Zhe Wang
Zhe Wang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Chunsheng Wang
PetroChina Tarim Oilfield Company, Korla 841000, China
2 shared publications - Fengqi Wei
China National Petroleum Corporation Exploration and Production Company, Beijing 100007, China
1 shared publication - Han Zhao
CNPC Chuanqing Drilling Engineering Co., Ltd., Chengdu 610051, China
1 shared publication - Jian Cui
Changqing Branch, China National Petroleum Corporation China National Logging Corporation, Xi’an 710201, China
1 shared publication - Jinli Zhu
CNPC Bohai Equipment Manufacturing Co., Ltd., Tianjin 300456, China
1 shared publication - Lihong Han
State Key Laboratory of Oil and Gas Equipment, CNPC Tubular Goods Research Institute, Xi’an, China
1 shared publication
Latest Publications
- Open Access
Dynamic Response Mechanism and Risk Assessment of Threaded Connections During Jarring Operations in Ultra-Deep Wells
With the frequent occurrence of stuck pipe incidents during the ultra-deep well drilling operation, the hydraulic-while-drilling (HWD) jar has become a critical component of the bottom hole assembly (BHA). However, during jarring operations for stuck pipe release, the drill string experiences severe vibrations induced by the impact loads from the jar, which significantly alter the stress state and dynamic response of the threaded connections—the structurally weakest elements—under cyclic dynamic loading, often leading to fracture failures. here, a thread failure incident of a hydraulic jar in an ultra-deep well in the Tarim Basin, Xinjiang, is investigated. A drill string dynamic impact model incorporating the actual three-dimensional wellbore trajectory is established to capture the time-history characteristics of multi-axial loads at the threaded connection during up and down jarring. Meanwhile, a three-dimensional finite element model of a double-shouldered threaded connection with helix angle is developed, and the stress distribution of the joint thread is analyzed on the boundary condition acquired from the time-history characteristics of multi-axial loads. Numerical results indicate that the axial compression induces local bending of the drill string during down jarring, resulting in significantly greater bending moment fluctuations than in up jarring and a correspondingly higher amplitude of circumferential acceleration at the thread location. Among all thread positions, the first thread root at the pin end consistently experiences the highest average stress and stress variation, rendering it most susceptible to fatigue failure. This study provides theoretical and practical insights for optimizing drill string design and enhancing the reliability of threaded connections in deep and ultra-deep well drilling.
Open AccessDynamic Response Mechanism and Risk Assessment of Threaded Connections During Jarring Operations in Ultra-Deep Wells
With the frequent occurrence of stuck pipe incidents during the ultra-deep well drilling operation, the hydraulic-while-drilling (HWD) jar has become a critical component of the bottom hole assembly (BHA). However, during jarring operations for stuck pipe release, the drill string experiences severe vibrations induced by the impact loads from the jar, which significantly alter the stress state and dynamic response of the threaded connections—the structurally weakest elements—under cyclic dynamic loading, often leading to fracture failures. here, a thread failure incident of a hydraulic jar in an ultra-deep well in the Tarim Basin, Xinjiang, is investigated. A drill string dynamic impact model incorporating the actual three-dimensional wellbore trajectory is established to capture the time-history characteristics of multi-axial loads at the threaded connection during up and down jarring. Meanwhile, a three-dimensional finite element model of a double-shouldered threaded connection with helix angle is developed, and the stress distribution of the joint thread is analyzed on the boundary condition acquired from the time-history characteristics of multi-axial loads. Numerical results indicate that the axial compression induces local bending of the drill string during down jarring, resulting in significantly greater bending moment fluctuations than in up jarring and a correspondingly higher amplitude of circumferential acceleration at the thread location. Among all thread positions, the first thread root at the pin end consistently experiences the highest average stress and stress variation, rendering it most susceptible to fatigue failure. This study provides theoretical and practical insights for optimizing drill string design and enhancing the reliability of threaded connections in deep and ultra-deep well drilling.
- Open Access
Mechanism and Experimental Research on Rock Breaking by Cutting Teeth of High-Speed PDC Drill Bit
In order to study the breaking mechanism of rock of high-speed PDC drill bits, improve the cutting efficiency of cutting teeth, and reduce the wear of cutting teeth, the rock-breaking process of PDC cutting teeth is simulated based on mechanical theory knowledge and experiments in this paper. And the influence of changes in PDC tooth rake angle, cutting depth, and diameter of the cutting tooth was studied by changing the different structural and cutting parameters of the cutting teeth, as well as the changes in cutting force, frictional resistance stress, and contact pressure on PDC teeth during the cutting process. The simulated results show that the total energy of the system increases, and the total energy of the system is the largest when cutting at 45°, which coincides with the maximum contact pressure on the teeth at this time. At the same time, it also shows that the impact resistance of PDC teeth is the strongest when chamfered at 45°. The contact area is also smaller, so the cutting is more conducive to the cutting tooth eating into the formation and prolonging the service life of the cutting tooth when the tooth rake angle is 20°. The experimental results showed that, in the actual design of PDC drill bits, an appropriate smaller side angle is not only beneficial for chip removal, but also helps to prevent lateral vibration and does not have a significant impact on cutting load. Finally, obtaining the relationship curve between structural parameters and rock properties is of great significance for guiding the design of PDC drill bits, understanding the intrinsic mechanism of rock fragmentation, and revealing the macroscopic nonlinear mechanical behavior of rocks.
Open AccessMechanism and Experimental Research on Rock Breaking by Cutting Teeth of High-Speed PDC Drill Bit
In order to study the breaking mechanism of rock of high-speed PDC drill bits, improve the cutting efficiency of cutting teeth, and reduce the wear of cutting teeth, the rock-breaking process of PDC cutting teeth is simulated based on mechanical theory knowledge and experiments in this paper. And the influence of changes in PDC tooth rake angle, cutting depth, and diameter of the cutting tooth was studied by changing the different structural and cutting parameters of the cutting teeth, as well as the changes in cutting force, frictional resistance stress, and contact pressure on PDC teeth during the cutting process. The simulated results show that the total energy of the system increases, and the total energy of the system is the largest when cutting at 45°, which coincides with the maximum contact pressure on the teeth at this time. At the same time, it also shows that the impact resistance of PDC teeth is the strongest when chamfered at 45°. The contact area is also smaller, so the cutting is more conducive to the cutting tooth eating into the formation and prolonging the service life of the cutting tooth when the tooth rake angle is 20°. The experimental results showed that, in the actual design of PDC drill bits, an appropriate smaller side angle is not only beneficial for chip removal, but also helps to prevent lateral vibration and does not have a significant impact on cutting load. Finally, obtaining the relationship curve between structural parameters and rock properties is of great significance for guiding the design of PDC drill bits, understanding the intrinsic mechanism of rock fragmentation, and revealing the macroscopic nonlinear mechanical behavior of rocks.
- Open Access
Failure Analysis of Casing in Shale Oil Wells under Multistage Fracturing Conditions
During the multistage fracturing in shale oil and gas wells with tieback and liner, one of the major challenges is the wellbore temperature variation due to the high-rate fracturing. In such a case, the axial shrinkage trend of the casing string could be caused due to the sudden drop in temperature, but the actual axial length of the casing string would not change due to the cement constraints. Therefore, this could lead to cementation damage between the casing and cement due to excessive load from the casing string. A wellbore seal that is out of control often leads to irreversible consequences, even well abandonment. In order to study the mechanism of casing deformation in shale oil and gas wells with tieback and liner quantitatively, in this paper, take LS1 well (a typical shale oil and gas well with tieback and liner, and casing deformation is caused) for example, the transient changes of temperature and pressure in the whole wellbore during multistage fracturing are studied. Moreover, the cementing strength test of the interface between casing and cement is also tested. Then, the testing results are carried out and extended to model the finite element (FE) model with the whole vertical section casing string with tieback and liner. The model is used to simulate the internal force changes under fracturing conditions with different stages of fracturing. Meanwhile, the casing deformation mechanism in LS1 well is analyzed and studied in detail. Our simulation results indicated the failure process and mechanism of cementation between casing and cement in shale oil and gas wells with tieback and liner. Our work can provide a detailed theoretical reference and a basis for field application.
Open AccessFailure Analysis of Casing in Shale Oil Wells under Multistage Fracturing Conditions
During the multistage fracturing in shale oil and gas wells with tieback and liner, one of the major challenges is the wellbore temperature variation due to the high-rate fracturing. In such a case, the axial shrinkage trend of the casing string could be caused due to the sudden drop in temperature, but the actual axial length of the casing string would not change due to the cement constraints. Therefore, this could lead to cementation damage between the casing and cement due to excessive load from the casing string. A wellbore seal that is out of control often leads to irreversible consequences, even well abandonment. In order to study the mechanism of casing deformation in shale oil and gas wells with tieback and liner quantitatively, in this paper, take LS1 well (a typical shale oil and gas well with tieback and liner, and casing deformation is caused) for example, the transient changes of temperature and pressure in the whole wellbore during multistage fracturing are studied. Moreover, the cementing strength test of the interface between casing and cement is also tested. Then, the testing results are carried out and extended to model the finite element (FE) model with the whole vertical section casing string with tieback and liner. The model is used to simulate the internal force changes under fracturing conditions with different stages of fracturing. Meanwhile, the casing deformation mechanism in LS1 well is analyzed and studied in detail. Our simulation results indicated the failure process and mechanism of cementation between casing and cement in shale oil and gas wells with tieback and liner. Our work can provide a detailed theoretical reference and a basis for field application.