Ilgiz Galiev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ilgiz Galiev has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Bulat Ziganshin
Kazan State Agrarian University
5 shared publications - Fanil' Gabdrafikov
FGBOU VO «Bashkirskiy gosudarstvennyy agrarnyy universitet
5 shared publications Kamil Khafizov
Kazan State Agrarian University
4 shared publications- Rail Khusainov
Kazan State Agrarian University
4 shared publications Al'BErt Muhametshin
FGBOU VO «Kazanskiy gosudarstvennyy agrarnyy universitet
3 shared publicationsNail Adigamov
Kazan State Agrarian University
3 shared publications
Latest Publications
- 15 November 2026
- Published by ECO-Vector LLC (Publications) in Tractors and Agricultural Machinery
Ensuring the Performance of a Turbocharger Bearing Assembly of an Internal Combustion Engine
BACKGROUND: To increase power, modern internal combustion engines are equipped with turbochargers operating at high speeds and temperatures. The most heavily loaded component of a turbocharger is the bearing assembly. Its performance is largely determined by the lubrication system. When the engine lubrication systems and turbocharger bearings operate together, small abrasive particles generated by wear on the engine's friction components enter the bearing assembly along with the lubricant. This leads to increased wear and a reduced remaining service life of the bearing and the entire assembly. Therefore, a scientific hypothesis has been put forward that using a separate lubrication system for the turbocharger bearing assembly will increase engine life. AIM: To compare the change in the condition of turbochargers using a standard lubrication system and using a lubrication system for individual bearing assemblies. METHODS: A design for an individual lubrication system for the TKR-11 turbocharger bearing assembly for the YaMZ 238 engine has been developed, the novelty of which is confirmed by a patent. The effectiveness of the individual lubrication system was assessed through the effect of the bearing's remaining life on the mean time between failures of the entire turbocharger, depending on the vehicle's mileage. For this purpose, experimental studies were conducted under real-life operating conditions using KAMAZ vehicles equipped with a TRK-11 turbocharger. The experiment involved 13 vehicles with a standard (combined) lubrication system and three vehicles with an individual bearing assembly lubrication system. Vehicle mileage and changes in the turbocharger bearing assembly clearance were recorded during maintenance. RESULTS: With standard lubrication, the rotor spin-up time was 50 seconds, and by the sixth second, the pressure in the central oil line and in front of the rotor bearing had dropped to zero, indicating a semi-fluid or dry friction mode. With a dedicated lubrication system, the rotor rotated for up to 90 seconds. During this time, the oil pressure was 0.03 MPa. With standard turbocharger bearing lubrication, its service life is exhausted after 160,000 km. With a dedicated lubrication system, only 40% of the turbocharger bearing's service life is consumed over the same period. CONCLUSION: The dependence of the change in the remaining service life of a turbocharger bearing on the vehicle mileage was obtained. With a vehicle mileage of 70,000 km, the remaining service life of a bearing assembly with an individual lubrication system is twice that of one with standard lubrication; for vehicles with a mileage of 100,000 km, the increase was 42%; for vehicles with a mileage of 130,000 km, it was 34%.
- 15 November 2026
- Published by ECO-Vector LLC (Publications) in Tractors and Agricultural Machinery
Ensuring the Performance of a Turbocharger Bearing Assembly of an Internal Combustion Engine
BACKGROUND: To increase power, modern internal combustion engines are equipped with turbochargers operating at high speeds and temperatures. The most heavily loaded component of a turbocharger is the bearing assembly. Its performance is largely determined by the lubrication system. When the engine lubrication systems and turbocharger bearings operate together, small abrasive particles generated by wear on the engine's friction components enter the bearing assembly along with the lubricant. This leads to increased wear and a reduced remaining service life of the bearing and the entire assembly. Therefore, a scientific hypothesis has been put forward that using a separate lubrication system for the turbocharger bearing assembly will increase engine life. AIM: To compare the change in the condition of turbochargers using a standard lubrication system and using a lubrication system for individual bearing assemblies. METHODS: A design for an individual lubrication system for the TKR-11 turbocharger bearing assembly for the YaMZ 238 engine has been developed, the novelty of which is confirmed by a patent. The effectiveness of the individual lubrication system was assessed through the effect of the bearing's remaining life on the mean time between failures of the entire turbocharger, depending on the vehicle's mileage. For this purpose, experimental studies were conducted under real-life operating conditions using KAMAZ vehicles equipped with a TRK-11 turbocharger. The experiment involved 13 vehicles with a standard (combined) lubrication system and three vehicles with an individual bearing assembly lubrication system. Vehicle mileage and changes in the turbocharger bearing assembly clearance were recorded during maintenance. RESULTS: With standard lubrication, the rotor spin-up time was 50 seconds, and by the sixth second, the pressure in the central oil line and in front of the rotor bearing had dropped to zero, indicating a semi-fluid or dry friction mode. With a dedicated lubrication system, the rotor rotated for up to 90 seconds. During this time, the oil pressure was 0.03 MPa. With standard turbocharger bearing lubrication, its service life is exhausted after 160,000 km. With a dedicated lubrication system, only 40% of the turbocharger bearing's service life is consumed over the same period. CONCLUSION: The dependence of the change in the remaining service life of a turbocharger bearing on the vehicle mileage was obtained. With a vehicle mileage of 70,000 km, the remaining service life of a bearing assembly with an individual lubrication system is twice that of one with standard lubrication; for vehicles with a mileage of 100,000 km, the increase was 42%; for vehicles with a mileage of 130,000 km, it was 34%.
- Open Access
- 1 November 2024
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 19 (3) , 52-58
INVESTIGATION OF THE EFFECT OF ELECTROZONING ON THE SHELF LIFE OF RIPE STRAWBERRIES
Preserving the freshness of fruits and berries is of great importance not only for their taste, but also for preserving their nutritional properties. Ozonation is one of the highly effective methods for destroying bacterial microflora and preserving food for a long time. Ozone is a strong disinfecting gas with a powerful disinfecting effect; biochemical processes are greatly reduced in ozonated products. Studies to study the effect of ozonation on the preservation of freshness and appearance of berries were conducted on the example of strawberries of the "Black Prince" variety. Experiments on electrozoning of ripe strawberries were carried out in laboratory conditions in the Chuvash State Agrarian University. For this purpose, an experimental installation was developed and implemented to study the effects of ozonation. In a series of one-factor experiments, the preservation, appearance of berries and the amount of microflora after 6 days of storage were determined. Ozonation of berries was carried out in special containers at an ozone concentration of 6 mg / m3, lasting 2 hours - 2 times a day. The appearance and taste of strawberries treated with ozonation for six days has not changed; the number of microorganisms on the surface of berries during storage for up to six days corresponds to the standards of GOST 29187-91. A visual inspection of the berries in the control sample on the sixth day of storage showed that 90% of the berries were affected by mold fungi. Unprocessed berries lost their shape, softened, putrefactive microflora appeared; the surface area affected by mold fungi reached more than 90%. Thus, ozonation has shown high efficiency in preserving the freshness, appearance and quality of strawberries during storage. Ozone treatment significantly reduces the development of pathogenic microflora and prevents spoilage of berries. This method can be recommended to extend the shelf life of fruits and berries in the food industry.
- 1 November 2024
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 19 (3) , 52-58
Open AccessINVESTIGATION OF THE EFFECT OF ELECTROZONING ON THE SHELF LIFE OF RIPE STRAWBERRIES
Preserving the freshness of fruits and berries is of great importance not only for their taste, but also for preserving their nutritional properties. Ozonation is one of the highly effective methods for destroying bacterial microflora and preserving food for a long time. Ozone is a strong disinfecting gas with a powerful disinfecting effect; biochemical processes are greatly reduced in ozonated products. Studies to study the effect of ozonation on the preservation of freshness and appearance of berries were conducted on the example of strawberries of the "Black Prince" variety. Experiments on electrozoning of ripe strawberries were carried out in laboratory conditions in the Chuvash State Agrarian University. For this purpose, an experimental installation was developed and implemented to study the effects of ozonation. In a series of one-factor experiments, the preservation, appearance of berries and the amount of microflora after 6 days of storage were determined. Ozonation of berries was carried out in special containers at an ozone concentration of 6 mg / m3, lasting 2 hours - 2 times a day. The appearance and taste of strawberries treated with ozonation for six days has not changed; the number of microorganisms on the surface of berries during storage for up to six days corresponds to the standards of GOST 29187-91. A visual inspection of the berries in the control sample on the sixth day of storage showed that 90% of the berries were affected by mold fungi. Unprocessed berries lost their shape, softened, putrefactive microflora appeared; the surface area affected by mold fungi reached more than 90%. Thus, ozonation has shown high efficiency in preserving the freshness, appearance and quality of strawberries during storage. Ozone treatment significantly reduces the development of pathogenic microflora and prevents spoilage of berries. This method can be recommended to extend the shelf life of fruits and berries in the food industry.
- Open Access
- 13 August 2024
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 19 (2) , 44-50
A GENERAL APPROACH TO SOLVING THE PROBLEM OF ENSURING THE EFFICIENCY OF TRACTORS IN THE AGRO-INDUSTRIAL INDUSTRY
Agricultural production is characterized by the seasonality of mechanized work in the cultivation of crops. In addition, the amount of wear on aggregates and equipment systems is determined, on the one hand, by natural and climatic conditions and, on the other, by the nomenclature of operations performed in the planned period, organizational, production and technical conditions in a particular farm. Tractor units and systems are interconnect with each other and interdependent on each other, i.e. the amount of wear of some parts affects the wear of others. In this regard, the purpose of the research is to develop a concept for ensuring the operability of tractors in the agro-industrial complex by optimizing the resource consumption of aggregates and systems, taking into account the conditions of their operation. The most promising direction for improving the efficiency of tractor operation is the development of measures to optimize the resource consumption of their units and systems, taking into account the operating conditions of machinery in the agro-industrial complex. To predict changes in the physical parameter of a part, unit, and tractor system for the planned period of a certain amount of work, a concept is introduced - an indicator of resource consumption, which determines the amount of change in the diagnostic parameter of the unit state per unit of work performed. The assessment of the tractor condition is carry out by the level of equipment resource consumption, which makes it possible to promptly respond to the state of technical operation of equipment, the conditions of their operation and develop measures to optimize resource consumption. The resource consumption level (Urr) of the tractor, theoretically, can vary from 0 to 1. In this case, Urr=0 it is assumed that the tractor is written off from the balance sheet of the farm or is missing; with Urr=1, it is assumed that the tractor is in good condition and all tractor parameters have nominal values. With known patterns of changes in the level of resource consumption for various types of agricultural operations, it becomes possible to plan the range of work for each tractor for the planned period, taking into account the optimal resource consumption of their units and systems.
- 13 August 2024
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 19 (2) , 44-50
Open AccessA GENERAL APPROACH TO SOLVING THE PROBLEM OF ENSURING THE EFFICIENCY OF TRACTORS IN THE AGRO-INDUSTRIAL INDUSTRY
Agricultural production is characterized by the seasonality of mechanized work in the cultivation of crops. In addition, the amount of wear on aggregates and equipment systems is determined, on the one hand, by natural and climatic conditions and, on the other, by the nomenclature of operations performed in the planned period, organizational, production and technical conditions in a particular farm. Tractor units and systems are interconnect with each other and interdependent on each other, i.e. the amount of wear of some parts affects the wear of others. In this regard, the purpose of the research is to develop a concept for ensuring the operability of tractors in the agro-industrial complex by optimizing the resource consumption of aggregates and systems, taking into account the conditions of their operation. The most promising direction for improving the efficiency of tractor operation is the development of measures to optimize the resource consumption of their units and systems, taking into account the operating conditions of machinery in the agro-industrial complex. To predict changes in the physical parameter of a part, unit, and tractor system for the planned period of a certain amount of work, a concept is introduced - an indicator of resource consumption, which determines the amount of change in the diagnostic parameter of the unit state per unit of work performed. The assessment of the tractor condition is carry out by the level of equipment resource consumption, which makes it possible to promptly respond to the state of technical operation of equipment, the conditions of their operation and develop measures to optimize resource consumption. The resource consumption level (Urr) of the tractor, theoretically, can vary from 0 to 1. In this case, Urr=0 it is assumed that the tractor is written off from the balance sheet of the farm or is missing; with Urr=1, it is assumed that the tractor is in good condition and all tractor parameters have nominal values. With known patterns of changes in the level of resource consumption for various types of agricultural operations, it becomes possible to plan the range of work for each tractor for the planned period, taking into account the optimal resource consumption of their units and systems.
- Open Access
- 2 October 2023
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 18 (3) , 68-75
PROCESSING THE RESULTS OF EXPERIMENTAL STUDIES OF THE USE OF TECHNOLOGIES OF INTEGRATED MICROPLASMA HARDENING OF WORKING UNITS AND PARTS OF AGRICULTURAL MACHINES
Today, the problem of maintaining the efficiency of complex modern domestic and foreign agricultural machines is quite acute. The working units of agricultural tillage machines operate in an aggressive abrasive environment, which leads to their intensive wear and, as a result, to the loss of geometric shape. This, in turn, leads to a violation of agrotechnical requirements, which significantly affects the yield of cultivated crops. Serial working units of soil-cultivating machines are made of alloy steels of the ST65G type with a working hardness of HRC 55 ... 60. The purpose of the research is to increase the wear resistance of the working bodies of tillage agricultural machines by using the technology of complex microplasma hardening, with the development of a methodology for determining rational modes of processing working surfaces. To evaluate the effectiveness of complex hardening of laboratory samples, studies of the elemental composition of the hardened layer were carried out. Plates made of ST65G steel were used as laboratory samples. Hardening was carried out using various combinations of cermet powders and microplasma hardening modes. Determination of wear resistance was carried out on a friction machine 77 MT-1. The best results were noted after vibro-arc hardening followed by electrospark alloying and the use of a cermet powder consisting of 80% PG-10N-01 matrix powder and 20% B4C boron carbide. Based on the indicators of hardening regimes, Lagrange interpolation polynomials were constructed, which describe the dependence of the amount of sample wear on the current and voltage, an algorithm was developed for determining rational hardening regimes to achieve maximum wear resistance of the studied samples. The microhardness of the surface of products during electrospark hardening increased up to 2 times, and with vibroarc in combination with electrospark alloying and the use of special pastes with cermet powders - more than 3 times. The depth of the hardened surface layer with complex hardening is about 0.3 mm.
- 2 October 2023
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 18 (3) , 68-75
Open AccessPROCESSING THE RESULTS OF EXPERIMENTAL STUDIES OF THE USE OF TECHNOLOGIES OF INTEGRATED MICROPLASMA HARDENING OF WORKING UNITS AND PARTS OF AGRICULTURAL MACHINES
Today, the problem of maintaining the efficiency of complex modern domestic and foreign agricultural machines is quite acute. The working units of agricultural tillage machines operate in an aggressive abrasive environment, which leads to their intensive wear and, as a result, to the loss of geometric shape. This, in turn, leads to a violation of agrotechnical requirements, which significantly affects the yield of cultivated crops. Serial working units of soil-cultivating machines are made of alloy steels of the ST65G type with a working hardness of HRC 55 ... 60. The purpose of the research is to increase the wear resistance of the working bodies of tillage agricultural machines by using the technology of complex microplasma hardening, with the development of a methodology for determining rational modes of processing working surfaces. To evaluate the effectiveness of complex hardening of laboratory samples, studies of the elemental composition of the hardened layer were carried out. Plates made of ST65G steel were used as laboratory samples. Hardening was carried out using various combinations of cermet powders and microplasma hardening modes. Determination of wear resistance was carried out on a friction machine 77 MT-1. The best results were noted after vibro-arc hardening followed by electrospark alloying and the use of a cermet powder consisting of 80% PG-10N-01 matrix powder and 20% B4C boron carbide. Based on the indicators of hardening regimes, Lagrange interpolation polynomials were constructed, which describe the dependence of the amount of sample wear on the current and voltage, an algorithm was developed for determining rational hardening regimes to achieve maximum wear resistance of the studied samples. The microhardness of the surface of products during electrospark hardening increased up to 2 times, and with vibroarc in combination with electrospark alloying and the use of special pastes with cermet powders - more than 3 times. The depth of the hardened surface layer with complex hardening is about 0.3 mm.
- Open Access
- 21 September 2022
- Published by EDP Sciences in BIO Web of Conferences
- Vol. 52, 00028
Modernization of the fuel supply system in the internal combustion engine by electronic control of the ring valve
The research was carried out in order to develop a method for skipping fuel supplies (turning off individual piston strokes) at low frequencies of crankshaft rotations and at partial engine operating modes with direct-acting fuel supply systems to increase fuel efficiency. The developed method is easily implement using a ring-type discharge valve with electronic control. A valve made in the form of a split elastic ring and installed in a high-pressure line above the plunger pair controls the fuel supply. An electromagnet, located in the cavity of the annular valve, controls the valve, using an electronic regulator, acting at the right moment according to the signals coming from the sensors of the engine crankshaft speed, the volume of incoming air and the position of the piston. The proposed direct-acting fuel supply system with an electronically controlled ring valve reliably ensures the speed and load characteristics of the engine by affecting the number of cyclic feeds. With a decrease in the load and speed of the engine crankshaft, the number of cyclic fuel supplies decreases due to a decrease in signals sent to the electromagnet winding and, as a result, the valve does not attract the fuel and misses the fuel supply. Reducing the unevenness of the fuel supply by the dynamic component that occurs when the supply is switch off is ensured by reducing the inertia of the regulator due to the electronic control of the ring valve. The developed mathematical model of a direct-acting fuel supply system with an annular discharge valve allows us to reveal the relationship of fuel supply parameters with the design dimensions of the split ring. Such direct-acting fuel supply system with an electronically controlled discharge valve allows, due to the skipping of working strokes in low-load and idle modes, redistributing the provided amount of fuel to the working cylinders, significantly reducing fuel consumption.
- 21 September 2022
- Published by EDP Sciences in BIO Web of Conferences
- Vol. 52, 00028
Open AccessModernization of the fuel supply system in the internal combustion engine by electronic control of the ring valve
The research was carried out in order to develop a method for skipping fuel supplies (turning off individual piston strokes) at low frequencies of crankshaft rotations and at partial engine operating modes with direct-acting fuel supply systems to increase fuel efficiency. The developed method is easily implement using a ring-type discharge valve with electronic control. A valve made in the form of a split elastic ring and installed in a high-pressure line above the plunger pair controls the fuel supply. An electromagnet, located in the cavity of the annular valve, controls the valve, using an electronic regulator, acting at the right moment according to the signals coming from the sensors of the engine crankshaft speed, the volume of incoming air and the position of the piston. The proposed direct-acting fuel supply system with an electronically controlled ring valve reliably ensures the speed and load characteristics of the engine by affecting the number of cyclic feeds. With a decrease in the load and speed of the engine crankshaft, the number of cyclic fuel supplies decreases due to a decrease in signals sent to the electromagnet winding and, as a result, the valve does not attract the fuel and misses the fuel supply. Reducing the unevenness of the fuel supply by the dynamic component that occurs when the supply is switch off is ensured by reducing the inertia of the regulator due to the electronic control of the ring valve. The developed mathematical model of a direct-acting fuel supply system with an annular discharge valve allows us to reveal the relationship of fuel supply parameters with the design dimensions of the split ring. Such direct-acting fuel supply system with an electronically controlled discharge valve allows, due to the skipping of working strokes in low-load and idle modes, redistributing the provided amount of fuel to the working cylinders, significantly reducing fuel consumption.
- 23 April 2022
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 17 (1) , 67-72
SUBSTANTIATION OF THE PARAMETERS OF VACUUM PUMPING FACILITIES WITH A PULSING ACTIVE FLOW
Vacuum pumping devices designed for dosing, mixing, transporting and distributing feed; milking cows; milk processing and other technological processes in agriculture are among the main components of the technological processes of animal husbandry. In order to improve the technical characteristics of vacuum pumping devices, widely used in all industries, it is proposed to use a pulsating jet apparatus installed on the suction port of a liquid ring vacuum pump. To characterize a stationary flow, the reduced velocity and the Reynolds number are usually used, and in the case of a pulsating flow, the relative frequency and relative amplitude of the pulsations are added to them, which are necessary to determine the design and technological parameters. One of the main design parameters of the operation of a jet vacuum pumping device is the ejection coefficient, the increase of which is achieved by deliberately violating the stationary mode of material flow by adding a pulsating device. The object of experimental research was a jet apparatus with a pulsating active flow. As an interrupting mechanism for an ejector with a pulsating active flow, it is advisable to use a ball-shaped valve made of various materials, which, due to the pressure drop and a return spring, can pulsate at a frequency of 90 ... 100 beats/min. During the experiments, the change in the supply of a water-ring vacuum pump with a pulsating jet apparatus was determined depending on the materials of the ball-type valve (steel, rubber and textolite), the suction pressure (1; 5; 10; 20; 30; 40; 50; 60 kPa), valve pulsation frequency (85; 100; 115; 130 beats/min) and ejector inlet pressure (20; 30; 50; 60 kPa). The best result is noted when using a valve in the form of a ball made of steel. In this variant, the supply of a water ring vacuum pump with a pulsating jet apparatus is increased to 14.5 m3/min, and the maximum supply is provided at a pulsation frequency of 90...100 beats/min
- 23 April 2022
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 17 (1) , 67-72
SUBSTANTIATION OF THE PARAMETERS OF VACUUM PUMPING FACILITIES WITH A PULSING ACTIVE FLOW
Vacuum pumping devices designed for dosing, mixing, transporting and distributing feed; milking cows; milk processing and other technological processes in agriculture are among the main components of the technological processes of animal husbandry. In order to improve the technical characteristics of vacuum pumping devices, widely used in all industries, it is proposed to use a pulsating jet apparatus installed on the suction port of a liquid ring vacuum pump. To characterize a stationary flow, the reduced velocity and the Reynolds number are usually used, and in the case of a pulsating flow, the relative frequency and relative amplitude of the pulsations are added to them, which are necessary to determine the design and technological parameters. One of the main design parameters of the operation of a jet vacuum pumping device is the ejection coefficient, the increase of which is achieved by deliberately violating the stationary mode of material flow by adding a pulsating device. The object of experimental research was a jet apparatus with a pulsating active flow. As an interrupting mechanism for an ejector with a pulsating active flow, it is advisable to use a ball-shaped valve made of various materials, which, due to the pressure drop and a return spring, can pulsate at a frequency of 90 ... 100 beats/min. During the experiments, the change in the supply of a water-ring vacuum pump with a pulsating jet apparatus was determined depending on the materials of the ball-type valve (steel, rubber and textolite), the suction pressure (1; 5; 10; 20; 30; 40; 50; 60 kPa), valve pulsation frequency (85; 100; 115; 130 beats/min) and ejector inlet pressure (20; 30; 50; 60 kPa). The best result is noted when using a valve in the form of a ball made of steel. In this variant, the supply of a water ring vacuum pump with a pulsating jet apparatus is increased to 14.5 m3/min, and the maximum supply is provided at a pulsation frequency of 90...100 beats/min
- 23 April 2022
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 17 (1) , 38-44
DIRECT FUEL SUPPLY SYSTEM WITH ELECTRONICALLY CONTROLLED RING VALVE
The studies were carried out with the aim of developing a method for skipping fuel supplies (turning off individual working piston strokes) at low crankshaft rotational speeds and at partial engine operating modes at low load in direct-acting fuel supply systems to improve fuel efficiency. The developed method is easily implemented using an electronically controlled ring-type discharge valve. A valve made in the form of rigid elastic ring and installed in the high-pressure line above the plunger pair regulates fuel skip. An electromagnet located in the cavity of the annular valve controls it using an electronic regulator, acting at the right time according to the signals coming from the sensors of the engine crankshaft speed, the volume of incoming air and the position of the piston. The proposed fuel supply system of direct action with an electronically controlled annular valve reliably ensures the speed and load characteristics of the engine by influencing the number of cycle fuel supplies. With a decrease in the load and speed of the engine crankshaft, the number of fuel supply cycle’s decreases due to a decrease in signals to the electromagnet winding and, as a result, the valve is not attracted and the fuel supply is skipped. A decrease in the unevenness of the fuel supply in terms of the dynamic component that occurs when the supply is turned off is ensured by a decrease in the inertia of the regulator action due to the electronic control of the annular valve. The developed mathematical model of a direct-acting fuel supply system with an annular pressure valve makes it possible to reveal the relationship between the fuel supply parameters and the design dimensions of the split ring. Such a fuel supply system of direct action with an electronically controlled delivery valve allows, due to skipping of working strokes in low load and idle modes, redistributing the provided volume of fuel to working cylinders, significantly reduce fuel consumption
- 23 April 2022
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 17 (1) , 38-44
DIRECT FUEL SUPPLY SYSTEM WITH ELECTRONICALLY CONTROLLED RING VALVE
The studies were carried out with the aim of developing a method for skipping fuel supplies (turning off individual working piston strokes) at low crankshaft rotational speeds and at partial engine operating modes at low load in direct-acting fuel supply systems to improve fuel efficiency. The developed method is easily implemented using an electronically controlled ring-type discharge valve. A valve made in the form of rigid elastic ring and installed in the high-pressure line above the plunger pair regulates fuel skip. An electromagnet located in the cavity of the annular valve controls it using an electronic regulator, acting at the right time according to the signals coming from the sensors of the engine crankshaft speed, the volume of incoming air and the position of the piston. The proposed fuel supply system of direct action with an electronically controlled annular valve reliably ensures the speed and load characteristics of the engine by influencing the number of cycle fuel supplies. With a decrease in the load and speed of the engine crankshaft, the number of fuel supply cycle’s decreases due to a decrease in signals to the electromagnet winding and, as a result, the valve is not attracted and the fuel supply is skipped. A decrease in the unevenness of the fuel supply in terms of the dynamic component that occurs when the supply is turned off is ensured by a decrease in the inertia of the regulator action due to the electronic control of the annular valve. The developed mathematical model of a direct-acting fuel supply system with an annular pressure valve makes it possible to reveal the relationship between the fuel supply parameters and the design dimensions of the split ring. Such a fuel supply system of direct action with an electronically controlled delivery valve allows, due to skipping of working strokes in low load and idle modes, redistributing the provided volume of fuel to working cylinders, significantly reduce fuel consumption
- 20 April 2022
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 17 (1) , 38-44
DIRECT FUEL SUPPLY SYSTEM WITH ELECTRONICALLY CONTROLLED RING VALVE
The studies were carried out with the aim of developing a method for skipping fuel supplies (turning off individual working piston strokes) at low crankshaft rotational speeds and at partial engine operating modes at low load in direct-acting fuel supply systems to improve fuel efficiency. The developed method is easily implemented using an electronically controlled ring-type discharge valve. A valve made in the form of rigid elastic ring and installed in the high-pressure line above the plunger pair regulates fuel skip. An electromagnet located in the cavity of the annular valve controls it using an electronic regulator, acting at the right time according to the signals coming from the sensors of the engine crankshaft speed, the volume of incoming air and the position of the piston. The proposed fuel supply system of direct action with an electronically controlled annular valve reliably ensures the speed and load characteristics of the engine by influencing the number of cycle fuel supplies. With a decrease in the load and speed of the engine crankshaft, the number of fuel supply cycle’s decreases due to a decrease in signals to the electromagnet winding and, as a result, the valve is not attracted and the fuel supply is skipped. A decrease in the unevenness of the fuel supply in terms of the dynamic component that occurs when the supply is turned off is ensured by a decrease in the inertia of the regulator action due to the electronic control of the annular valve. The developed mathematical model of a direct-acting fuel supply system with an annular pressure valve makes it possible to reveal the relationship between the fuel supply parameters and the design dimensions of the split ring. Such a fuel supply system of direct action with an electronically controlled delivery valve allows, due to skipping of working strokes in low load and idle modes, redistributing the provided volume of fuel to working cylinders, significantly reduce fuel consumption
- 20 April 2022
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 17 (1) , 38-44
DIRECT FUEL SUPPLY SYSTEM WITH ELECTRONICALLY CONTROLLED RING VALVE
The studies were carried out with the aim of developing a method for skipping fuel supplies (turning off individual working piston strokes) at low crankshaft rotational speeds and at partial engine operating modes at low load in direct-acting fuel supply systems to improve fuel efficiency. The developed method is easily implemented using an electronically controlled ring-type discharge valve. A valve made in the form of rigid elastic ring and installed in the high-pressure line above the plunger pair regulates fuel skip. An electromagnet located in the cavity of the annular valve controls it using an electronic regulator, acting at the right time according to the signals coming from the sensors of the engine crankshaft speed, the volume of incoming air and the position of the piston. The proposed fuel supply system of direct action with an electronically controlled annular valve reliably ensures the speed and load characteristics of the engine by influencing the number of cycle fuel supplies. With a decrease in the load and speed of the engine crankshaft, the number of fuel supply cycle’s decreases due to a decrease in signals to the electromagnet winding and, as a result, the valve is not attracted and the fuel supply is skipped. A decrease in the unevenness of the fuel supply in terms of the dynamic component that occurs when the supply is turned off is ensured by a decrease in the inertia of the regulator action due to the electronic control of the annular valve. The developed mathematical model of a direct-acting fuel supply system with an annular pressure valve makes it possible to reveal the relationship between the fuel supply parameters and the design dimensions of the split ring. Such a fuel supply system of direct action with an electronically controlled delivery valve allows, due to skipping of working strokes in low load and idle modes, redistributing the provided volume of fuel to working cylinders, significantly reduce fuel consumption
- 21 November 2021
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 16 (3) , 67-71
MODERNIZATION OF THE LUBRICATION SYSTEM OF THE TURBOCHARGER BEARING OF THE DIESEL ENGINE
The problem of increasing the unit power of the engine without making changes to its design is solve by using a turbo supercharger. However, due to the intensity of the turbochargers operating mode, which are characterized by engine speed variability due to changing load indicators during operation (the number of rotor revolutions varies from 30000 min-1 to 120000 min-1, engine exhaust gases have a temperature of about 7500C), there is a need to improve the efficiency of the turbocharger bearing lubrication system. The purpose of the research is to ensure the operability and increase the reliability of turbochargers of diesel engines. To achieve this goal, a constructive solution for the lubrication system of the bearing assembly was propose, i.e., a membrane-type hydraulic accumulator was structurally provided in the lubrication system of the bearing assembly. Experimental studies were conduct to identify the operability and effectiveness of this constructive solution. The experiment was carried out on the KAMAZ-740 engine, the turbocharger shaft drive was carried out in normal mode, that is, from exhaust gases. L-02-40 fuel was use, SAE 10W–40 API was use as a lubricant. The turbocharger shaft speed varied from minimum to maximum by changing the engine speed and then stopping it. During the experiments, the following parameters of the turbocharger operation were measure: the duration of inertial rotation of the turbocharger rotor; the duration of pressure reduction in the turbocharger lubrication system. The dependences of the influence of the duration of the pressure drop in the turbocharger lubrication system and the duration of rotation of the turbocharger shaft by inertia with parallel inclusion of the accumulator in its lubrication system and in the normal mode of lubrication of the bearing are reveal. It is established that the installation of a device for feeding the turbocharger bearing during a sharp reduction in engine speed will increase the run-out of the turbocharger rotor from 30 to 65 s while maintaining the normal operating mode of the turbocharger lubrication system
- 21 November 2021
- Published by Kazan State Agrarian University in Vestnik of Kazan State Agrarian University
- Vol. 16 (3) , 67-71
MODERNIZATION OF THE LUBRICATION SYSTEM OF THE TURBOCHARGER BEARING OF THE DIESEL ENGINE
The problem of increasing the unit power of the engine without making changes to its design is solve by using a turbo supercharger. However, due to the intensity of the turbochargers operating mode, which are characterized by engine speed variability due to changing load indicators during operation (the number of rotor revolutions varies from 30000 min-1 to 120000 min-1, engine exhaust gases have a temperature of about 7500C), there is a need to improve the efficiency of the turbocharger bearing lubrication system. The purpose of the research is to ensure the operability and increase the reliability of turbochargers of diesel engines. To achieve this goal, a constructive solution for the lubrication system of the bearing assembly was propose, i.e., a membrane-type hydraulic accumulator was structurally provided in the lubrication system of the bearing assembly. Experimental studies were conduct to identify the operability and effectiveness of this constructive solution. The experiment was carried out on the KAMAZ-740 engine, the turbocharger shaft drive was carried out in normal mode, that is, from exhaust gases. L-02-40 fuel was use, SAE 10W–40 API was use as a lubricant. The turbocharger shaft speed varied from minimum to maximum by changing the engine speed and then stopping it. During the experiments, the following parameters of the turbocharger operation were measure: the duration of inertial rotation of the turbocharger rotor; the duration of pressure reduction in the turbocharger lubrication system. The dependences of the influence of the duration of the pressure drop in the turbocharger lubrication system and the duration of rotation of the turbocharger shaft by inertia with parallel inclusion of the accumulator in its lubrication system and in the normal mode of lubrication of the bearing are reveal. It is established that the installation of a device for feeding the turbocharger bearing during a sharp reduction in engine speed will increase the run-out of the turbocharger rotor from 30 to 65 s while maintaining the normal operating mode of the turbocharger lubrication system
- Open Access
- 27 October 2021
- Published by EDP Sciences in BIO Web of Conferences
- Vol. 37, 00052
Justification of the parameter that determines the ability of turbochargers of agricultural machinery engines to function
As a result of the analysis of statistics on the main failures of the turbocharger of tractor engines in agricultural production, it can be concluded that it is the condition of its bearing node, in the first place, determines the performance of the entire turbocharger. This ultimately affects the duration of the turbocharger rotor after the engine stops. The article considers the method of determining the rotation time of the turbocharger rotor by inertia depending on the following factors: the time of the pressure drop in the turbocharger grease system, the gap in the turbocharger bearing node, the frequency of rotation of the rotor before the engine stops. The results of experimental studies on the timing of the turbocharger rotor rotation after the engine stop for the regular mode of greasing the bearing node and when using an individual lubricant system are presented. Based on the experimental values obtained, it is concluded that the main indicator of the performance of the turbocharger is the duration of rotation of its rotor after the engine stops and the application of the individual system of lubrication of the bearing node of the turbocharger reduces the cost of bearing resource and increases the resource of the entire turbocharger of agricultural machinery engines at least twice.
- 27 October 2021
- Published by EDP Sciences in BIO Web of Conferences
- Vol. 37, 00052
Open AccessJustification of the parameter that determines the ability of turbochargers of agricultural machinery engines to function
As a result of the analysis of statistics on the main failures of the turbocharger of tractor engines in agricultural production, it can be concluded that it is the condition of its bearing node, in the first place, determines the performance of the entire turbocharger. This ultimately affects the duration of the turbocharger rotor after the engine stops. The article considers the method of determining the rotation time of the turbocharger rotor by inertia depending on the following factors: the time of the pressure drop in the turbocharger grease system, the gap in the turbocharger bearing node, the frequency of rotation of the rotor before the engine stops. The results of experimental studies on the timing of the turbocharger rotor rotation after the engine stop for the regular mode of greasing the bearing node and when using an individual lubricant system are presented. Based on the experimental values obtained, it is concluded that the main indicator of the performance of the turbocharger is the duration of rotation of its rotor after the engine stops and the application of the individual system of lubrication of the bearing node of the turbocharger reduces the cost of bearing resource and increases the resource of the entire turbocharger of agricultural machinery engines at least twice.