Naqib Hakim Kamarudin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Naqib Hakim Kamarudin has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
A Azhari
Department of Manufacturing, Universiti Malaysia Pahang (UMP), 26600 Pekan, Pahang Malaysia
1 shared publicationA Mebrahitom
Department of Manufacturing, Universiti Malaysia Pahang (UMP), 26600 Pekan, Pahang Malaysia
1 shared publication- Ayyagari Kameswari Prasada Rao
GITAM (Deemed to be) University, Visakhapatnam, India
1 shared publication - Azmir Azhari
Chair of Design in Mechanical Engineering, University of Kaiserslautern, Kaiserslautern, Germany
1 shared publication
Latest Publications
- Open Access
- 29 January 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 290 (1) , 012069
Assembly meshing of abrasive waterjet nozzle erosion simulation
Computational Fluid Dynamics (CFD) softwares have been prevalent in Abrasive Waterjet (AWJ) Modelling for optimization and prediction. However, there are many different methods in approaching a single problem especially in predicting the erosion rate of nozzle which is critical in influencing kerf quality of AWJ cutting. In this paper, three main methods of assembly meshing for an abrasive waterjet erosion were simulated which is Quadrilateral, Cutcell and Tetrahedrons and each processing time, quality of convergence and accuracy of results are discussed. Results shows that Quadrilateral mesh prevails in the mentioned category followed by Tetrahedrons and Cutcell.
- 29 January 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 290 (1) , 012069
Open AccessAssembly meshing of abrasive waterjet nozzle erosion simulation
Computational Fluid Dynamics (CFD) softwares have been prevalent in Abrasive Waterjet (AWJ) Modelling for optimization and prediction. However, there are many different methods in approaching a single problem especially in predicting the erosion rate of nozzle which is critical in influencing kerf quality of AWJ cutting. In this paper, three main methods of assembly meshing for an abrasive waterjet erosion were simulated which is Quadrilateral, Cutcell and Tetrahedrons and each processing time, quality of convergence and accuracy of results are discussed. Results shows that Quadrilateral mesh prevails in the mentioned category followed by Tetrahedrons and Cutcell.
- Open Access
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012016
CFD Based Erosion Modelling of Abrasive Waterjet Nozzle using Discrete Phase Method
In Abrasive Waterjet (AWJ) machining, the nozzle is the most critical component that influences the performance, precision and economy. Exposure to a high speed jet and abrasives makes it susceptible to wear erosion which requires for frequent replacement. The present works attempts to simulate the erosion of the nozzle wall using computational fluid dynamics. The erosion rate of the nozzle was simulated under different operating conditions. The simulation was carried out in several steps which is flow modelling, particle tracking and erosion rate calculation. Discrete Phase Method (DPM) and K-ε turbulence model was used for the simulation. Result shows that different operating conditions affect the erosion rate as well as the flow interaction of water, air and abrasives. The simulation results correlates well with past work.
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012016
Open AccessCFD Based Erosion Modelling of Abrasive Waterjet Nozzle using Discrete Phase Method
In Abrasive Waterjet (AWJ) machining, the nozzle is the most critical component that influences the performance, precision and economy. Exposure to a high speed jet and abrasives makes it susceptible to wear erosion which requires for frequent replacement. The present works attempts to simulate the erosion of the nozzle wall using computational fluid dynamics. The erosion rate of the nozzle was simulated under different operating conditions. The simulation was carried out in several steps which is flow modelling, particle tracking and erosion rate calculation. Discrete Phase Method (DPM) and K-ε turbulence model was used for the simulation. Result shows that different operating conditions affect the erosion rate as well as the flow interaction of water, air and abrasives. The simulation results correlates well with past work.