Eduardo Preto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Eduardo Preto has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Samuel da Silva
Department of Mechanical Engineering, Universidade Estadual Paulista (UNESP), Ilha Solteira, Brazil
6 shared publications - Diogo Cunha José Karmouche
São Paulo State University – UNESP
3 shared publications - Gustavo Luiz Chagas Manhães de Abreu
Universidade Estadual Paulista - UNESP, FEIS, Dep. de Engenharia Mecânica, Ilha Solteira-SP
3 shared publications Beatriz Ambrozini
Departamento de Engenharia, Física e Matemática, Instituto de Química de Araraquara, Universidade Estadual Paulista (UNESP), Araraquara, São Paulo, Brasil
2 shared publications- Camilo Rocha Araújo
Unesp - Ilha Solteira
2 shared publications - Gaël Chevallier
Centre de recherche de l'Ecole de l'air et de l'espace 4 , 13660 Salon-de- Provence
2 shared publications
Latest Publications
- 12 October 2026
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
Experimental evaluation of PVB/ITO nanocomposite sensors for bending crack monitoring in metallic structures
Fatigue cracks in thin metallic structures subjected to bending can nucleate at multiple surface locations and propagate rapidly through the thickness, resulting in a brief interval between damage initiation and final failure. This study experimentally evaluates a piezoresistive sensor comprising indium tin oxide (ITO) nanowires dispersed in a polyvinyl butyral (PVB) matrix for real-time qualitative monitoring of this bending fatigue damage. Six structural steel specimens with a geometric stress concentrator were excited near their first bending resonance at frequencies between 28.5 and 29.5 Hz. Two sensor configurations were examined: two narrow nanocomposite strips, tested on four specimens, and one wider sensor covering the critical region, tested on two specimens. Specimens with narrow sensors failed between approximately 48,000 and 58,000 cycles, whereas the wider-sensor configuration failed near 45,000 cycles. In all four narrow-sensor tests, changes in the electrical response were detected prior to final structural failure. The wider sensors produced more stable electrical signals but showed lower sensitivity to localized damage, with significant changes occurring only shortly before or during specimen failure. This difference is attributed to the fewer parallel conductive pathways in the narrow sensors, which increases their sensitivity to localized disruptions in the ITO percolation network. The results demonstrate the feasibility of PVB/ITO nanocomposite sensors for real-time qualitative detection of rapidly evolving bending fatigue damage and highlight sensor geometry as a key parameter that influences damage sensitivity.
- 12 October 2026
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
Experimental evaluation of PVB/ITO nanocomposite sensors for bending crack monitoring in metallic structures
Fatigue cracks in thin metallic structures subjected to bending can nucleate at multiple surface locations and propagate rapidly through the thickness, resulting in a brief interval between damage initiation and final failure. This study experimentally evaluates a piezoresistive sensor comprising indium tin oxide (ITO) nanowires dispersed in a polyvinyl butyral (PVB) matrix for real-time qualitative monitoring of this bending fatigue damage. Six structural steel specimens with a geometric stress concentrator were excited near their first bending resonance at frequencies between 28.5 and 29.5 Hz. Two sensor configurations were examined: two narrow nanocomposite strips, tested on four specimens, and one wider sensor covering the critical region, tested on two specimens. Specimens with narrow sensors failed between approximately 48,000 and 58,000 cycles, whereas the wider-sensor configuration failed near 45,000 cycles. In all four narrow-sensor tests, changes in the electrical response were detected prior to final structural failure. The wider sensors produced more stable electrical signals but showed lower sensitivity to localized damage, with significant changes occurring only shortly before or during specimen failure. This difference is attributed to the fewer parallel conductive pathways in the narrow sensors, which increases their sensitivity to localized disruptions in the ITO percolation network. The results demonstrate the feasibility of PVB/ITO nanocomposite sensors for real-time qualitative detection of rapidly evolving bending fatigue damage and highlight sensor geometry as a key parameter that influences damage sensitivity.
- Open Access
- 24 August 2026
- Published by Elsevier in Measurement
- Vol. 290
Washer-shaped piezoresistive nanocomposite sensor for detecting tightness loss in bolted joints
- 24 August 2026
- Published by Elsevier in Measurement
- Vol. 290
Open AccessWasher-shaped piezoresistive nanocomposite sensor for detecting tightness loss in bolted joints
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
A Constitutive Model for Carbon Nanotube and Carbon Black Reinforced Rubber Nanocomposite Sensors Applied to Structural Health Monitoring
Piezoresistive nanocomposites have emerged as a promising alternative for structural monitoring, combining low sensor cost, simple fabrication and analysis, and real-time measurement capability. Despite advances in developing new nanocomposites and their experimental applications, there remains a gap in studies addressing the mathematical modeling of their electromechanical behavior. This work presents the development of a constitutive model for a piezoresistive nanocomposite composed of a natural rubber matrix reinforced with carbon nanotubes (CNT) and carbon black (CB), which has previously been employed to detect tightening loss in bolted joints with promising results. The sensor has a washer-shaped geometry and is installed between the bolt washer and the bolted joint interface, so that the deformation generated in the joint alters the electrical response of the sensor. Samples with different nanofiller proportions were fabricated and characterized to extract their piezoresistive properties. Mechanical stress and electrical conductivity under cyclic deformation were approximated by linear relationships whose coefficients varied with nanofiller concentration. Subsequently, a nonlinear formulation was proposed to describe the combined influence of CNT and CB on these coefficients. The model was calibrated using Bayesian inference, enabling the estimation of both conductivity and mechanical stress under various deformation conditions. The proposed constitutive model can be integrated into multiphysics simulation software, enabling virtual testing of the sensor within complex structures and optimizing its characteristics for different applications. The agreement between simulated and experimental results confirms the model’s capability to simulate and tune the sensitivity of nanocomposite sensors by adjusting CNT and CB contents, facilitating the design of customized real-time structural monitoring sensors for specific bolted joint configurations.
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
A Constitutive Model for Carbon Nanotube and Carbon Black Reinforced Rubber Nanocomposite Sensors Applied to Structural Health Monitoring
Piezoresistive nanocomposites have emerged as a promising alternative for structural monitoring, combining low sensor cost, simple fabrication and analysis, and real-time measurement capability. Despite advances in developing new nanocomposites and their experimental applications, there remains a gap in studies addressing the mathematical modeling of their electromechanical behavior. This work presents the development of a constitutive model for a piezoresistive nanocomposite composed of a natural rubber matrix reinforced with carbon nanotubes (CNT) and carbon black (CB), which has previously been employed to detect tightening loss in bolted joints with promising results. The sensor has a washer-shaped geometry and is installed between the bolt washer and the bolted joint interface, so that the deformation generated in the joint alters the electrical response of the sensor. Samples with different nanofiller proportions were fabricated and characterized to extract their piezoresistive properties. Mechanical stress and electrical conductivity under cyclic deformation were approximated by linear relationships whose coefficients varied with nanofiller concentration. Subsequently, a nonlinear formulation was proposed to describe the combined influence of CNT and CB on these coefficients. The model was calibrated using Bayesian inference, enabling the estimation of both conductivity and mechanical stress under various deformation conditions. The proposed constitutive model can be integrated into multiphysics simulation software, enabling virtual testing of the sensor within complex structures and optimizing its characteristics for different applications. The agreement between simulated and experimental results confirms the model’s capability to simulate and tune the sensitivity of nanocomposite sensors by adjusting CNT and CB contents, facilitating the design of customized real-time structural monitoring sensors for specific bolted joint configurations.
- Open Access
- 9 May 2026
- Published by Elsevier in SSRN Electronic Journal
Washer-Shaped Piezoresistive Nanocomposite Sensor for Detecting Tightness Loss in Bolted Joints
A novel method for detecting bolt tightness loss is introduced, utilizing real-time measurements from piezoresistive nanocomposite sensors. Piezoresistive sensors alter their electrical resistance in response to applied mechanical force. The sensor consists of natural rubber embedded with carbon nanowires and carbon black, which together facilitate electrical conductivity within the rubber matrix. When subjected to compressive or tensile loading, the composite exhibits a piezoresistive response, as the distribution of conductive nanomaterials shifts. Electrical characterization, including current and voltage measurements, was conducted to confirm and quantify this behavior. A washer-shaped sensor was fabricated and implemented to monitor bolted joints under two configurations: bolts arranged in a single direction and in two directions. Compressive deformation at the bolt interface resulted in measurable changes in the sensor’s electrical response as the applied torque varied. In both configurations, the sensor consistently detected torque variations, including in bolts that were not directly loosened, indicating its ability to monitor entire joints without instrumenting every bolt. Dynamic testing, involving variable loads and vibrations, demonstrated that the sensor did not significantly influence the structure’s dynamic properties, except when bolts were extremely loose. This approach reduces the cost and complexity of sensing, data acquisition, processing, and diagnosis, while offering greater sensitivity to torque variations than conventional techniques.
- 9 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessWasher-Shaped Piezoresistive Nanocomposite Sensor for Detecting Tightness Loss in Bolted Joints
A novel method for detecting bolt tightness loss is introduced, utilizing real-time measurements from piezoresistive nanocomposite sensors. Piezoresistive sensors alter their electrical resistance in response to applied mechanical force. The sensor consists of natural rubber embedded with carbon nanowires and carbon black, which together facilitate electrical conductivity within the rubber matrix. When subjected to compressive or tensile loading, the composite exhibits a piezoresistive response, as the distribution of conductive nanomaterials shifts. Electrical characterization, including current and voltage measurements, was conducted to confirm and quantify this behavior. A washer-shaped sensor was fabricated and implemented to monitor bolted joints under two configurations: bolts arranged in a single direction and in two directions. Compressive deformation at the bolt interface resulted in measurable changes in the sensor’s electrical response as the applied torque varied. In both configurations, the sensor consistently detected torque variations, including in bolts that were not directly loosened, indicating its ability to monitor entire joints without instrumenting every bolt. Dynamic testing, involving variable loads and vibrations, demonstrated that the sensor did not significantly influence the structure’s dynamic properties, except when bolts were extremely loose. This approach reduces the cost and complexity of sensing, data acquisition, processing, and diagnosis, while offering greater sensitivity to torque variations than conventional techniques.
- 20 November 2025
- Published by SAGE Publications in International Journal of Mechanical Engineering Education
Design-based laboratories for mechanical vibrations: Active learning approaches in engineering education
Engineering education increasingly demands active and practice-oriented learning approaches, particularly in domains such as mechanical vibrations where mathematical abstraction often limits student engagement. Traditional reliance on simulations and programming exercises has helped reduce costs but fails to expose students to the complete process of measurement, instrumentation, and signal interpretation. To address this gap, this work presents an experimental methodology developed for undergraduate education, focusing on practical vibration analysis through three structured projects. The activities involve instrumentation setup, vibration data acquisition, signal conversion and analysis, and identification of system parameters and behaviors. All experiments were conducted collaboratively with students, who then analyzed the collected data, interpreted results, and reported their findings. The methodology not only reinforced theoretical concepts but also improved student motivation, critical thinking, and familiarity with experimental practices that are typically absent from the curriculum. The proposed projects are low-cost, replicable in other academic settings, and accompanied by an open dataset that instructors may adapt for teaching and assessment. This contribution aims to bridge the gap between theory and practice, offering a scalable model to enhance learning outcomes in mechanical vibrations education.
- 20 November 2025
- Published by SAGE Publications in International Journal of Mechanical Engineering Education
Design-based laboratories for mechanical vibrations: Active learning approaches in engineering education
Engineering education increasingly demands active and practice-oriented learning approaches, particularly in domains such as mechanical vibrations where mathematical abstraction often limits student engagement. Traditional reliance on simulations and programming exercises has helped reduce costs but fails to expose students to the complete process of measurement, instrumentation, and signal interpretation. To address this gap, this work presents an experimental methodology developed for undergraduate education, focusing on practical vibration analysis through three structured projects. The activities involve instrumentation setup, vibration data acquisition, signal conversion and analysis, and identification of system parameters and behaviors. All experiments were conducted collaboratively with students, who then analyzed the collected data, interpreted results, and reported their findings. The methodology not only reinforced theoretical concepts but also improved student motivation, critical thinking, and familiarity with experimental practices that are typically absent from the curriculum. The proposed projects are low-cost, replicable in other academic settings, and accompanied by an open dataset that instructors may adapt for teaching and assessment. This contribution aims to bridge the gap between theory and practice, offering a scalable model to enhance learning outcomes in mechanical vibrations education.
- 16 April 2025
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 36 (8) , 531-542
Detection of torque variation in bolted joints structures using a new sensor made of natural rubber filled with carbon black and carbon nanotubes
Bolted joints are widely used in various sectors due to the ease of connecting two or more parts, but the loss of torque in the bolts of this connection can cause catastrophic failures. This article presents a new piezoresistive sensor composed of a nanocomposite material with rubber, carbon black, and carbon nanotubes designed for monitoring structural health in bolted joints using a new approach for detecting tightening variation. The sensor combines rubber-like flexibility with enhanced conductivity thanks to incorporating carbon nanostructures. The properties of the rubber are thoroughly examined, and the sensor is tested in various scenarios. Its behavior and resistive response are first evaluated under cyclic loading to assess durability and functional reliability. The sensor is also analyzed for its response to environmental effects such as temperature and humidity, and their influence on measurements is evaluated. After that, the sensor is studied as an automatic and static indicator for detecting torque variation when coupled with bolted joints in a structure. This application leverages the sensor’s ability to detect variations in electrical resistance caused by changes in tightening torque, providing a method for identifying such issues. The study indicates the new sensor reliably responds to cyclic loading with resistance variation. Environmental conditions can introduce variations in influence depending on the material’s conductivity level. The sensor was applied to a bolted joint, and the variation in bolt torque can be related to the variation in electrical resistance. In addition, the percentage of nanomaterials makes the sensor more or less sensitive to the torque level, making it possible to produce a sensor for different torque ranges. For the most sensitive sensor, there was a variation of 60% in the measurements after varying by 2 Nm. At the same time, the second, with more nanomaterials, changed the resistance by another 40% for a range of 6 Nm. Furthermore, its application in identifying tightening variations has proven sensitive and effective, successfully detecting torque variations in bolts.
- 16 April 2025
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 36 (8) , 531-542
Detection of torque variation in bolted joints structures using a new sensor made of natural rubber filled with carbon black and carbon nanotubes
Bolted joints are widely used in various sectors due to the ease of connecting two or more parts, but the loss of torque in the bolts of this connection can cause catastrophic failures. This article presents a new piezoresistive sensor composed of a nanocomposite material with rubber, carbon black, and carbon nanotubes designed for monitoring structural health in bolted joints using a new approach for detecting tightening variation. The sensor combines rubber-like flexibility with enhanced conductivity thanks to incorporating carbon nanostructures. The properties of the rubber are thoroughly examined, and the sensor is tested in various scenarios. Its behavior and resistive response are first evaluated under cyclic loading to assess durability and functional reliability. The sensor is also analyzed for its response to environmental effects such as temperature and humidity, and their influence on measurements is evaluated. After that, the sensor is studied as an automatic and static indicator for detecting torque variation when coupled with bolted joints in a structure. This application leverages the sensor’s ability to detect variations in electrical resistance caused by changes in tightening torque, providing a method for identifying such issues. The study indicates the new sensor reliably responds to cyclic loading with resistance variation. Environmental conditions can introduce variations in influence depending on the material’s conductivity level. The sensor was applied to a bolted joint, and the variation in bolt torque can be related to the variation in electrical resistance. In addition, the percentage of nanomaterials makes the sensor more or less sensitive to the torque level, making it possible to produce a sensor for different torque ranges. For the most sensitive sensor, there was a variation of 60% in the measurements after varying by 2 Nm. At the same time, the second, with more nanomaterials, changed the resistance by another 40% for a range of 6 Nm. Furthermore, its application in identifying tightening variations has proven sensitive and effective, successfully detecting torque variations in bolts.
- 24 March 2025
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 25 (4) , 2628-2642
Nanocomposite sensors with indium tin oxide nanowires in a polyvinyl butyral matrix for crack detection in structural health monitoring
We propose and test a novel sensor for structural health monitoring (SHM) based on a nanocomposite film consisting of indium tin oxide (ITO) nanowires embedded in a polyvinyl butyral (PVB) matrix to detect cracks. The sensor operates by measuring the electrical resistance between terminals when it is adhered to the surface of a structure. When damage mechanisms are present, the ITO nanowires either break or rearrange, causing a change in the sensor’s internal resistance. However, certain limitations must be addressed for broader applications. Among these, the effects of loading, humidity, and temperature fluctuations in the host structure pose significant challenges. Experimental tests were conducted to evaluate the environmental influences on measurements, revealing minimal data variation, indicating that these factors are not critical concerns. Additionally, sensitivity tests were performed to assess the sensor’s response to structural changes emulating damage mechanisms, and the sensor demonstrated accurate detection. In crack propagation experiments, the sensor detected cracks during their nucleation, propagation, and ultimate failure stages. The results show this novel sensor has strong potential for crack detection and monitoring applications. Another key advantage is the simplicity of signal collection and analysis, as measurements can be obtained through static readings without excitation signals in the structure. Furthermore, the sensor’s resistance correlates well with the extent of damage.
- 24 March 2025
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 25 (4) , 2628-2642
Nanocomposite sensors with indium tin oxide nanowires in a polyvinyl butyral matrix for crack detection in structural health monitoring
We propose and test a novel sensor for structural health monitoring (SHM) based on a nanocomposite film consisting of indium tin oxide (ITO) nanowires embedded in a polyvinyl butyral (PVB) matrix to detect cracks. The sensor operates by measuring the electrical resistance between terminals when it is adhered to the surface of a structure. When damage mechanisms are present, the ITO nanowires either break or rearrange, causing a change in the sensor’s internal resistance. However, certain limitations must be addressed for broader applications. Among these, the effects of loading, humidity, and temperature fluctuations in the host structure pose significant challenges. Experimental tests were conducted to evaluate the environmental influences on measurements, revealing minimal data variation, indicating that these factors are not critical concerns. Additionally, sensitivity tests were performed to assess the sensor’s response to structural changes emulating damage mechanisms, and the sensor demonstrated accurate detection. In crack propagation experiments, the sensor detected cracks during their nucleation, propagation, and ultimate failure stages. The results show this novel sensor has strong potential for crack detection and monitoring applications. Another key advantage is the simplicity of signal collection and analysis, as measurements can be obtained through static readings without excitation signals in the structure. Furthermore, the sensor’s resistance correlates well with the extent of damage.
- 20 July 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 32 (9) , 095001
Experimental investigation of vibration control of flexible rotors using shape memory alloys
Vibration is an essential subject for the design of rotordynamic systems, being responsible for compromising the integrity and causing risks to operational functioning. This work deals with an experimental investigation of the semi-active vibration controller for a rotordynamic system using shape memory alloy (SMA) elements. SMAs are smart materials that present thermomechanical coupling represented by solid phase transformations that promote either stiffness change or hysteretic dissipation. In this regard, they are useful in controllers employing thermal actuation from electric current through the Joule effect. This paper presents a proof of concept of a controller using SMA elements. An experimental apparatus is proposed considering a typical rotor system using SMA wires at the bearings. In this regard, proper temperature variations allow the system to cross critical resonant conditions.
- 20 July 2023
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 32 (9) , 095001
Experimental investigation of vibration control of flexible rotors using shape memory alloys
Vibration is an essential subject for the design of rotordynamic systems, being responsible for compromising the integrity and causing risks to operational functioning. This work deals with an experimental investigation of the semi-active vibration controller for a rotordynamic system using shape memory alloy (SMA) elements. SMAs are smart materials that present thermomechanical coupling represented by solid phase transformations that promote either stiffness change or hysteretic dissipation. In this regard, they are useful in controllers employing thermal actuation from electric current through the Joule effect. This paper presents a proof of concept of a controller using SMA elements. An experimental apparatus is proposed considering a typical rotor system using SMA wires at the bearings. In this regard, proper temperature variations allow the system to cross critical resonant conditions.
- Open Access
- 1 January 2021
- Published by SWGE Sistemas Ltda in Procedings Do Xv Simpósio Brasileiro de Automação Inteligente
- Vol. 1 (1)
Análise de controle via algoritmo particle swarm optimization
Metaheuristic algorithms have become popular lately as an optimization method due to their similarity to natural adaptation events. In this context, such algorithms have the ability to cover several areas, in which for control systems such algorithms present a new way of developing and adapting control laws that are adapted and improved for different situations in which the dynamic system can be found. This work aims to present the metaheuristic algorithm particle swarm optimization in which three populations of gains, generated in different ways, are optimized by the algorithm and adapted by the same for different situations of parameters of the analyzed system.
- 1 January 2021
- Published by SWGE Sistemas Ltda in Procedings Do Xv Simpósio Brasileiro de Automação Inteligente
- Vol. 1 (1)
Open AccessAnálise de controle via algoritmo particle swarm optimization
Metaheuristic algorithms have become popular lately as an optimization method due to their similarity to natural adaptation events. In this context, such algorithms have the ability to cover several areas, in which for control systems such algorithms present a new way of developing and adapting control laws that are adapted and improved for different situations in which the dynamic system can be found. This work aims to present the metaheuristic algorithm particle swarm optimization in which three populations of gains, generated in different ways, are optimized by the algorithm and adapted by the same for different situations of parameters of the analyzed system.