Chuankai Jing
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chuankai Jing has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Bin Wang
College of Mechanical and Electronic Engineering China University of Petroleum (East China) Qingdao China
2 shared publications - Fenna Zhang
College of Mechanical and Electronic Engineering, China University of Petroleum (East China), Qingdao 266580, China
2 shared publications - Fenna Zhang
College of Mechanical and Electronic Engineering, China University of Petroleum (East China), Qingdao 266580, China
2 shared publications - Hao Hu
China United Coalbed Methane Corporation Ltd., Beijing 100015, China
2 shared publications Bin Wang
College of Mechanical and Electronic Engineering, China University of Petroleum (East China), Qingdao, China
1 shared publicationFen-Na Zhang
College of Mechanical and Electronic Engineering, China University of Petroleum (East China), Qingdao, China
1 shared publication
Latest Publications
- Open Access
Low-Frequency Corrosion Fatigue Test Study of Sucker Rods under High-Salinity Well Fluids in Deep CBM Wells
Corrosion fatigue test is the most direct and effective method to study the corrosion fatigue characteristics of sucker rod. At present, the commonly used test method is the high frequency fatigue test, but the working state of sucker rod is typical low-frequency and high-cycle corrosion fatigue, and the test with high frequency will reduce the impact of corrosion. Alloy steel 4330 is widely used in coalbed gas well high strength sucker rod, but the research on its low frequency corrosion fatigue life is relatively few. Therefore, in this paper, the corrosion fatigue test method of axial low-frequency and high-cycle was adopted to study the corrosion fatigue characteristics of 4330 steel sucker rod through the corrosion fatigue test under different typical corrosion media, temperature, and stress levels. The results show that the fatigue life of 4330 sucker rod drops sharply when the Cl− concentration in high salinity well fluid exceeds the threshold value of 155 mg/L. When this threshold is exceeded, the downward trend slows down. It can be seen that the significant factor affecting the corrosion fatigue life of 4330 material is not the concentration of Cl−, but the existence of Cl−. The presence of HCO3− promotes a further decrease in the corrosion fatigue life of the 4330 sucker rod by Cl−. The corrosion fatigue life of 4330 sucker rod decreases with the increase of temperature. When the well fluid temperature is less than 50 °C, the impact is relatively significant. When the well fluid temperature is more than 70 °C, the decline trend of corrosion fatigue life slows down. Based on the fitted S-N curve (stress-fatigue life curve), it is calculated that the fatigue limit of 4330 sucker rod at the stress ratio of 0.6 is 196 MPa in the solution of 10,000 mg/L Cl− at room temperature. These could provide valuable theoretical and technical guidance for design and selection of high-strength sucker rod in high-salinity corrosion well fluid environment.
Open AccessLow-Frequency Corrosion Fatigue Test Study of Sucker Rods under High-Salinity Well Fluids in Deep CBM Wells
Corrosion fatigue test is the most direct and effective method to study the corrosion fatigue characteristics of sucker rod. At present, the commonly used test method is the high frequency fatigue test, but the working state of sucker rod is typical low-frequency and high-cycle corrosion fatigue, and the test with high frequency will reduce the impact of corrosion. Alloy steel 4330 is widely used in coalbed gas well high strength sucker rod, but the research on its low frequency corrosion fatigue life is relatively few. Therefore, in this paper, the corrosion fatigue test method of axial low-frequency and high-cycle was adopted to study the corrosion fatigue characteristics of 4330 steel sucker rod through the corrosion fatigue test under different typical corrosion media, temperature, and stress levels. The results show that the fatigue life of 4330 sucker rod drops sharply when the Cl− concentration in high salinity well fluid exceeds the threshold value of 155 mg/L. When this threshold is exceeded, the downward trend slows down. It can be seen that the significant factor affecting the corrosion fatigue life of 4330 material is not the concentration of Cl−, but the existence of Cl−. The presence of HCO3− promotes a further decrease in the corrosion fatigue life of the 4330 sucker rod by Cl−. The corrosion fatigue life of 4330 sucker rod decreases with the increase of temperature. When the well fluid temperature is less than 50 °C, the impact is relatively significant. When the well fluid temperature is more than 70 °C, the decline trend of corrosion fatigue life slows down. Based on the fitted S-N curve (stress-fatigue life curve), it is calculated that the fatigue limit of 4330 sucker rod at the stress ratio of 0.6 is 196 MPa in the solution of 10,000 mg/L Cl− at room temperature. These could provide valuable theoretical and technical guidance for design and selection of high-strength sucker rod in high-salinity corrosion well fluid environment.
- Open Access
A Wellbore Pressure Control Method for Two-Layer Coal Seam Gas Coproduction Wells
In coal seam gas (CSG) coproduction wells, due to the different production pressures of CSG production layer at different depths, the interlayer interference in wellbore seriously affects the gas production of a coproduction well. To effectively suppress the interlayer interference of the wellbore, a wellbore pressure distribution method for a two-layer coproduction well is proposed. Based on the analysis of the factors influencing the flow pressure distribution in the wellbore of two-layer coproduction wells, a method of coproduction flow pressure adjustment by regulating the wellhead pressure and the depth of the dynamic fluid level was established in this paper. The results show that wellhead pressure can directly affect the production pressure of two layers. The variation in layer 1 output mainly affects the pressure difference between the wellhead pressure and the pressure at the depth of layer 1, which has little effect on the pressure difference between layer 1 and 2. An increase in gas production from layer 2 would not only cause a pressure increase in layer 1, but also result in a reduction of the production pressure at layer 2. The maximum pressure gradient of the gas section is 0.14 MPa/100 m, and the pressure gradient of the gas–liquid section is 0.53–1.0 MPa/100 m.
Open AccessA Wellbore Pressure Control Method for Two-Layer Coal Seam Gas Coproduction Wells
In coal seam gas (CSG) coproduction wells, due to the different production pressures of CSG production layer at different depths, the interlayer interference in wellbore seriously affects the gas production of a coproduction well. To effectively suppress the interlayer interference of the wellbore, a wellbore pressure distribution method for a two-layer coproduction well is proposed. Based on the analysis of the factors influencing the flow pressure distribution in the wellbore of two-layer coproduction wells, a method of coproduction flow pressure adjustment by regulating the wellhead pressure and the depth of the dynamic fluid level was established in this paper. The results show that wellhead pressure can directly affect the production pressure of two layers. The variation in layer 1 output mainly affects the pressure difference between the wellhead pressure and the pressure at the depth of layer 1, which has little effect on the pressure difference between layer 1 and 2. An increase in gas production from layer 2 would not only cause a pressure increase in layer 1, but also result in a reduction of the production pressure at layer 2. The maximum pressure gradient of the gas section is 0.14 MPa/100 m, and the pressure gradient of the gas–liquid section is 0.53–1.0 MPa/100 m.
- Open Access
Study on Variable Stress Corrosion Susceptibility of Four Typical High-Strength Sucker Rods in High-Salinity Well Fluids
To study the corrosion characteristics of high-strength sucker rods in high-salinity well fluids under alternating stresses, a single-factor stress corrosion test was designed. The slow strain rate tensile test (SSRT) was carried out for four kinds of high-strength sucker rods under different Cl− and HCO3− concentrations and with different service strengths, and the variable stress corrosion cracking susceptibility was analyzed. The results show that the elongation loss and absorbed work loss of the H-grade ultra-high-strength 4330 sucker rod after stress corrosion are greater than those of both the high-strength 4142 sucker rod and the high-strength 20CrMoA sucker rod. The elongation and absorbed work loss of the 30CrMoA and 20CrMoA sucker rods are less affected by the changes in Cl− and HCO3−. With the increase in use strength, the elongation and absorbed work loss of the high-strength sucker rod increase. The change in the surface of the sucker rod during the corrosion process is inconsistent with the actual elongation of the sucker rod and the absorbed work loss. It can be concluded that the stress corrosion cracking susceptibility of the sucker rod is not necessarily related to the tensile strength of the sucker rod. The 4330 sucker rod is not suitable for applications in wells with a high concentration of Cl−, but it is suitable for operation in alkaline conditions where corrosive media such as HCO3− and Cl− coexist. Under highly corrosive and highly mineralized conditions, the 30CrMoA sucker rod is less susceptible to stress corrosion. The stress corrosion cracking susceptibility of the 20CrMoA sucker rod is lower than that of the 4142 sucker rod. In high-salinity well fluids, the higher the use strength, the higher the stress corrosion cracking susceptibility of the high-strength sucker rod is. The test results for the weight-loss-based corrosion rate and plastic loss may contradict the determination of the corrosion susceptibility of the material under working conditions.
Open AccessStudy on Variable Stress Corrosion Susceptibility of Four Typical High-Strength Sucker Rods in High-Salinity Well Fluids
To study the corrosion characteristics of high-strength sucker rods in high-salinity well fluids under alternating stresses, a single-factor stress corrosion test was designed. The slow strain rate tensile test (SSRT) was carried out for four kinds of high-strength sucker rods under different Cl− and HCO3− concentrations and with different service strengths, and the variable stress corrosion cracking susceptibility was analyzed. The results show that the elongation loss and absorbed work loss of the H-grade ultra-high-strength 4330 sucker rod after stress corrosion are greater than those of both the high-strength 4142 sucker rod and the high-strength 20CrMoA sucker rod. The elongation and absorbed work loss of the 30CrMoA and 20CrMoA sucker rods are less affected by the changes in Cl− and HCO3−. With the increase in use strength, the elongation and absorbed work loss of the high-strength sucker rod increase. The change in the surface of the sucker rod during the corrosion process is inconsistent with the actual elongation of the sucker rod and the absorbed work loss. It can be concluded that the stress corrosion cracking susceptibility of the sucker rod is not necessarily related to the tensile strength of the sucker rod. The 4330 sucker rod is not suitable for applications in wells with a high concentration of Cl−, but it is suitable for operation in alkaline conditions where corrosive media such as HCO3− and Cl− coexist. Under highly corrosive and highly mineralized conditions, the 30CrMoA sucker rod is less susceptible to stress corrosion. The stress corrosion cracking susceptibility of the 20CrMoA sucker rod is lower than that of the 4142 sucker rod. In high-salinity well fluids, the higher the use strength, the higher the stress corrosion cracking susceptibility of the high-strength sucker rod is. The test results for the weight-loss-based corrosion rate and plastic loss may contradict the determination of the corrosion susceptibility of the material under working conditions.
- Open Access
- 12 July 2023
- Published by SAGE Publications in Energy Exploration & Exploitation
- Vol. 42 (1) , 3-16
Modeling and characteristic analysis of viscous resistance in annulus gap of coalbed gas well drainage pump
The viscous resistance caused by the relative motion of plunger and pump barrel is an important factor in the dynamic analysis of the drainage and production mechanism during coalbed methane exploitation. Existing studies mostly focus on deep well (1000–3000 m) large-displacement pump (usually 80–300 m3/d), and the interstitial medium is mainly crude oil. Regression fitting is mainly carried out based on empirical formula or experimental simulation method, without considering the characteristics of shallower coalbed gas well (400–800 m) small-displacement pump (3/d). The variation of the clearance between plunger and barrel and the variation of viscous resistance between plunger and barrel are not revealed. Based on the Navier-Stokes equation and Newton's internal friction law, a mathematical model of the annular viscous resistance between the plunger and the pump barrel is established, and an analytical method is used to describe the influence of stroke times, annular clearance, and differential pressure between the upper and lower plungers on the viscous resistance. The results show that the plunger stroke is directly proportional to the variation range of viscous resistance, and low stroke is beneficial to reduce the viscous resistance. The effect of differential pressure between upper and lower plunger of rod pump on viscous resistance of small displacement coalbed gas well is significantly greater than that of plunger running speed. The annular clearance is directly proportional to the differential pressure between the upper and lower parts of the plunger, the inertia force of the plunger, and the shear force of the moving fluid. The annular viscous resistance model between plunger and pump barrel is helpful to improve the calculation accuracy of suspending point load of coalbed gas well pumping unit, analyze the working condition of coalbed gas drainage gas production process, and provide basis for the optimization design of coalbed gas well rod pump clearance.
- 12 July 2023
- Published by SAGE Publications in Energy Exploration & Exploitation
- Vol. 42 (1) , 3-16
Open AccessModeling and characteristic analysis of viscous resistance in annulus gap of coalbed gas well drainage pump
The viscous resistance caused by the relative motion of plunger and pump barrel is an important factor in the dynamic analysis of the drainage and production mechanism during coalbed methane exploitation. Existing studies mostly focus on deep well (1000–3000 m) large-displacement pump (usually 80–300 m3/d), and the interstitial medium is mainly crude oil. Regression fitting is mainly carried out based on empirical formula or experimental simulation method, without considering the characteristics of shallower coalbed gas well (400–800 m) small-displacement pump (3/d). The variation of the clearance between plunger and barrel and the variation of viscous resistance between plunger and barrel are not revealed. Based on the Navier-Stokes equation and Newton's internal friction law, a mathematical model of the annular viscous resistance between the plunger and the pump barrel is established, and an analytical method is used to describe the influence of stroke times, annular clearance, and differential pressure between the upper and lower plungers on the viscous resistance. The results show that the plunger stroke is directly proportional to the variation range of viscous resistance, and low stroke is beneficial to reduce the viscous resistance. The effect of differential pressure between upper and lower plunger of rod pump on viscous resistance of small displacement coalbed gas well is significantly greater than that of plunger running speed. The annular clearance is directly proportional to the differential pressure between the upper and lower parts of the plunger, the inertia force of the plunger, and the shear force of the moving fluid. The annular viscous resistance model between plunger and pump barrel is helpful to improve the calculation accuracy of suspending point load of coalbed gas well pumping unit, analyze the working condition of coalbed gas drainage gas production process, and provide basis for the optimization design of coalbed gas well rod pump clearance.