Balaraman Panneerselvam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Balaraman Panneerselvam has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Veloorillom Madhavan Sreehari
School of Mechanical Engineering, SASTRA Deemed University, Thanjavur, India
2 shared publications - Kathhi Palaksha Reddy
School of Mechanical Engineering, SASTRA Deemed University, Thanjavur, India
1 shared publication - Thanjavur Krishnammorthy Kandavel
School of Mechanical Engineering, SASTRA Deemed University, Thanjavur, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by University Library in Kragujevac in Tribology and Materials
- Vol. 3 (3) , 141-149
Investigations on dry sliding wear and friction behaviour of alloy steel obtained by powder metallurgy
The present work investigates the dry sliding wear and friction behaviour of an alloy steel developed through powder metallurgy. Prealloyed Atomet 4601 powder was thoroughly mixed with elemental powders of 0.35 C, 0.25 Mn, 0.1 Si and 0.9 Cr (in wt. %) to create this alloy steel, whose composition closely matches EN24 (AISI 4340) wrought steel. The dry sliding friction and wear test experiments were performed in a pin-on-disc tribometer. For the various cases considered in friction and wear tests, the wear rate is lowest (0.32 × 10–3 mm3/m) at 15 N and 1.77 m/s and highest (1.02 × 10–3 mm3/m) under severe conditions of 32.5 N and 2.83 m/s. The coefficient of friction is highest (0.673) at 15 N and 0.71 m/s and lowest (0.1311) at 32.5 N and 2.83 m/s. Subsequently, regression models are developed based on experimental results and the interaction effect of load and speed on the response parameters are plotted using MATLAB. An R2 value of 0.98 indicates a strong correlation between the response and the input variables. X-ray diffraction (XRD) and optical and scanning electron microscope (SEM) analyses of the most worn specimens revealed carbides and oxides in the ferrite grain matrix, with adhesive, abrasive and oxidative wear being the primary mechanisms observed.
- 1 January 2024
- Published by University Library in Kragujevac in Tribology and Materials
- Vol. 3 (3) , 141-149
Open AccessInvestigations on dry sliding wear and friction behaviour of alloy steel obtained by powder metallurgy
The present work investigates the dry sliding wear and friction behaviour of an alloy steel developed through powder metallurgy. Prealloyed Atomet 4601 powder was thoroughly mixed with elemental powders of 0.35 C, 0.25 Mn, 0.1 Si and 0.9 Cr (in wt. %) to create this alloy steel, whose composition closely matches EN24 (AISI 4340) wrought steel. The dry sliding friction and wear test experiments were performed in a pin-on-disc tribometer. For the various cases considered in friction and wear tests, the wear rate is lowest (0.32 × 10–3 mm3/m) at 15 N and 1.77 m/s and highest (1.02 × 10–3 mm3/m) under severe conditions of 32.5 N and 2.83 m/s. The coefficient of friction is highest (0.673) at 15 N and 0.71 m/s and lowest (0.1311) at 32.5 N and 2.83 m/s. Subsequently, regression models are developed based on experimental results and the interaction effect of load and speed on the response parameters are plotted using MATLAB. An R2 value of 0.98 indicates a strong correlation between the response and the input variables. X-ray diffraction (XRD) and optical and scanning electron microscope (SEM) analyses of the most worn specimens revealed carbides and oxides in the ferrite grain matrix, with adhesive, abrasive and oxidative wear being the primary mechanisms observed.
- Open Access
- 19 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 455 (1) , 012128
A comprehensive study on the buckling of sandwich plates
Advancements in aeromechanical materials is a significant topic of research in recent days. Better understanding of structural behaviour is vital for the manufacturing of aircraft and spacecraft components. Sandwich plates can be employed for several applications, especially for making airplane and rocket structures. These all motivate researchers to investigate on the modelling and analysis of advanced materials like carbon nanotubes, laminated composites, functionally graded materials, sandwich structures, etc. Sandwich plates have thin outer facings containing a core in between. The objective of the present work is to conduct a detailed study of the buckling response of sandwich plates employing first order and higher order shear deformation theories considering various aspects. Numerical formulation has been carried out initially. Programing in Matlab environment has been done. Detailed parametric studies also conducted to provide clear understanding of the behaviour of buckling of sandwich structures.
- 19 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 455 (1) , 012128
Open AccessA comprehensive study on the buckling of sandwich plates
Advancements in aeromechanical materials is a significant topic of research in recent days. Better understanding of structural behaviour is vital for the manufacturing of aircraft and spacecraft components. Sandwich plates can be employed for several applications, especially for making airplane and rocket structures. These all motivate researchers to investigate on the modelling and analysis of advanced materials like carbon nanotubes, laminated composites, functionally graded materials, sandwich structures, etc. Sandwich plates have thin outer facings containing a core in between. The objective of the present work is to conduct a detailed study of the buckling response of sandwich plates employing first order and higher order shear deformation theories considering various aspects. Numerical formulation has been carried out initially. Programing in Matlab environment has been done. Detailed parametric studies also conducted to provide clear understanding of the behaviour of buckling of sandwich structures.