Arun Kumar Shrivastav
Research Subjects
Arun Kumar Shrivastav has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Indhumathi Kulandhaisamy
Saveetha Engineeering College
3 shared publications - Malathi Kanagasabai
Department of Electronics and Communication Engineering , Rajalakshmi Engineering College , Thandalam , Tamil Nadu , India
2 shared publications Gulam Nabi Alsath
ECE Department, SSN College of Engineering, India
1 shared publicationIndira Gandhi Sannasi
ECE Department, MIT, India
1 shared publication- Jayaram Kizhekke Pakkathillam
Center for Nondestructive Evaluation, Iowa State University, Ames, IA, USA
1 shared publication Kalaivani C T
Saveetha Engineering College,Department of Electronics Communication Engg.,Chennai,India
1 shared publication
Latest Publications
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1021-1025
Vivaldi Antenna Implementation for Rescue and See-Through-Wall Applications
High Gain Ultra wide band Vivaldi antenna with a single array tapered slot Vivaldi antenna element designed, fabricated and validated in this research at a 2.4 GHz frequency. The Gain of the fabricated antenna remain constant with the change in frequency. In practically the alteration from micro strip to slot line in this research design limits the further extension of impedance bandwidth. A minor change in the construction of this antenna is done to overcome this disadvantage by limiting factor of the antenna is made to achieve the required bandwidth. The frequency and power gain can be increased by multiple combination of this array as the feed forward antenna. The VSWR is a measure of efficiency of transmission from a power source to the receiver in a desired direction. VSWR helps in measuring the voltage adjustments. The voltage doesn't differ in a perfect system and its VSWR is 1.0. The fabricated tapered slot Vivaldi antenna using FR4 material. This fabricated antenna can be used for see through wall and recuse applications, which is test by single antenna parameter and verify the desirability of the antenna for UWB systems for see through wall applications.
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1021-1025
Vivaldi Antenna Implementation for Rescue and See-Through-Wall Applications
High Gain Ultra wide band Vivaldi antenna with a single array tapered slot Vivaldi antenna element designed, fabricated and validated in this research at a 2.4 GHz frequency. The Gain of the fabricated antenna remain constant with the change in frequency. In practically the alteration from micro strip to slot line in this research design limits the further extension of impedance bandwidth. A minor change in the construction of this antenna is done to overcome this disadvantage by limiting factor of the antenna is made to achieve the required bandwidth. The frequency and power gain can be increased by multiple combination of this array as the feed forward antenna. The VSWR is a measure of efficiency of transmission from a power source to the receiver in a desired direction. VSWR helps in measuring the voltage adjustments. The voltage doesn't differ in a perfect system and its VSWR is 1.0. The fabricated tapered slot Vivaldi antenna using FR4 material. This fabricated antenna can be used for see through wall and recuse applications, which is test by single antenna parameter and verify the desirability of the antenna for UWB systems for see through wall applications.
- 28 September 2015
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 9 (1) , 71-77
A planar microwave phase shifter using microstrip–CPW–microstrip transition with defected ground structures
A novel planar printed phase shifter design is proposed in this paper. The design is developed with microstrip–conductor-backed coplanar waveguide– microstrip (MP–CBCPW–MP) transition line with different defected ground structures (DGS). The differential phase shift can be controlled by altering the DGS dimensions. Three prototypes with DGS dimensions 5 × 10, 10 × 20, and 10 × 30 mm2, are employed at the finite ground plane to achieve 5°, 20°, and 30° shift in phase respectively and are validated with the phase delay relation. The prominent effect of the transition region is to confine the field area. The resonance is at 700 MHz with a bandwidth of 400 MHz (0.4–0.8 GHz). The proposed phase shifter can be used for broadcasting applications. The proposed MP–CBCPW–MP transition phase shifter design with DGS is simulated, fabricated, and measured to analyze its performance.
- 28 September 2015
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 9 (1) , 71-77
A planar microwave phase shifter using microstrip–CPW–microstrip transition with defected ground structures
A novel planar printed phase shifter design is proposed in this paper. The design is developed with microstrip–conductor-backed coplanar waveguide– microstrip (MP–CBCPW–MP) transition line with different defected ground structures (DGS). The differential phase shift can be controlled by altering the DGS dimensions. Three prototypes with DGS dimensions 5 × 10, 10 × 20, and 10 × 30 mm2, are employed at the finite ground plane to achieve 5°, 20°, and 30° shift in phase respectively and are validated with the phase delay relation. The prominent effect of the transition region is to confine the field area. The resonance is at 700 MHz with a bandwidth of 400 MHz (0.4–0.8 GHz). The proposed phase shifter can be used for broadcasting applications. The proposed MP–CBCPW–MP transition phase shifter design with DGS is simulated, fabricated, and measured to analyze its performance.
- 20 August 2015
- Published by Taylor & Francis in Waves in Random and Complex Media
- Vol. 25 (4) , 669-681
Triband phase shifter design using split-ring resonator and complementary split-ring resonator-loaded ground plane for wireless applications
This paper presents the design of a novel linear analog planar phase shifter deploying split-ring resonator (SRR) and complementary split-ring resonator (CSRR) structures. Based on the advantages of these structures, a triband phase shifter is designed for multiple target systems to operate at 0.85, 1.69, and 2.46 GHz bands finding applications for European RFIDs, Satellite Radio Broadcast System, Mobile Services, and ISM Band, respectively. The effect of SRR and CSRR coupling with host transmission line is also analyzed on the basis of Bloch mode theory and the modes are validated through Eigen mode analysis. The proposed phase shifter design shows a good agreement between simulated and measured results. A 90° ± 8° shift in phase is observed at lower and upper bands, and a 135° ± 8° shift is observed in center band with reasonable group delay components.
- 20 August 2015
- Published by Taylor & Francis in Waves in Random and Complex Media
- Vol. 25 (4) , 669-681
Triband phase shifter design using split-ring resonator and complementary split-ring resonator-loaded ground plane for wireless applications
This paper presents the design of a novel linear analog planar phase shifter deploying split-ring resonator (SRR) and complementary split-ring resonator (CSRR) structures. Based on the advantages of these structures, a triband phase shifter is designed for multiple target systems to operate at 0.85, 1.69, and 2.46 GHz bands finding applications for European RFIDs, Satellite Radio Broadcast System, Mobile Services, and ISM Band, respectively. The effect of SRR and CSRR coupling with host transmission line is also analyzed on the basis of Bloch mode theory and the modes are validated through Eigen mode analysis. The proposed phase shifter design shows a good agreement between simulated and measured results. A 90° ± 8° shift in phase is observed at lower and upper bands, and a 135° ± 8° shift is observed in center band with reasonable group delay components.
- 25 June 2015
- Published by Taylor & Francis in Waves in Random and Complex Media
- Vol. 25 (4) , 457-472
A substrate-modified CPW-based linear microwave phase shifter
A novel method for achieving linear phase shift is proposed over the frequency range of 2 - 6 GHz. Dielectric characterization of FR4 substrate interfaced with air as well as water produces the phase shift. The substrate property is modified by introducing a plain rectangular packet and W-shaped packet within the FR4 substrate. The overall dimension of the proposed structure is 30 × 60 mm2. Across the entire proposed frequency range, the reflection coefficient is less than −10 dB. The proposed coplanar waveguide with water- and air-stacked FR4 substrate is simulated, fabricated, and measured for its linear phase shifting characteristics analyzed in ISM 2.45, 3.3, and 5.8 GHz bands. The analysis over the entire band depicts that the differential shift in phase is directly proportional to the effective dielectric constant of the material used. The design will be more useful in automotive anti-collision radars in military, cellular base stations, and satellite communications.
- 25 June 2015
- Published by Taylor & Francis in Waves in Random and Complex Media
- Vol. 25 (4) , 457-472
A substrate-modified CPW-based linear microwave phase shifter
A novel method for achieving linear phase shift is proposed over the frequency range of 2 - 6 GHz. Dielectric characterization of FR4 substrate interfaced with air as well as water produces the phase shift. The substrate property is modified by introducing a plain rectangular packet and W-shaped packet within the FR4 substrate. The overall dimension of the proposed structure is 30 × 60 mm2. Across the entire proposed frequency range, the reflection coefficient is less than −10 dB. The proposed coplanar waveguide with water- and air-stacked FR4 substrate is simulated, fabricated, and measured for its linear phase shifting characteristics analyzed in ISM 2.45, 3.3, and 5.8 GHz bands. The analysis over the entire band depicts that the differential shift in phase is directly proportional to the effective dielectric constant of the material used. The design will be more useful in automotive anti-collision radars in military, cellular base stations, and satellite communications.