-153
Numerical analysis of the journal bearings of Keban Hydroelectric Power Plant using different type nanofluids
Energy production in line with demand rapidly increases. Fossil fuel systems in use today pose a great threat to the future of the world and in this sense, the interest to the renewable energy sources such as hydroelectric energy systems is increasing. In this study, the heating problem of the journal bearings one of the parts of the hydroelectric energy systems was evaluated, various analysis were performed with the Computational Fluid Dynamics (CFD) approach to eliminate this problem and the results obtained were shared. Initial analyses were performed and evaluated for Mobil DTE 68 oil, which was commonly used as a refrigerant in journal bearings. Then, Al2O3 nanoparticles at concentrations of 3%, 7% and 10% were then added to the refrigerant oil and necessary analyses were performed for these three conditions. Finally, similar analyses were performed in the 3%, 7% and 10% concentration for SiO2. When the obtained temperature changes were examined accordingly, it was obtained that the increase in the concentration of nanoparticles exhibited a characteristic that was inversely proportional to the surface temperature. With the addition of nanoparticles, surface temperatures have been observed to decrease from 80°C to 68°C, but the effect on sharp corners is quite low. In this sense, it has been obtained that nanoparticles can significantly increase the thermal characteristics of Mobil DTE 68 oil, and it has been concluded that nanofluids may be an alternative solution for the overheating problem that occurs in journal bearings.
- Open Access
- 28 December 2023
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 11 (4) , 1162-1170
Değişken Sayıda Delikler İçeren Emici Plakalara Sahip Güneş Enerjili Hava Isıtıcısının Sayısal Analizi
Dünya nüfusundaki meydana gelen artışlar, enerjiye olan talepleri de doğrudan etkilemektedir. Nüfus artışı ile doğrudan etkilenen enerji taleplerine karşı tepki verebilmek ve sürdürülebilir bir gelecek sağlamak amacıyla farklı enerji kaynakları arayışları ortaya çıkmaktadır. Son zamanlarda popüler bir hale gelen yenilenebilir enerji kaynaklarının en temeli olan güneş enerjisinden elektrik üretimi ve ısıl uygulamalar ilerlemeye devam etmektedir. Bu çalışmada güneş enerjisinden ısıl enerji elde etmek amacıyla kullanılan güneş enerjili hava ısıtıcıların performansının arttırılması amaçlanmış ve farklı emici yüzeylere sahip güneş enerjili hava ısıtıcısı modelleri geliştirilmiştir. Geliştirilmiş olan bu modellerin analizleri Hesaplamalı Akışkanlar Dinamiği (HAD) yaklaşımı ile gerçekleştirilmiş ve sonuçlar değerlendirilmiştir. Başlangıçta geleneksel düz emici plakalı güneş enerjili hava ısıtıcısı modellenmiştir. Daha sonra düz plakaya sırasıyla 2, 4 ve 8 adet delikler eklenmiş ve aynı şartlar altında sistem analizleri gerçekleştirilmiştir. Yapılan bu analizler sonucu benzer oranlarda basınç düşüşleri görülmüş ve hava akış hızları oldukça yakın oranda azalmıştır. Bunun yanı sıra giriş ve çıkış noktası arasındaki sıcaklık farkları düz plakalı, 2 delikli, 4 delikli ve 8 delikli model için sırasıyla 12,6℃, 10℃, 13,5℃ ve 16,2℃ olarak elde edilmiştir. Elde edilen sonuçlara bağlı olarak delik sayısı ile sistem performansında arttığı ve oluşturulan deliklerin türbülans etkisi yaratarak ısı transferini önemli ölçüde iyileştirdiği gözlemlenmiştir.
- 28 December 2023
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 11 (4) , 1162-1170
Open AccessDeğişken Sayıda Delikler İçeren Emici Plakalara Sahip Güneş Enerjili Hava Isıtıcısının Sayısal Analizi
Dünya nüfusundaki meydana gelen artışlar, enerjiye olan talepleri de doğrudan etkilemektedir. Nüfus artışı ile doğrudan etkilenen enerji taleplerine karşı tepki verebilmek ve sürdürülebilir bir gelecek sağlamak amacıyla farklı enerji kaynakları arayışları ortaya çıkmaktadır. Son zamanlarda popüler bir hale gelen yenilenebilir enerji kaynaklarının en temeli olan güneş enerjisinden elektrik üretimi ve ısıl uygulamalar ilerlemeye devam etmektedir. Bu çalışmada güneş enerjisinden ısıl enerji elde etmek amacıyla kullanılan güneş enerjili hava ısıtıcıların performansının arttırılması amaçlanmış ve farklı emici yüzeylere sahip güneş enerjili hava ısıtıcısı modelleri geliştirilmiştir. Geliştirilmiş olan bu modellerin analizleri Hesaplamalı Akışkanlar Dinamiği (HAD) yaklaşımı ile gerçekleştirilmiş ve sonuçlar değerlendirilmiştir. Başlangıçta geleneksel düz emici plakalı güneş enerjili hava ısıtıcısı modellenmiştir. Daha sonra düz plakaya sırasıyla 2, 4 ve 8 adet delikler eklenmiş ve aynı şartlar altında sistem analizleri gerçekleştirilmiştir. Yapılan bu analizler sonucu benzer oranlarda basınç düşüşleri görülmüş ve hava akış hızları oldukça yakın oranda azalmıştır. Bunun yanı sıra giriş ve çıkış noktası arasındaki sıcaklık farkları düz plakalı, 2 delikli, 4 delikli ve 8 delikli model için sırasıyla 12,6℃, 10℃, 13,5℃ ve 16,2℃ olarak elde edilmiştir. Elde edilen sonuçlara bağlı olarak delik sayısı ile sistem performansında arttığı ve oluşturulan deliklerin türbülans etkisi yaratarak ısı transferini önemli ölçüde iyileştirdiği gözlemlenmiştir.
- 27 March 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (1) , 303-309
Software-Based Wind Energy Potential Assessment: A Case Study from Western Turkey
In this research, wind energy potential of a specific region in Western Turkey has been analyzed by using WindPRO software. The analyzed site is located in Ayvacık district of Çanakkale province of Turkey. Two types of wind energy turbines with 3 MW power including Enercon E-101/3000 and Nordex N117/3000 have been selected for the analyses. Weibull distribution has been utilized in the wind energy potential assessment. Also, average wind speed values and prevailing wind directions have been calculated for the selected locations in the analyzed region. The prevailing wind direction was determined for Enercon E-101/3000 and Nordex N117/3000 turbines as NNW and SSE, respectively. Estimated electrical energy generation values for Enercon E-101/3000 and Nordex N117/3000 turbines were obtained between 10177-11925 MWh/year and 9283-10954 MWh/year, respectively. Moreover, shape and scale parameters for each wind directions and annual energy generation values of each location have been calculated within the scope of this work.
- 27 March 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (1) , 303-309
Software-Based Wind Energy Potential Assessment: A Case Study from Western Turkey
In this research, wind energy potential of a specific region in Western Turkey has been analyzed by using WindPRO software. The analyzed site is located in Ayvacık district of Çanakkale province of Turkey. Two types of wind energy turbines with 3 MW power including Enercon E-101/3000 and Nordex N117/3000 have been selected for the analyses. Weibull distribution has been utilized in the wind energy potential assessment. Also, average wind speed values and prevailing wind directions have been calculated for the selected locations in the analyzed region. The prevailing wind direction was determined for Enercon E-101/3000 and Nordex N117/3000 turbines as NNW and SSE, respectively. Estimated electrical energy generation values for Enercon E-101/3000 and Nordex N117/3000 turbines were obtained between 10177-11925 MWh/year and 9283-10954 MWh/year, respectively. Moreover, shape and scale parameters for each wind directions and annual energy generation values of each location have been calculated within the scope of this work.
- Open Access
- 29 December 2022
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 7 (2) , 99-111
Software-based solar energy potential assessment for an industrial facility: a case study from Aegean Region of Turkey
Solar energy is considered as one of the clean and sustainable energy sources. As known, big portion of the energy demand in industrial processes are generally met by fossil energy sources. Utilizing renewable and sustainable energy technologies in industrial facilities can decrease negative environmental effects. In this study, applicability of a rooftop solar energy generation system in an industrial building has been analyzed. In the simulation process, PvSOL software has been employed. Considering available areas on the roof of the facility, solar electrical energy generation system with installed power of 573.75 kWp was planned and simulated. Moreover, economic analysis results of the proposed rooftop solar energy system were presented within the scope of this research. According to the economic analysis outcomes, payback period of the proposed rooftop energy system was achieved less than 4 years.
- 29 December 2022
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 7 (2) , 99-111
Open AccessSoftware-based solar energy potential assessment for an industrial facility: a case study from Aegean Region of Turkey
Solar energy is considered as one of the clean and sustainable energy sources. As known, big portion of the energy demand in industrial processes are generally met by fossil energy sources. Utilizing renewable and sustainable energy technologies in industrial facilities can decrease negative environmental effects. In this study, applicability of a rooftop solar energy generation system in an industrial building has been analyzed. In the simulation process, PvSOL software has been employed. Considering available areas on the roof of the facility, solar electrical energy generation system with installed power of 573.75 kWp was planned and simulated. Moreover, economic analysis results of the proposed rooftop solar energy system were presented within the scope of this research. According to the economic analysis outcomes, payback period of the proposed rooftop energy system was achieved less than 4 years.